Chapter 5: The X-Ray Tube

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/26

flashcard set

Earn XP

Description and Tags

Flashcards covering Chapter 5: The X-Ray Tube, including tube housing, internal components, anode and cathode designs, line-focus principle, anode heel effect, circuit pathways, and safe tube operation.

27 Terms

1
New cards

What is the construction and primary purpose of the protective x-ray tube housing?

It is a lead-lined metal structure that provides mechanical support, serves as an electrical insulator, and provides a thermal cushion. It is immersed in an oil bath and uses cooling fans to dissipate heat.

2
New cards

What is the regulatory limit for leakage radiation escaping the protective housing?

It must be reduced to less than 100 mR/hr100\,\text{mR/hr} (0.0258 millicoulomb/kg/h0.0258\,\text{millicoulomb/kg/h}) at a distance of 1 meter1\,\text{meter}.

3
New cards

What safety precaution must be taken regarding the high-voltage cables attached to the tube housing?

Never use the high-voltage electrical cables as handles to move or maneuver the tube, as this can damage equipment and pose a risk to the radiographer.

4
New cards

Why must the x-ray tube envelope maintain a vacuum?

Without a vacuum, air electrons could join the electron stream, causing arcing and damaging the tube.

5
New cards

What are the characteristics and dimensions of the tube's target window?

It is a thinner section of the enclosure (usually about 5 cm5\,\text{cm} square) positioned at the x-ray exit point, designed to minimally absorb the useful x-ray beam.

6
New cards

What occurs during filament heating to produce electrons?

Current heats the filament to incandescence (white hot), causing electrons to boil off via thermionic emission and form an electron cloud called space charge.

7
New cards

What is the space-charge effect?

A self-limiting condition where, once the electron cloud reaches a size related to the current used, it becomes difficult for additional electrons to be emitted.

8
New cards

At what speed and over what distance do electrons travel from the cathode to the anode target?

Electrons reach speeds of about half the speed of light while traveling a distance of 1–3 cm1\text{–}3\,\text{cm} between the focusing cup and the target.

9
New cards

What is the major limitation of a stationary anode?

Electrons continually strike the same small area (a tungsten button embedded in copper), causing rapid heat build-up that damages the target and limits exposure techniques.

10
New cards

What materials are used in the construction of a rotating anode disc and shaft?

The disc consists of a molybdenum base/core coated with tungsten (often with rhenium added), mounted on a copper shaft containing a molybdenum core.

11
New cards

Why is tungsten chosen as the primary target material for the anode?

Tungsten has a high melting point (about 3400∘C3400^\circ\text{C}), high thermal conductivity, and a high atomic number (7474), which increases x-ray production efficiency.

12
New cards

How does the induction motor cause the anode to rotate?

Stator electromagnets outside the enclosure are energized in opposing pairs, inducing an electric current and magnetic field in the internal rotor through electromagnetic mutual induction.

13
New cards

What are the typical anode rotation speeds for general-purpose and specialty x-ray tubes?

Approximately 3,400 rpm3,400\,\text{rpm} for general-purpose tubes and up to 10,000 rpm10,000\,\text{rpm} for specialty tubes.

14
New cards

What is the line-focus principle?

A design using an angled anode target face to maintain a large actual focal spot for heat dissipation while producing a small effective focal spot for image sharpness.

15
New cards

What is the difference between the actual focal spot and the effective focal spot?

The actual focal spot is the area on the anode target bombarded by electrons, whereas the effective focal spot is the x-ray beam area as seen from the patient's perspective.

16
New cards

What are common target angles for general-purpose tubes, and what happens if the angle is too small?

Target angles range from 7∘7^\circ to 18∘18^\circ (most commonly 12∘12^\circ). If the angle is too small, the x-ray beam may fail to cover the full image receptor at the required source-to-image distance.

17
New cards

What is the anode heel effect and what relative beam intensities does it create?

It is the reduction in x-ray beam intensity on the anode side caused by photons being absorbed in the target heel, producing approximately 75%75\% intensity on the anode side and 120%120\% on the cathode side.

18
New cards

What are the dimensions and composition of the filaments in a dual-focus tube?

Each filament wire coil is 7–15 mm7\text{–}15\,\text{mm} long and 1–2 mm1\text{–}2\,\text{mm} wide, made of tungsten with 1%–2%1\%\text{–}2\% thorium added to enhance thermionic emission and tube life.

19
New cards

What material is the focusing cup made of, and how does it condense the electron stream?

It is made of nickel and receives a strong negative charge from the secondary circuit; electrostatic repulsion forces the electrons into a tight cloud directed toward the target.

20
New cards

What occurs during the first phase (rotor preparation) of the exposure switch?

Electricity is sent to the induction motor to bring the anode up to operating speed, while current energizes the selected filament to achieve desired thermionic emission.

21
New cards

What is the pathway of the high-voltage (kVp) circuit to the x-ray tube?

Voltage travels from the autotransformer to the step-up transformer (passing through capacitor banks and inverter in high-frequency units), through a rectifier bank, and then to the tube.

22
New cards

What are the three essential requirements for x-ray production?

(1) A large potential difference to give electrons kinetic energy (kVp\text{kVp}), (2) a source/quantity of electrons (mA\text{mA}), and (3) a target for interaction (the anode).

23
New cards

What are the three major causes of x-ray tube failure?

(1) Frequent use of very high or maximum exposure factors, (2) low but very long exposure factors that maintain high temperatures, and (3) filament overload from prolonged excessive heating or arcing.

24
New cards

What three heat transfer processes operate within the x-ray tube assembly?

Conduction transfers heat through materials; radiation transfers heat from the anode to the oil bath; convection transfers heat into the room via cooling fans.

25
New cards

What is the formula for calculating Heat Units (HU) and what are the correction factors for different generators?

HU=kVp×mA×s×c\text{HU} = \text{kVp} \times \text{mA} \times s \times c, where c=1.0c = 1.0 (single-phase), c=1.35c = 1.35 (three-phase, 6-pulse), c=1.41c = 1.41 (three-phase, 12-pulse), and c=1.45c = 1.45 (high-frequency).

26
New cards

Why should excessive rotor prepping be avoided?

Prepping keeps the filament energized at high temperatures, which shortens its useful operational life.

27
New cards

What physical damage occurs to the anode from repeated very high exposures?

Repeated very high exposures cause anode pitting, which consists of small localized areas of melting on the target surface.