Engineer practical ques.

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/246

encourage image

There's no tags or description

Looks like no tags are added yet.

247 Terms

1
New cards

What is the minimum blowdown for a spring loaded safety valve as a percent of the set pressure?

10% of the set pressure

2
New cards

How are Main Steam pressure gages tested?

With an Inspector's gage

3
New cards

Which code governs plumbing installations?

The NYC Plumbing Code

4
New cards

When are anchorages or guides inspected?

Annually

5
New cards

How many brass washout plugs does a miniature boiler have?

3 brass washout plugs, 1 inch in size

6
New cards

How often are HP piping expansion joints inspected?

Weekly

7
New cards

How long should a hydronic system be pressure tested?

2 hours at no less than 100 PSIG

8
New cards

How is a gage protected from excessive pressure?

A shut-off cock

9
New cards

Who is authorized to witness a test on a gas piping system?

A Plumbing Inspector, Architect, Licensed PE, Master Plumber, or an agency approved by the D.O.B

10
New cards

How should a remote disconnect be labeled?

Remote control for burner

11
New cards

When is a fusible plug not required on a boiler?

Boilers over 200 PSIG

12
New cards

When must a power boiler with a MAWP over 400 PSI be tested?

Pressure tested annually

13
New cards

What does a design plan for a boiler and application contain?

Size, location, operating pressure and temperature of the pressure vessel, and the type and specification of the PRV

14
New cards

Who maintains copies of certified welder qualification reports?

The welding agency, which must make them available to the D.O.B

15
New cards

Who must furnish a control diagram and boiler operation instructions?

The installer

16
New cards

Who certifies and calibrates all gages used for testing?

A testing operator

17
New cards

What is placed between different types of joints and piping materials?

An approved adapter fitting

18
New cards

What items are exempt from reporting requirements?

Seal welds of tubes and installation of back rings to manholes and handholes of boilers

19
New cards

Who controls welding performed on a high pressure tank?

An engineer supervising a welding inspection agency acceptable to the D.O.B

20
New cards

At what pressure are extra heavy valves required?

100 PSIG

21
New cards

Who files an application for a boiler alteration?

Inspector

22
New cards

How many safety valves does a boiler with over 500 square feet of heating surface have?

2

23
New cards

What must gas-fired boilers not exceeding 100 square feet of heating surface have?

A single or double cone type hood diverter in the stack

24
New cards

Where shall a heater for liquid fuels or other boiler-harmful liquids not be installed?

Directly in the steam or water space within a boiler

25
New cards

Who is responsible for spatial relationships between tanks and gas services?

The installer of the last installation, who must correct the violation

26
New cards

Who is responsible for setting operating and safety controls?

The installing company

27
New cards

What safety fitting protects high pressure steam and water boilers?

Dual low water cutouts

28
New cards

What total combined relieving capacity must spring loaded safety valves have?

100% of the maximum designed capacity of the boiler

29
New cards

What is the total combined relieving capacity of power actuated relieving valves?

No less than 10% of the MAWP and no more than 20% above the MAWP

30
New cards

What is the minimum blowdown for a spring loaded safety valve?

2%

31
New cards

When a boiler is derated, what changes?

The MAWP decreases and the BTU output decreases

32
New cards

Where shall shutoff valves be installed in hydronic piping systems?

Before and after the pressure reducing valve

33
New cards

How must hydronic piping joints between steel tubing and fittings be made?

Mechanical or welded

34
New cards

What appears on a boiler's nameplate?

Serial number, name of manufacturer, manufacturer's serial number, MAWP, heating surface, year built, and rated steam capacity

35
New cards

Where must boiler waste gas be conducted?

To the atmosphere

36
New cards

What is installed on a line when a quick-closing valve creates water hammer?

A water hammer adapter

37
New cards

What are the three ways safety valve capacity may be checked?

Accumulation test, amount of fuel burned, and evaporative capacity of feedwater

38
New cards

Where are inspection records kept?

On the premises

39
New cards

Repacking of which joint types does not require a work permit for anchorages or guides?

Ball or slip joints

40
New cards

What must be done before an internal high pressure inspection?

Shutdown, drained, and removal of hand and manholes

41
New cards

What is the blowoff tank outlet size requirement?

Outlet is 2 times the diameter of the blowdown piping, with a 6 inch internal pipe entering the bottom of the blowoff tank

42
New cards

What info is not necessary to send to D.O.B?

Use, type, size, location, and operating temperature of pressure tanks, and location, type, and specs of the pressure relief valve

43
New cards

What are the specs of a miniature boiler?

16 inch inner diameter, 5 ft gross volume, 20 sq ft heating surface, less than 100 PSIG MAWP

44
New cards

What are the safety valve popping point tolerances by pressure range?

Up to 70 psig: plus or minus 2 psig; 71-300 psig: plus or minus 3%; 301-1000 psig: plus or minus 10 psig; over 1000 psig: plus or minus 1%

45
New cards

What are other ways to test a safety or relief valve for rated capacity?

