Ceramics Exam 6

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/124

encourage image

There's no tags or description

Looks like no tags are added yet.

125 Terms

1
New cards

Bronsted Acid

Substance that donates a proton

2
New cards

Bronsted Base

Substance that accepts a proton

3
New cards

Lechatelier’s Principle

Equilibria shifts towards reactants to oppose increase in hydronium, causing decrease in hydroxide

4
New cards

pH

Depends on the concentration of acid/base and its strength (tendency to completely ionize)

5
New cards

Salts

Ionic compounds that can act as an acid or base

6
New cards

Purification with Base

Increase pH until compound of interest dissolves; filter out remaining solids (impurities)

7
New cards

Purification with Acid

Decrease pH until solid of interest precipitates; filter out liquid (washing) to eliminate still-soluble impurities

8
New cards

Acidic Conditions

Particle surface develops a positive charge
MOH + H3O+ → MOH2+ + H2O

9
New cards

Basic Conditions

The particle surface develops a negative charge
MOH + H2O → MO- + H3O+

10
New cards

Point of Zero Charge (PZC)

The pH at which particle surfaces have no charge. PZC = A -B(Z/r)

11
New cards

Stern Layer

Interior layer of immobile ions

12
New cards

Diffuse Layer

Thermally-agitated mobile ions, which adopt a steady-state concentration gradient extending to a distance at which the surface charge is fully compensated

13
New cards

Zeta Potential

The electrical potential at the slipping plane that separates mobile fluid from the fluid layer attached to a dispersed particle in a colloidal dispersion

14
New cards

Isoelectric Point (IEP)

The pH at which the zeta potential goes to zero. IEP = PZC. IEP = particle + stern layer; PZC = particle. Adding acid or base to shift the pH away from the IEP deflocculates the suspension, as indicated by a sharp drop in viscosity

15
New cards

Counterions

Large monovalent counterions allow the diffuse layer to extend greater distances into the liquid, favoring mutual repulsion. Apply a net force pushing the particles apart. Large additions can facilitate charge-compensation over a short distance, compressing the diffuse layer (diminishing returns for acid/base additions)

16
New cards

Homopolymers

May bridge between two polymers, facilitating bridging flocculation (especially when dilute)

17
New cards

Block/Graft Copolymers

Used to overcome bridging flocculation. One part, relatively insoluble in the liquid, anchors onto the particle surface, the other is soluble in the liquid

18
New cards

Theta Temperature

Narrow temperature range. Above which solubility of polymers is enhanced. At lower temperatures, chains are increasingly mutually attracted, collapsing the chains toward the particle surface, impeding steric hinderance

19
New cards

Polyelectrolytes

Polymers with an ionizable group. Effective at forming concentrated deflocculated suspensions

20
New cards

Steric Stabilization

A method used to prevent colloidal particles or nanoparticles from clumping together (aggregation or flocculation) by attaching non-ionic polymers, block copolymers, or surfactants to their surfaces. Dominates at shorter particle separation

21
New cards

Electrostatic Stabilization

A method used to prevent suspended solid or liquid particles in a liquid medium from clumping together. Dominates at larger particle separation

22
New cards

Stable Suspensions

Settle very slowly

23
New cards

Unstable Suspensions

Allow particles to stick on contact, and settle into a loosely-packed mass

24
New cards

Slip Casting

a ceramic forming technique that uses a liquid clay slurry (called casting slip) poured into a porous plaster or gypsum mold to replicate complex shapes

25
New cards

1 Min

Casting time for thin-walled cast of partially coagulated porcelain slurry

26
New cards

1 Hour

Casting time for dense thin-walled cast of sub-micron powder

27
New cards

Coagulated Slip

Casts faster because the cast layer is more water-permeable. Good for liquid-phase sintering

28
New cards

Non-Oxides

Typically sustain oxide surface coatings from handling in air and can be suspended in water as oxides

29
New cards

Molecular Binders

Additives which facilitate particle flow and mutual accommodation during pressing into a shape and provide handling strength to the green pressed body. Generally non-ionic or mildly anionic polymers

30
New cards

PVA (Polyvinyl Alcohol)

Common binder. The polar -OH side group is hydrophillic (water-loving), which promotes dissolution in water, and also fosters interchain bonding. Has a strong affinity for adsorption onto surfaces of oxide particles

31
New cards

PMMA (Polymethlymethacrylate)

Typical binder for non-aqueous suspensions

32
New cards

Plasticizer

Typically added to make the binder deformable at room temperature. Small molecules distributed among the larger binder molecules force the binder chains apart, softening the polymer and effectively reducing Tg

33
New cards

Granules

Purposely-formed particles agglomerates

34
New cards

Direct Granulation

Atomized liquid binder sprayed continuously onto agitated powder. Granule nucleates and grows, particles are added by sticking to binder on the surface. Rubbing and tumbling keep the granule roughly spherical

35
New cards

Spray Drying

A slurry is atomized in a heated dryer. In free-flight (cyclone trajectory) liquid volatilizes from the atomized slurry droplets, forming spherical granules of binder/plasticizer infused particles. Flow into a die

36
New cards

Two-Fluid Nozzle

High-velocity gas (air for water-based slurry) is mixed with slurry to produce turbulance, facilitating droplet formation. The nozzle can spray downward from the top of the chamber or upward, fountain style, from the base. Granule size distribution can be broad, so care must be taken to prevent fine granule gravity segregation

37
New cards

Rotary Nozzle

Slurry flung from channels rotating at high velocity; slurry stream break up into droplets. Granules are uniformly sized. A wider drying chamber is required.

