Google Drive Review

What is Electric Shock?

The sensation and muscular spasm caused by electric current passing through the body.

What causes electric shock?

Current, and not voltage, causes electric shock.

What is HERO?

Hazards of Electromagnetic Radiation Ordnance.

Which app provides an environment for sharing data?

CAS - Collaboration at Sea.

What frequency is used for Long Range Communications?

HF (High Frequency).

What type of wave is HF?

Sky Wave.

What does Emissions Designator represent?

A frequency via 7 characters.

What document provides procedures or reference information?

CIB - Communications Information Bulletin.

What can be found in a Frequencies Plan?

Frequencies.

Which CIB is for SHF?

CIB 7E.

What component connects Crypto to the Channelizer?

RED SAS.

What does a Multi-Coupler connect to?

Multiple Transceivers to one Antenna.

How to make a Yankee Circuit secure?

Put the Crypto in Cipher Mode.

Where do we find programming procedures?

Tech/Instruction Manual.

How to verify a circuit is operational?

Comms Check.

Which Amplifier is used for HF on the DMR?

AM-7625/USC-61(C) 500 Watt.

What do we use the Oscilloscope for?

Service, Repair, and Test various Comms.

What is the purpose of a Spectrum Analyzer?

Analyze RF Signals.

What system do we use for Message Traffic Onboard?

NAVMACS.

What component supplies power to the NAVMACS?

VME Chassis.

What allows you to edit messages?

OPINT - Operator Intervention.

Can we delete messages on the NAVMACS?

No.

What moves at 75 Baud Rate?

Fleet Broadcast/November Circuit.

How do we know if Fleet Broadcast is active?

Green Light on the Control Panel.

Is CO approval required for message sending?

No.

What do we use COMMSPOTS for?

Disruption or troubleshooting of Comms.

What publication governs BSRs?

NTP4.

What allows you to view messages?

Message Log.

How to avoid Electric Shock?

Electrically Rated Rubber Gloves and Battery Powered Power Tools.

What is the best practice for HERO?

De-Energize equipment or place on Standby.

What LOS Circuit can we use within a Strike Group?

Fleet Tactical.

What comes after Net Prioritization in OPTASK development?

Guarding Requirements.

What is the minimum classification of the COMMSPLAN?

Confidential.

What do we use the Frequencies Plan for?

To assign Frequencies.

What message grants Satellite Connectivity?

SAA - Satellite Access Authorization.

What is the minimum separation of frequencies on a Multi-Coupler?

3 MHz.

What sits on top of the SRAs?

CA-11.

What antenna do we use to receive on a Yankee Circuit?

OE-416 Dual Whip.

What resources do we use to set up any circuit?

SOP, COMMPLAN, and Tech Manual.

Where do we plug the Headphones into on the 2368?

Phones Jack.

What resource would we use for the Line, Channel and Trunk information?

Comm Status Board.

What is the first step of troubleshooting?

Identify the Problem.

What amplifier would we use on the DMR for UHF and VHF?

AM-7584/USC-61(C) 200 Watt.

What resource provides setup?

SOP.

What does an Oscilloscope analyze?

Signals, Voltage, and Integrity of Electrical Circuits.

What log will we go into to manually Create and Route Messages?

OPINT.

What are the most used Modes on the NAVMACS?

Message, OPINT, and Section.

What circuit do we use to Route Messages while in Homeport?

Fleet SIPRNET Message.

What are the two Circuits on the NAVMACS to Transmit and Receive?

MMS - Multi-Messaging System and CUDIXS - Common User Digital Information Exchange System.

Why would we send out a BSR?

To Re-Transmit.