1/44
Vocabulary practice flashcards covering power distribution systems, diversity factors, microgeneration rules, solar PV equipment, and transformer construction, operation, testing, and cooling.
Diversity
The ratio of the maximum demand to the connected load in an electrical installation.
Industrial Diversity Factors (ETCI Rules)
Design diversity allowances defined for specific industrial loads: 0.25 for mechanical engineering industry, 0.90 for food industry (including process engineering), 0.70 for cranes, and 0.50 for lifts.
Anti-Tamper Device
A closed-circuit security component designed to initiate an alarm condition when the access door, lid, or enclosure of intruder alarm equipment is opened by its normal method of opening.
Instrument Transformer Advantages
Three principal operational benefits: enables the use of standardised measuring instruments; provides increased personnel safety by allowing the secondary side to be connected to earth; and permits measuring instruments to be changed without isolating the main electrical supply by using a suitable short-circuiting switch and voltage links.
Grid-Connected Solar PV Electrical Components
The essential interface components required to link a solar PV array to the grid: a DC Isolator Switch (isolates panel output), an Inverter (converts DC to AC and synchronises with grid supply), an AC Isolator Switch (provides electrical isolation of the two AC supplies), and a kWh meter (measures electrical energy exported to the grid).
Stand-Alone Solar PV System Components
The key equipment needed for an off-grid solar installation supplying low-power consumption AC loads: Solar PV Panels, Charge controller, DC Disconnector, Batteries, and an Inverter (with or without SPD).
Microgenerator Interface Protections
Five electrical protection functions required when interconnecting a microgenerator to the national grid: undervoltage protection, overvoltage protection, underfrequency protection, overfrequency protection, and a means to detect loss of mains supply.

Dual Supply Warning Label Locations
Four mandatory positions where dual-supply warning signs must be posted in premises with microgeneration: at the ESB Networks metering position, at the consumer unit position, on all switchboards between the consumer unit and microgenerator, and at all points of isolation for the microgenerator.
Standard Test Conditions (STC)
The standardised laboratory reference conditions used to rate and compare solar PV modules: an irradiance of 1,000W/m2, a cell temperature of 25∘C, and an AM1.5 reference solar spectrum.
Air Mass (AM)
The relative optical path length that sunlight travels through Earth's atmosphere compared with the shortest near-vertical path; AM1.5 represents a path length approximately 1.5 times this reference length and relates to the solar spectrum.
ESB NC6 Form
A formal notification document submitted to ESB Networks advising that a customer intends to install a microgenerator; it provides owner/MPRN details, installer data, equipment specifications (including EN50438 compliance certificate), inverter maximum capacity in kVA, and generator type.
Mutual Inductance
The magnetic phenomenon where an alternating current changing in one coil induces an EMF in an adjacent coil; mutual inductance is one henry (1H) when a current change of 1A/s in the primary induces an EMF of 1V in the secondary.
Self-Inductance
The production of an opposing counter-EMF in a coil resulting from changes in its own current; its value is one henry (1H) when current changing at the rate of 1A/s induces an EMF of 1V within the same winding.
Inductive Time Constant (\tau)
The ratio controlling transient current growth and decay in an inductive RL network, calculated as τ=RL (henrys divided by ohms); transient rise or decay is considered complete after approximately five time constants (5τ).
Core-Type vs Shell-Type Transformer
Two distinct magnetic core constructions: core-type transformers split windings across both outer limbs to minimise leakage flux, whereas shell-type transformers concentrate both windings on a central limb flanked by two outer limbs that provide parallel magnetic return paths.
Concentric vs Sandwich Windings
Two winding configurations: concentric (cylindrical) windings feature one winding placed completely over the other (predominantly in core-type transformers), while sandwich (disc-type) windings divide primary and secondary coils into interleaved alternating discs (predominantly in shell-type transformers).
On-Load Tap Changer (OLTC)
An automated transformer switching mechanism that modifies the winding tap positions and turns ratio under full operational load without interrupting power, ensuring stable terminal voltage across variable supply or load demands.
Iron Losses (Core Losses)
The combined heat losses within a transformer's magnetic circuit composed of eddy current losses (minimised by thin laminations) and hysteresis losses (minimised by silicon steel); iron losses depend on frequency and peak flux density and remain practically constant from no load to full load.
Copper Losses
The heating losses generated in transformer windings due to conductor resistance (P=I2R); copper losses are proportional to the square of the operating load current and are assumed to be zero when the secondary is open-circuited (no-load condition).
Transformer Voltage Regulation
The percentage variation in secondary terminal voltage between zero load and full rated load caused by internal winding impedance, expressed as Vno loadVno load−Vfull load×100%.
Open Circuit Test (No Load Test)
A diagnostic procedure where rated voltage is supplied to the primary with the secondary terminals open; because the no-load magnetising current is very small (3–5% of full load), winding copper loss is negligible and the wattmeter reading indicates transformer iron losses.
Short Circuit Test
A transformer test where the LV winding is shorted by a thick conductor and a reduced voltage (5–10% of rated) is applied to the HV side to circulate rated full-load current; because core flux density is minimal, core loss is negligible and the wattmeter reading indicates full-load copper losses (I2R).
