PM4 Maintenance Interval Schedule (MIS): Skid Steer Loader/Multi-Terrain Loader Family

Failure to lock out equipment before working on it accounts for:

1. 2% of the industrial accidents each year

2. 5% of the industrial accidents each year

3. 10% of the industrial accidents each year

4. None of the answers are correct

10% of the industrial accidents each year

You should warm the machine to:

1. Operating temperature

2. Cycle all controls

3. Move the machine to warm and circulate oil

4. None of the answers are correct

Move the machine to warm and circulate oil

The #1 priority of any job is:

1. Attire

2. Safety

3. Correct technique

4. None of the answers are correct

Safety

To ensure safety in respect to attire, you should:

1. Wear safety glasses

2. Wear safety shoes

3. Do not wear finger rings

4. All of the answers are correct

All of the answers are correct

When checking the engine coolant level, don't just check the overflow bottle, also check the level in:

1. The engine

2. You don't need to check elsewhere

3. The radiator

4. All of the answers are correct

The radiator

"Right" and "left" on the machine is determined by:

1. The operator's sitting position in the cab

2. Looking at the back of the machine

3. Looking at the front of the machine

4. None of the answers are correct

The operator’s sitting position in the cab

(True or False) The pressure in the hydraulic system must be released before lines and components can be removed:

True

If a funnel must be used to refill oil, be sure to use a:

1. Short-neck funnel

2. Long-neck funnel

3. Any length of funnel

4. None of the answers are correct

Short-neck funnel

Ensure that the arrow on the in-line filter points:

1. Upward

2. Downward

3. To the side

4. None of the answers are correct

Upward

When replacing the primary fuel filter, the drain valve is located:

1. On the top of the water separator bowl

2. On the bottom of the water separator bowl

3. On the side of the water separator bowl

4. None of the answers are correct

On the bottom of the water separator bowl

The primary filter can be cleaned up to:

1. 2 times

2. 6 times

3. 4 times

4. None of the answers are correct

6 times

The secondary air filter must be:

1. Cleaned

2. Replaced

3. You don't do anything with the secondary filter

4. All of the answers are correct

Replaced

Sprocket bearings:

1. Require no maintenance under normal conditions

2. Should be inspected, cleaned, and repacked if the machine is used in muddy or wet conditions

3. When lubricating, use a mallet to remove housing plug

4. All of the answers are correct

All of the answers are correct

When inspecting the sprocket assembly:

1. Check the outer sleeves to ensure they rotate feely

2. Check the sprocket rings for wear or damage

3. Check the torque on the nuts

4. All of the answers are correct

All of the answers are correct

Operators are responsible for basic visual inspections of the track tension:

1. Every 1000 hours

2. On a daily basis

3. Every 500 hours

4. None of the answers are correct

On a daily basis

Tracks that are too tight can cause:

1. Premature failure of tracks

2. Power loss

3. Bearing failure

4. All of the answers are correct

All of the answers are correct

There are _____ chain drives on the skid steer loader.

1. Four

2. Two

3. Five

4. None of the answers are correct

Four

(True or False) To adjust the chain drive tension you must remove the tire and rim.

True

There are a total of ___ retaining bolts for the ROPS.

1. Eight

2. Six

3. Four

4. None of these answers are correct

Four

There are a total of ___ retaining bolts for the FOPS.

1. Eight

2. Six

3. Four

4. None of these answers are correct

Eight