GPs

IPP operation limits with cover 4101 removed

-Max IPP oper. w/ cool down ____ minutes

-Req’d Interim cool down w/ IPP off ____ minutes

-Max oper. time after cool down ____ minutes

-Req’d cool down time to set time back to max w/ IPP of ____ minutes

35 / 20 / 35 / 20

FUEL CRITICAL ICAW is set at ____. Judgment of personnel and task being performed will dictate minimum quantity of fuel on aircraft before IPP operation.

1000 LBS

When _____ switch is set to on, ____ will automatically be performed.

28v BATT / SBIT

During SBIT, _____ and _____ lights will come on for approximately _____ and then go off.

28v low / 28v Discharge / 1 second

When ____ is complete, ____ light will come on and stay on

SBIT / 28v Discharge

If ____ light is flashing, IPP must be started within ____ to make sure IPP start is successful.

28v low / 30 seconds

If ____ light is flashing for more than ____, 28v battery will automatically go off. If automatic shutoff occurs, ____ switch must be set ____ and then 28v batter must be charged.

28v low / 60 seconds / 28v BATT / OFF

_____ should become available approximately ____ after 28v BATT switch has been set to ON.

Left MFD / 2 minutes

Operate UHF radio to local tower frequency ____

335.8

____ switch is not functional until after ____ is on (____ after 28v BATT switch was set to ON).

IPP / VMC / 15 seconds

____ switch must be held to ____ for ____ so ____ battery system can complete ____.

IPP / Start / 3 seconds / 270v / SBIT

____ and ____ lights will flash ____ time when IPP switch is set to ____ and shows lights are operating correctly.

270v low / 270v Discharge / 1 / Start

____ light should come on showing that 270v battery is discharging.

270v Discharge

If ____ light is on, IPP start can continue to be performed.

270v low

IPP switch will automatically move to ____ when released.

AUTO

If IPP has failure during start or operation, IPP should automatically ____.

Shutdown

Selecting ____ will not stop start sequence.

IPP OFF

IPP start sequence can only be stopped before ______ comes on solid by pushing ________ light button (emergency shutdown).

COMBUSTER light / IPP EMER OFF FIRE

IPP will not enter ____ cool down when IPP EMER OFF FIRE light button is pushed.

2 minute

If IPP EMER OFF FIRE light button is pushed, ____ light must go off. If light does not go off, IPP EMER OFF FIRE light button must be pushed again, and then ____ light must be inspected again.

270v Discharge / after 5 seconds

IPP combustor light will become solid when IPP is at command speed for standby mode (approximately ____ after START is selected).

30 seconds

IPP will have ______ during normal operations and can be heard.

Speed fluctuations

If ____ does not become available within ____, IPP must be shutdown immediately and troubleshooting performed.

Left MFD / 5 minutes

Ensure ____ indicator light is ____ when IPP combustor indicator light ______ and comes on solid.

270v Discharge / not on / Stops Flashing

Ensure ____ indicator light is not on ____ after IPP combustor indicator light comes on solid.

28v Discharge / 15 seconds

ENGINE INDICATIONS AND PARAMETERS PRIOR TO START

THRUST

HYD A

N1 RPM

OIL

FF (FUEL FLOW)

HYD B

NOZZLE

N2 PRM

EGT

COLOR VALUE

Red 000

Yellow N/A

Green less than 5%

Red less than 20 psi

Green 000

Yellow N/A

Green 100 to 106% open

Yellow less than 5%

Green uncalibrated between 20-60 degrees C

Maximum ESG Operation time

Engine can be motored maximum of ____.

2 minutes

Minimum IPP operation time

IPP must be operated minimum of ____ before motoring engine.

1 minute

ICC overheating

If ____ attempts are made in 120 minute period, ESG must have ____ cool down or ____ of IPP operation to decrease ____ and ____ Temperature.

2 Start / 120 minute / 10 minutes / ICC1 / ICC2

Component Overheating

If overheating component ICAW are asserted _____ sequence must be stopped and ____ must continue to operate to decrease component temperature.

motoring / IPP

Engine start is not recommended until after ____ of PCD is on (approx. ____ after IPP start)

Right side / 2 minutes

PARKING BRAKE must be cycled form ____ position to ____ positing and then to PARKING BRAKE position to engage.

Parking brake / OFF

Engine can be motored ____ time with GEN HOT 1&2 ICAW shown. If GEN HOT 1&2 ICAW ____ go away during ____ motor, motoring must be stopped to troubleshoot

1 time / does not / 2 minute

Engine must not be motored with ____ HOT ICAW showm

FUEL

Engine can be motored with GEN OIL FAIL 1&2 ICAW but must go away within ____ or engine motoring should be stopped. Engine motoring can be tried for a ___ attempt but also must go away within ____. If ICAW is still present after ____ motoring must be stopped to troubleshoot.

45 seconds / 2nd / 45 seconds / 45 seconds

When motoring, monitor engine indications of PCD engine page and make sure ____ RPM stabilizes at ____% RPM’s.

N2 / 11-19%

ICAW’s Before Engine Operation

_______ ICAW = Engine motoring must be performed

_______ ICAW = Engine must not be operated

GEN HOT 1&2

FUEL HOT

ICAW’s During Engine Operation

________ ICAW = If ICAW does not go away when engine gets to idle, engine operation must be stopped to troubleshoot

GEN OIL 1&2

If ETR higher then idle is required, engine must be operated for a minimum of ____ before advancing throttle.

2 minutes

IPP must be operated for minimum of ____ before engine start.

1 minute

Fuel Feed tank temperature must be more than ____ prior to engine start.

-18 Degrees C

Oil pressure can decrease into ____ range for approximately ____ during start sequence, and then rebound into the ____ range.

Red / 3 seconds / Green

Oil pressure should increase with increasing ____ RPM and when above ____ PSI, oil pressure gauge will turn green and ____ gauge will turn yellow.

N2 / 15 PSI / ETR

Engine start is not permitted if tailwinds is more than _____.

30 knots

If engine motoring was performed, engine N2 must be ____ before engine operation can be performed.

0%

Engine ____ RPM must always be ____ prior to switching engine states.

N2 / 0%

If ambient temperature is less than ____, 2 minute motoring must be accomplished.

0 degrees F

If engine start is less than ____ of abnormal engine shutdown or less than ____, but greater than ____ from normal shutdown, ____ engine motoring must be performed prior to engine start that follow.

6 hours / 6 hours / 20 minutes / 2 minute

Engine Start will ____ if ____ RPM does not get to ____% withing ____ or ____% withing ____.

AUTO Abort / N2 / 20-22% / 45 seconds / 55% / 150 seconds

After engine start ensure ____, ____ and ____ are off.

DAS / EOTS / RADAR

Engine must have been at idle (less than ____) for minimum of ____ before shutdown, to let engine cool down.

15% ETR / 5 minutes

If vehicle system IBIT is performed during engine operation, engine must be operated for ____ after IBIT is completed.

15 seconds

FPS fire bottle will automatically release approximately ____ after fire is detected in IPP or IPP exhaust bays.

10 seconds

FPS fire bottle will not release if BATT switch is set to ____

OFF