38
New cards

Suspension Additives

Binder, plasticizer, deflocculant (feed slurry and is also continuously mixed), and an anti-foaming agent

39
New cards

Anti-Foaming Agent

Air bubbles degrade the consistency of the spray-dried granules. Stabilized by ionic organics (surfactants)

40
New cards

Donut-Shaped Granules

Can form with high inlet temperature, high binder content, and/or low solids loading. Does not press well. Too hot. Boils too fast

41
New cards

Uniaxial Pressing

A powder compaction technique where loose powder is compressed inside a rigid die cavity along a single vertical axis by one or two punches. Most widely practiced forming process: close tolerances, no drying shrinkage

42
New cards

Single Action

Bottom or top punch

43
New cards

Double Action

Top and Bottom Punch

44
New cards

Floating Die

Emulates double action

45
New cards

Feeding Shoe

Loads granulated powder. Facilitates a high and uniform tap density via head of powder in chute and agitation from multiple passes

46
New cards

(CH3)(CH2)16COOH

Steric acid, an effective lubricant. The carboxyl end is strongly attracted to the oxide particles and die wall, but shear resistance between first adsorbed layer and subsequent layers is low. The lubricant reduces die wear, increases particle packing uniformity, and reduces ejection pressure

47
New cards

Granule Flowability

Inferred from angle of repose

48
New cards

3 Stages of Uniaxial Pressing

  1. Granule Rearrangement

  2. Granule Deformation (eliminating intergranular porosity)

  3. Granule Densification (sliding and rearrangement if individual particles, fracture of aggregates and anisometric particles


49
New cards

Springback

Release of elastic strain. Differential springback of less than 0.75% is desirable for separation of the compact and the punch

50
New cards

End Cap and Ring Cap Defects

Caused by high springback

51
New cards

Lamination Defects

Results from slip-sticking via die wall sticking. Lubrication reduces ejection pressure and tendency for slip-sticking

52
New cards

Slip-Sticking

A spontaneous, jerky sliding motion caused by the difference between static and kinetic friction

53
New cards

Pressure Transmission

A portion of the applied load is transferred laterally to the die wall during compaction. The resisting force from die wall friction results in pressure gradients in the part, in turn resulting in packing density gradients, with pressure and packing density generally decreasing toward the center and with depth in the part. This can lead to warping and cracking defects in the fired part

54
New cards

Pressing Die

May be designed with a split lower punch with spring-loaded regions to equalize pressing pressures. Surface Releif

55
New cards

Isostatic Pressing

A previously-formed part is placed in a rubber or polyurethane bag. The bag is then evacuated around the part and sealed with rubber tape. The bag is then encased in a fluid, and pressurized, which squeezes the part hydrostatically.

56
New cards

Mandrel

Used to isostatically press parts with internal cavities. Made out of tool steel. The surface should have a good polish for release.

57
New cards

Dry-Bag Process

Fluid fills the cavity between steel outer walls and rubber side walls, squeezing a powder compact radially. It is a continuous process for tubular shapes

58
New cards

Extrusion

Geometries uniform in cross-section can be formed with continuous throughput

59
New cards

Extrusion Pastes

Formed using 50 vol% particle loading, binder/plasticizer (polymeric or clay), coagulant (cellulose: converts a slurry to a paste) and 35-50 vol% water

60
New cards

Clay Binder

A fluid suspension is mixed with a high-speed mixer, then filter-pressed into the form of a paste

61
New cards

Polymeric Binder

Powder slurry and spray-dried granules are mixed together to form a paste

62
New cards

Pug Mill

An auger with broken flights kneads (mixes) the feed and forces it through a shredder into an evacuated chamber. Shredded material is small in cross-section and more uniformly de-aired

63
New cards

Batch Operation

Piston extruders

64
New cards

Auger Operation

Auger extruders

65
New cards

Entrance Angle

Determines the extent of differential flow through the tapered die. The taper compresses the mix to accurately adopt the desired shape, but above a critical angle, a region of static materials forms which is a source of defects

66
New cards

Spider

Used to extrude hollow tubes. Attached to the die, and supports the central control rod. Flow streams must join downstream from the spider

