1/44
Looks like no tags are added yet.
What is Ionicity in relation to contrast agents?
Ionic contrast agents dissociate into charged particles in water and blood, and are known to be more toxic due to increased osmolarity.
What is osmolarity?
A measure of the osmotic pressure of a solution regarding the number of particles per volume of solution, with blood having approximately 300 mOsm/L.
Are most IV contrast agents ionic or nonionic?
Most common IV contrast agents are non-ionic, meaning they do not form charged particles in the blood.
Why is water-soluble iodine the only acceptable contrast agent for IV injection?
It is chemically bound to a benzene ring, making it biologically compatible with the body.
How is barium used in CT different from barium used for fluoroscopy exams?
CT Barium is a suspension of barium sulfate (high atomic number) administered orally or rectally, whereas fluoroscopy barium is different.
What are the dietary restrictions for administering IV contrast?
Pre-hydration; NPO 1 hour; post-hydration.
What is the normal range for BUN levels?
7–21 mg/dL.
What is the normal range for Creatinine levels?
0.7–1.5 mg/dL.
What is the normal range for GFR?
90–120 mL/min.
What BUN level may indicate renal failure?
Above 50 may indicate renal failure.
What Creatinine level may indicate renal failure?
Above 2.0 may indicate renal failure.
What GFR level may indicate renal failure?
Below 30 may indicate renal failure.
What medications are commonly used to premedicate a patient with an iodine allergy?
Corticosteroids (prednisone) and antihistamines (diphenhydramine, Benadryl).
What is cannulation?
The process of placing a peripheral IV.
What are the preferred sites for placing an IV in CT?
Cephalic vein, Basilic vein, Median cubital vein.
Why should small veins of the hands and wrist be avoided for IV contrast injection?
Risk of blowing out since 20 or larger gauge needed
When should hand hygiene be performed during IV cannulations?
First step of aseptic technique: wash hands, then wear gloves, and clean the skin.
What kind of gloves are required when starting an IV?
Just clean, not sterile
Under what circumstances can a technologist use the patient’s venous catheter for pressure injections?
20 gauge or higher catheters in the antecubital or forearm; labeled PICC lines and central lines with max injection rate provided.
What type of venous access devices are not acceptable for pressure injections?
Jugular lines and dialysis catheters.
What is extravasation?
The leakage of contrast (or any fluid) outside the blood vessel.
What are the initial signs and symptoms of extravasation?
Not provided in PowerPoint.
How is extravasation treated?
Elevate extremity, Heat to dissipate contrast, cold to help with pain
What is the treatment for an air embolism?
Administration of 100% oxygen and placing the patient in left lateral decubitus.
What are the mild contrast reactions?
Urticaria, Pruritus, Rhinorrhea, Nausea, Vomiting, Coughing, Dizziness.
What are the moderate contrast reactions?
Persistent Vomiting, Diffuse Urticaria, Headache, Facial Edema, Moderate laryngeal edema, Moderate Bronchospasm, Hypertension, Abdominal Cramps.
What are the severe contrast reactions?
Life Threatening Arrhythmias, Altered Mental Status, Severe Hypotension, Severe Bronchospasm, Laryngeal edema, Pulmonary edema, Seizures, syncope, and death.
What is the technologist's first responsibility during an adverse contrast reaction?
Immediately discontinue contrast administration.
What medication is typically administered for hives and itching?
Antihistamine (Benadryl).
What are the contraindications for iodinated contrast?
Iodine allergy, Renal Failure, Recent contrast administration.
Is there evidence that iodinated contrast poses a risk to a developing fetus?
No evidence suggests risk, but use is discouraged unless necessary.
How is the Computed Tomography Dose Index (CTDI) calculated?
By scanning CTDI phantoms embedded with ionization chambers to measure absorbed dose.
What units is CTDI measured in?
Milligray (mGy).
What is Dose Length Product (DLP)?
The product of the dose multiplied by the scan length, representing total dose and tissue exposure.
If the CTDI for a scan is 21 mGy and the scan length is 42 cm, what is the DLP?
882 mGy-cm.
Which is better for evaluating total radiation received by a patient, CTDI or DLP?
DLP is better for evaluating total radiation received and estimating biological effects.
What is the concept of optimal dose in CT?
Dose that produces quality images with the lowest possible radiation dose.
How does increasing mA affect patient dose?
Patient dose increases (directly proportional).
How does increasing kVp affect patient dose?
Patient dose increases.
How does increasing pitch affect patient dose?
Patient dose decreases (inversely proportional).
How does increasing beam width affect patient dose?
Patient dose decreases.
Why is it important to position the patient directly in the center of the gantry?
Scans using automatic modulation adjust dose based on scout images.
How does automatic dose modulation work in CT?
The CT scanner adjusts the mA during the scan based on tissue density.
What is the difference between a dose notification and a dose alert in CT?
Dose notification allows review of settings before exceeding threshold; dose alert warns when cumulative CTDI exceeds 1,000 mGy.
What are the main differences between lead shielding and bismuth shielding?
Lead shielding causes artifacts and is not supported; bismuth shields reduce low-energy photon dose and can maintain image quality.