Accumulation test, amount of fuel burned, and evaporative capacity of feedwater

46
New cards

What happens if someone fails to follow gas piping inspection rules and regulations?

Revocation of license

47
New cards

For a 5 psig gage, what range must not be exceeded?

10 psig (2x the operating pressure)

48
New cards

What can be connected to the float chamber or water column?

A damper regulator, feedwater regulator, gage, and drain

49
New cards

On a steam gage, what keeps the tube filled with water?

A siphon

50
New cards

What is the minimum working clearance around boilers and vertical clearance?

NYC code requires 18 inches, High Pressure code requires 24 inches; vertical clearance is 7 feet

51
New cards

Who sets, adjusts, and tests boiler controls?

By the installer

52
New cards

What do mufflers prevent?

Back pressure

53
New cards

What valve is on the external piping of a desuperheater?

Stop valve (external)

54
New cards

How often must a boiler with MAWP up to 400 psi be tested?

Once a year

55
New cards

What is the minimum safety or relief valve capacity for electric boilers?

3.5 lb/hr/kW

56
New cards

Who retains a copy of the report after welded repairs or alterations?

The owner

57
New cards

Who receives the application for permission to install a second boiler?

Commissioner

58
New cards

How much clearance is needed to go on top of boilers for maintenance?

7 feet

59
New cards

How far above the floor must wet-bottom boilers be set?

12 inches

60
New cards

Where do you find the information needed to set safety and relief valve pressure?

The nameplate of the safety valve

61
New cards

If one safety valve is on an electric boiler, what is the maximum output?

Less than 1100 kW

62
New cards

What pressure must a system using utility street steam have?

200 PSIG at 413°F, then reduced by a PRV

63
New cards

What chemical should be used for oxygen scavenging?

Sodium sulfite or sodium hydroxide

64
New cards

What is the minimum distance from the wall to the boiler?

18 inches in NYC Construction Code, 24 inches in High Pressure Code

65
New cards

What is the lowest part of a water gage?

2 inches above the lowest permissible water level

66
New cards

What standards are used for gages?

ASME and ANSI

67
New cards

What is the only thing that can tap onto a low water cutoff?

A drain

68
New cards

How many expansion tanks are needed for 6 boilers?

1

69
New cards

Who designs the boiler system?

The professional engineer or the architect

70
New cards

For a 5 psig gage, what is the minimum calibration increment?

1/5 inch increments

71
New cards

At what percent of MAWP is a boiler hydrostatically tested?

150%

72
New cards

Besides the state boiler inspector, who else can look at the log book?

The insurance company

73
New cards

What is the difference between low and high pressure safety relief valves?

Low pressure relieves to a drain, while high pressure relieves to a vent

74
New cards

What is the minimum dial arc on a 2 1/4 inch gage?

270 degrees

75
New cards

Where is the steam gage installed on a miniature boiler?

On the steam space side

76
New cards

What is an effective stop for a gauge?

The indicating point at zero

77
New cards

How long is the prepurge on a low pressure boiler?

90 seconds

78
New cards

What do the stamps S and H mean?

S means power boiler; H means low pressure boiler

79
New cards

How many drains must each superheater have?

At least one

80
New cards

How often does an insurance inspector inspect boilers?

Annually

81
New cards

What boiler work is exempt from reporting?

Replacement of backings to manholes and handholes, and seal welds to tubes

82
New cards

How do you prepare a brazed joint and a weld?

Braze: clean, flux, heat, filler metal. Weld: clean, bevel/convex, weld with filler metal, wire wheel

83
New cards

On what boilers are mufflers not to be installed?

High pressure boilers

84
New cards

What happens if discharge and supply strainers are clogged?

Deep vacuum

85
New cards

How many safety valves are on a miniature boiler?

1 safety valve, since it has only 20 sq ft

86
New cards

What is used between two different types of metallic pipe?

A dielectric kit or fitting

87
New cards

Where is gas service or distribution line from a new high pressure tank installed?

In a separate room

88
New cards

How many square feet of heating surface does a fusible plug require?

50 sq ft

89
New cards

Where does a low pressure safety relief valve discharge?

The drain

90
New cards

At what power output do electric boilers need two or more safety valves?

1100 kW

91
New cards

How many safety valves are required for an electric boiler operating at a maximum of 1100 kW?

2

92
New cards

When is a bullseye water sight glass acceptable on a miniature boiler?

When there is insufficient space for a gage glass on a miniature boiler

93
New cards

Where is the inspector notice posted after being given to the owner?

On or close to the boiler

94
New cards

What type of welding must pipes 2 inches or larger have?

Butt welding

95
New cards

For a 3 psig gage, what is the calibration increment?

1/10

96
New cards

What are the minimum and maximum temperatures for a hydrostatic test?

Above ambient temperature; code range 70-120°F

97
New cards

Where does a low pressure safety relief valve discharge?

A drain

98
New cards

How do you prepare a soldered joint?

Clean, flux, heat, solder

99
New cards

How often do you bottom blow off a boiler?

Daily

100
New cards

Who authorizes changes to high pressure piping anchors, guides, and expansion joints without affecting health and safety?

The professional engineer