67
New cards

Cracks and Lamination

Caused by non-uniform shrinkage during drying. Humidity dryers may be used

68
New cards

Liquid Migration

Caused by excessive extrusion pressures. Causes drying defects

69
New cards

Differential Shrinkage

Caused when anisotropic particles align with the extrusion direction

70
New cards

Surface Craters and Blisters

Caused by exsolved air during decompression. Air may be forced to dissolve in the liquid under extruding pressures

71
New cards

Surface Laminations

Result from slip-stick wall friction

72
New cards

Newtonian

Shear stress is linearly related to the velocity gradient, the constant of proportionality being the viscosity

73
New cards

Shear-Thinning

Solutions which contain long polymer chains and/or supsensions which contain non-attracting anisometric particles can be shear-thinning. With laminar flow, such chains and/or particles can align; as orientation reduces the resistance to shear, the stress required to increase the shear rate by an increment decreases with increasing shear rate. Psuedoplastic. Binder solutions. Particle supsensions can behave as shear-thinning when particle agglomerates are broken up with increasing shear rates. Shear-thinning is preferred as it facilitates a low viscosity during mixing

74
New cards

Shear-Thickening

Moderately-concentrated suspensions containing large agglomerates and/or highly concentrated, well-deflocculated suspensions. Dilatant. In crowded slurries, above a particular shear rate, hindered particle rotation and mutual particle interference may cause the appearance of shear thickening behavior. The onset of dilatant behavior decreases with increasing solids loading. The absence of shear thickening behavior is very important in the pumping and spraying of slurries. Shear thickening fluids are being developed to improve stab/bullet resistance of ballistic fabrics

75
New cards

Bingham Plastic

Slurries containing a linkage of bonded molecules and particles that require a finite stress (yield stress), to initiate flow. Can be shear thinning or shear thickening, such behavior is advantageous when such suspensions are applied as run-resistant coatings

76
New cards

Thixotropic

Shear resistance (apparent viscosity) decreases with shearing time. This phenomenon is typically observed for shear-thinning solutions and suspensions when the orientations of the molecules or particles change with time during shear flow

77
New cards

Rheopectic

Increase in shear resistance with time when sheared at a constant rate. This phenomenon is expected when agitation enhances bonding between structural units in the suspension

78
New cards

Injection Molding

Powder dispersed in an organic fluid is injected into a die. The organic is extracted, leaving a near net-shape ceramic powder compact which is then sintered

79
New cards

Feedstock

Consists of binder and ceramic particles

80
New cards

Components of Binder

Backbone, solvent/plasticizer, and lubrucant

81
New cards

Lubricant

Improves powder wetting to the binder and improves mutual particle sliding

82
New cards

Too Much Binder

Particle-particle contact inadequate for shape retention during binder extraction

83
New cards

Too Little Binder

Air voids in the mix, high viscosity

84
New cards

The Gate

The entry point into the die. It is made of purposefully constricted cross-sectional area, so the mix within it solidifies early, isolating the injection chamber and the die. Die pressure then decreases as the mix solidifies

85
New cards

Weld Lines

Newly-injected jet of mix not bonding well to an older jet of mix. Fixed using a side gate

86
New cards

Thermal De-Binding

Volatilization in inert atmosphere or vacuum, or combustion in air (less residual carbon)

87
New cards

Wicking

Pack the part in fine carbon powder. Low-temperature melting wax is drawn out of the part by capillary action. Powder and high-temperature-melting binder provide support against slumping.

88
New cards

Solvent Extraction

Part is immersed in a liquid in which one of the binders is soluble

89
New cards

Low Solids Loading

Causes particles to migrate together during thermolysis. Porosity between these agglomerates can cause cracks to form before and/or after sintering

90
New cards

Too Rapid Thermal Binder Extraction

Can lead to bloating of the part via released gases. Initial binder extraction must be slow. When pore channels are opened, heating can be more rapid

91
New cards

Voids

Decrease solids loading

92
New cards

Short Shots

Fixed by increasing feedstock temperature to prevent premature freezing of the gate

93
New cards

Flashing

Excessive pressure forces mix into the seam between the mold halves

94
New cards

Resistance Temperature Detectors (RTDs)

Transduce temperature via resistance

95
New cards

Thermocouples

Transduce temperature via voltage.

96
New cards

Thermistors

Transduce temperature via resistance. Usually inexpensive ceramic compounds. More sensitive, more limited temperature range, less stable, and less precise than RTDs. Typically epoxy-coated and quite small, so that they can quickly reach thermal equilibrium with the medium they are measuring

97
New cards

Themistor Resistance

RT = RB(VT/V0-VT)

98
New cards

Seebeck Voltage

The potential difference between two points of different temperature along the wire

99
New cards

E, J, T, and K Thermocouples

Combinations of oxidation-resistant, relatively inexpensive metal alloys. They have comparatively high voltage change per unit temperature change (high signal to noise ratio), but their maximum temperatures are limited due to oxidation degredation

100
New cards

R, S, and B Thermocouples

Platinum-based thermocouples. More expensive, have a lower voltage change per unit temperature change, but can be used at higher temperatures in an oxidizing environment.