I-Car Collision Repair Fundamentals Post-Test Review

What action should be taken if a vehicle has a broken window during repair?

Cover the window opening to protect the interior

The wire wheel tool is used to perform all the following tasks EXCEPT:

Remove paint nibs

Which feature reduces the likelihood of whiplash in a crash?

Properly positioned headrest

Which of the following statements is true regarding respirators?

Half- and full-facepiece respirators can use both filters and cartridges

All of the following may require advanced driver assistance system (ADAS) calibration after collision repair work EXCEPT:

Replacing the hood

Why is it preferable to sand with a sanding block rather than without one?

It results in a straighter surface

What is the purpose of a seat belt pre-tensioner?

Helps secure vehicle occupants by removing slack in the seat belt

Which of the following is a true statement about a subframe?

It may be designed to absorb or transfer collision energy

In the vehicle-maker service information, where would a technician find the term a manufacturer uses for "rocker panel?"

Service terminology section

All of the following conditions typically require the use of an air-purifying respirator (APR) EXCEPT:

When seam sealing operations are being performed

Which marking confirms that face and eye protection meets ANSI standards?

ANSI standard number Z87 or Z87+

Which type of safety equipment can help save your eyesight following contact with hazardous substances?

Eyewash station

What benefit does clearcoat provide for a vehicle's finish?

Shields underlying layers from ultraviolet (UV) exposure

What kind of sanding block provides the straightest finish on a flat panel?

Extra-long and rigid

All of the following are true about gas metal arc (GMA) welds EXCEPT:

It has a smaller heat affect zone than resistance welding

Which advanced driver assistance system (ADAS) part is responsible for identifying vehicles and signs?

Front-mounted camera

What is an eraser wheel designed to remove?

Decals and adhesive residue

Which best describes the concept of collision energy management in vehicle design?

Absorbs and distributes crash forces through the vehicle structure

When explaining air hose usage, what is the primary hazard of leaving it on the floor?

A tripping hazard

Which issue may be covered under a paint manufacturer's warranty?

Peeling or delaminating finish

What process forms metal panels by pressing them into molds with high force?

Stamping

What is the first step to do in the event of an uncontainable or extremely dangerous spill?

Notify others in the area

How often should the emergency eyewash and shower station be activated to flush out any sediment buildup on the supply line?

Weekly

What's the best technique when operating an eraser wheel on decals?

Side-to-side motion using light force

Which statement about weld bonding using spot welds is correct?

Spot welds should be applied before the adhesive cures

All of the following are a type of steel EXCEPT:

Ultra-mid

What material is most effective to protect surrounding surfaces from overspray during refinishing?

Plastic sheeting

All of these are part of the three primary sections of a vehicle EXCEPT:

The upper section

What is a correct statement about filters and cartridges used in respirators?

Filters capture solid particles; cartridges absorb gases and vapors

In the event of a frontal collision, which part is engineered to collapse?

Steering column with dual shafts

When working on high-voltage electrical systems, which is a required personal protective equipment item?

Insulated gloves

What is the main purpose of a temperature monitoring tool?

Monitors how hot a part becomes during heat application

All of the following are abrasive tools EXCEPT:

Polishing pads

When discussing welding, flash burn is defined as:

A burn to the eyes cause from exposure to ultraviolet light from the welding arc

Which of these statements about heat guns is true?

Heat guns can be used to remove pinstripes, decals, and emblems

All of the following are true about bumper reinforcements EXCEPT:

They are welded to the upper front rails

What does a higher sandpaper grit number indicate

The abrasive is finer

Who is authorized to dispose of toxic automotive waste materials?

A waste hauler with proper licensing

To find out what personal protective equipment is needed before handling a substance, you should:

Check the safety data sheet (SDS)

What type of corrosion happens due to contact between steel and aluminum

Galvanic corrosion

How should open A/C lines be properly protected during service?

Use caps to cover the exposed openings

Where is the correct location for the negative cable when using a booster to jump-start a battery?

Metallic engine ground away from the battery

What should be done with a damaged abrasive disc?

Replace it with a new one

What hearing protection is necessary for extended exposure to 105 dB noise levels?

A combination of earmuffs and earplugs

A random orbital sander is used for all of these tasks EXCEPT:

Block sanding filler

The purpose of using noise, vibration, and harshness (NVH) materials includes all of these EXCEPT:

Enabling panel flutter

Where are noise, vibration, and harshness (NVH) materials commonly applied in a vehicle?

Rocker panels, pillars, and door panels

What is the first step when disconnecting supplemental restraint system (SRS) connectors?

Disengage the lock from the release

All of these practices help prevent slip, trip, and fall hazards EXCEPT:

Having proper workspace ventilation

What must be done before welding begins on a vehicle?

Shield the area with welding blankets and spark paper

What should not be done when handling 12-volt batteries?

Remove vent caps from maintenance-free batteries.

What should random orbital sanders not be used for?

Buffing topcoats.

Which of the following is not an abrasive tool?

Welding tools.

What task can the wire wheel tool not perform?

Flattening welds.

What is true regarding sandpaper grit and grading?

The higher the number, the finer the grit.

What is corrosion that occurs when two dissimilar metals are placed in contact called?

Galvanic corrosion.

What is a best practice for preventing slip, trip, and fall hazards?

Maintaining a clean workspace by picking up after yourself.

What do cut-off tools use to cut through metal?

Thin discs

Which jack or lift uses air to lift a vehicle?

Option B

Which block type should be used on a flat surface to achieve the straightest repair?

The longest

What is required for spot welds in weld bonding?

All spot welds must be completed while the adhesive is wet.

What does a paint manufacturer warranty cover?

Delamination.

What is true about gas metal arc welds?

Filler metal is not required.

Can air hoses contain compressed, high pressurized air that can cause serious injury?

True

Does a sanding block provide a stable backing for sandpaper?

True

Do broken window openings need to be covered to protect the vehicle interior?

True