Conservator Tank
An elevated cylindrical tank mounted above the main oil-filled transformer body to accommodate the volumetric expansion and contraction of insulating oil during heating and cooling cycles, preventing excessive hydraulic pressure from rupturing the transformer tank.
Buchholz Relay
A protective gas-actuated safety relay fitted in the pipe linking the main transformer tank and conservator; minor faults liberate gas that displaces oil to lower an upper float and trigger an alarm, while severe faults cause violent oil surges that deflect a lower flap to trip the circuit breaker and isolate the transformer.
Silica Gel Breather
A moisture-extraction device connected to the conservator breathing pipe containing silica gel crystals that dehydrate air entering the transformer; dry crystals exhibit a blue tint, which turns pink as moisture saturates the gel, signalling the need for replacement or reactivation.
Transformer Bushings
Insulated feed-through assemblies that facilitate the connection of internal windings to external conductors through the grounded metal tank; LV bushings utilize porcelain or ebonite posts, while HV bushings operating above 33kV employ capacitor-graded bakelized paper and tin-foil layers encased in porcelain.
Arcing Horns
Paired spark-gap electrodes positioned across high-voltage insulator bushings (one connected to the line conductor and the other to tank ground) to safely divert overvoltage surges and lightning flashovers away from the fragile bushing porcelain and windings to earth.
ONAN and ONAF Transformer Cooling
Standard transformer cooling classifications: ONAN (Oil Natural Air Natural) cools through natural internal oil convection and natural external air currents over radiator banks; ONAF (Oil Natural Air Forced) maintains natural oil circulation but uses cooling fans to force air across the radiator exterior.
Conditions for Paralleling Transformers
The mandatory parameters required before paralleling two or more transformers: identical primary and secondary voltage/turns ratios, equal percentage impedance, identical tap changer positions, matching phase angle shift, identical rated frequency, correct relative polarity, and matching phase sequence.
Transformer Oil Crackle Test
A field test used to confirm that insulating oil is free from moisture, performed by gently heating a small oil sample in a test tube over a flame, where any audible crackling signifies the presence of water.
Transformer Oil Electric Strength Test
A dielectric breakdown test that evaluates the physical cleanliness and dielectric integrity of insulating oil by applying an increasing alternating voltage across submerged electrodes (typically 27–30kV) until a spark appears, averaging six consecutive readings.
Domestic Shower Circuit Sizing and Current (10kW at 230V)
Under ETCI rules:
Current without diversity: I=VP=230V10,000W=43.48A
Current with diversity applied: 40A
Fixed wiring cable: 6mm2 copper
Protective device: 40A MCB or fuse
Isolating switch: 40A
Current Transformer (CT) Multiplier and Secondary Reading (1,200A Load, 1,500/5 Ratio)
CT Multiplier: 51,500=300
Secondary ammeter reading: 3001,200A=4A
Industrial Distribution Board Load Calculation (40kVA at 0.8 PF Lagging and 35kW at Unity PF)
Active power (P): (40kVA×0.8)+35kW=32kW+35kW=67kW
Reactive power (Q): 40kVA×0.6=24kVAr
Apparent power (S): 672+242=71.17kVA
Solar PV Sizing Calculation for a 12kW Installation (400W, 1m×1m Modules)
Module power density: 400W/m2
Total surface area needed: 400W/m212,000W=30m2
Number of solar PV modules: 1m230m2=30modules
Measures to Manage Surplus Solar PV Generation During Low Domestic Demand
Three practical solutions to utilize daytime excess power:
Single-Phase Microgeneration Maximum Export Capacity (MEC) under ESB NC6
5.75kVA (nominally 6kVA), based on an inverter rated current output limit of 25A at a standard voltage of 230V (25A×230V=5,750VA).
Commissioning Verification Tests for Grid-Connected Microgenerators (EN 50438 / EN 50549)
Key verification tests required at commissioning:
Transformer Full-Load Copper Loss Calculation from Half-Load Loss (120kW at Half Load)
480kW; copper losses vary in proportion to current squared (P∝I2), so doubling current from half load to full load increases copper dissipation by 22=4 times (120kW×4=480kW).
Transformer Percentage Voltage Regulation Calculation (400V No-Load to 390V Full-Load)
2.5%, calculated using:
Vno loadVno load−Vfull load×100%=400V400V−390V×100%=2.5%
Transformer No-Load Voltage Calculation (220.8V Full Load, 4% Regulation)
230V, calculated using:
Vno load=1−100%regulationVfull load=1−0.04220.8V=0.96220.8V=230V
Fault Diagnosis for Parallel Transformer Voltmeters (V1=235V, V2=470V, V3=235V)
It is unsafe to close switch S. A reading of 470V across switch S indicates that the two secondary windings are connected in additive series opposition (opposite polarity). Closing switch S would cause a dangerous short circuit across a 470V potential.
Dual Safety Float and Flap Operation in a Buchholz Relay
Winding Insulation Resistance (IR) Test Connections for Power Transformers
With all line and neutral bushings fully isolated from the external supply:
Tertiary Winding Function in Star-Star (Y-Y) Transformers
An auxiliary delta-connected winding included in star-star systems to provide a path for circulating third-harmonic currents, stabilize the neutral point, and prevent severe voltage unbalance during single-phase loading.