MECH2100 Final Exam Theory - Structural Integrity Framework

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/19

encourage image

There's no tags or description

Looks like no tags are added yet.

20 Terms

1
New cards

Define Structural Integrity

Structural integrity is the engineering discipline of making sure a component or system performs its function without unacceptable failure

2
New cards

What are the four considerations for structural integrity?

Design inputs, structural modelling, factor of safety, and design calculations.

3
New cards

Define design inputs

Design inputs are the known/givens that define what the design must survive. This is where we deliberately look for credible condition or load that could lead to failure before moving to the structural model.

4
New cards

Design Inputs: What is the difference between Operating Conditions and Service Conditions?

Operating conditions are the things the design must do and the conditions it is under. Service loads are the things that act on the design during service like forces, moments, pressure, or static loading.

5
New cards

What are the three failure types and their definitions?

Technical failure - insufficient information about materials, structure, loading or operating conditions. Operational failure - the system is used, maintained or operated outside the intended conditions. Unpredictable failure - a rare circumstance.

6
New cards

Define structural modelling

To identify critically loaded points with minimal information. You complete this by tracing external actions through a component or assembly and the internal stresses it causes.

7
New cards

Structural Modelling: What do you trace?

Where the load enters, how it transfers across each connection, and where it exits at the support or reaction point.

8
New cards

Structural Modelling: What is the difference between direct vs transverse shear?

Direct shear is when an applied force cuts through a member. Transverse shear is when transverse loads generate bending moments and shear forces.

9
New cards

What is the structural distillation concept?

Reducing the real structure to the simplest model that still preserves the mechanics that matter. It is used to design against failure.

10
New cards

What are the key steps of the distillation test?

Keep the load path (where forces enter, travel, leave), replace detail with idealized supports, loads and sections, finally state assumptions so the model can be checked.

11
New cards

What are the three common failure modes for machine elements?

Yielding, Fracture or Fatigue

12
New cards

Define the failure mode of Yielding and its properties

Yielding is permanent plastic deformation after unloading and its component remains intact but no longer performs its intended function. It is usually gradual rather than catastrophic.

13
New cards

Define the failure mode of Fracturing and its properties

Complete separation of the component. It can be brittle failure which occurs under negligible plastic deformation and is catastrophic. It can be ductile meaning undergoes extensive plastic deformation and is stable cracks.

14
New cards

Define the failure mode of fatigue and its properties.

This is failure caused by repeated cyclic loading due to repeated stress cycles. It can be repeated/reversed and fluctuating. It forms by crack initiation, then propagation, and final failure.

15
New cards

What is the condition for the Maximum Principle Stress Theory/Mohrs?

The yield strength (Sy) must be greater than the principle stresses

16
New cards

What is the main limitation of the maximum principle stress theory?

It cannot predict failure in ductile materials, where yielding is primarily governed by shear deformation.

17
New cards

What is the condition for the distortion energy theory (von Mises)

Yields if von Mises stress is greater than the yield strength

18
New cards

Which failure theory do we use for each material type?

For brittle materials, we use maximum normal stress theory. For ductile we can use maximum-shear-stress theory and von Mises.

19
New cards

Material Selection: What do the last two digits of carbon represent?

The carbons hundredths of a percent.

20
New cards

How do we quantify low, medium, and high carbon?

Low - 0.05 to 0.30% Carbon, Medium - 0.30 to 0.60% carbon, High 0.60 to 1.0+% Carbon