1/60
Comprehensive review flashcards covering key concepts from lecture exams on heavy-duty and automotive electrical systems, starting/charging systems, circuit laws, sensor operations, and networking.
If voltage is held constant in a circuit, amperage increases if resistance decreases and amperage decreases if resistance increases. What law does this relationship demonstrate?
Ohm's law
Under what condition do galvanic reactions take place between two dissimilar metals?
When they are placed in an electrolyte
How do sensors, which are low-voltage electronic devices, differ from sending units?
Sensors have no moving parts
What is the fundamental concept of electricity?
The flow of electrons from atom to atom
What vehicle indicator light operates based on the principle of voltage drop?
Charging system indicator light
Which electrical measurement quantifies how many electrons are in movement at one time?
Amperage
In an alternator, which component generates the magnetic field?
The rotor
What test is performed to measure a battery's capacity?
Conductance test
What device uses electromagnets to close contacts and act like an electrical switch?
A relay
What component is placed at each end of the J-1939 CAN-bus to minimize signal distortion?
A terminating resistor
Which parameter measures a signal applied to devices operating at a varying frequency interval?
Pulse width
If a starter motor spins freely but fails to crank the engine, what is the most likely mechanical fault?
Pinion slipping
Which layer of network architecture defines how the network hardware is constructed?
Physical layer
Variable reluctance sensors are two-wire sensors primarily used to measure what parameter?
Rotational speed
Why does an instrument cluster illuminate warning bulbs for several seconds during key-on engine off or cranking?
To perform a prove-out sequence and validate the correct operation of each warning light
What is the phenomenon where reversing the direction of current flow in a conductor causes a motor to rotate in the opposite direction called?
Motor effect
Which starting system circuit prevents the starter motor from engaging while the engine is running?
Automatic disengagement lockout
In an electronic control system, what are the functions performed by electrical signals produced by the processor called?
Outputs
What test is conducted on the positive alternator cable to detect excessive resistance between the alternator and the batteries?
Alternator cable voltage drop test
What are thermistors?
Temperature-sensitive variable resistors
Which component of a starter motor consists of heavy copper segments insulated from each other and from the armature shaft?
Commutator
Which headlight systems utilize an electric arc rather than a glowing filament to generate light?
High-intensity discharge (HID) lamps
On what starter component are the resistance and current draw of the pull-in and hold-in windings evaluated?
Starter solenoid
Which alternator component controls the strength of the rotor's magnetic field to regulate electrical output?
Voltage regulator
Why must an ammeter be connected in series by breaking the circuit when measuring current?
To ensure that all circuit current flows directly through the meter
In a parallel circuit with multiple pathways for current, how are all loads connected relative to the voltage supply?
All components are connected directly to the voltage supply
What term identifies the small amount of magnetic flux remaining in an alternator rotor after coil excitation ceases?
Residual magnetism
What type of switch acts as an overcrank protection device in a cranking circuit?
Thermal protection switch
How must circuit protection devices such as fuses, fusible links, and circuit breakers be wired relative to their loads?
In series
How many paths exist for current flow in a series circuit containing multiple loads?
Only one path
Through what parts are field coils connected in series with the armature windings inside a starter motor?
Starter brushes
In electrostatic theory, how do negative charges behave in the presence of positive charges?
Negative charges are attracted to positive charges
Which test tool is used to verify the resistance of the J-1939 data bus when troubleshooting network faults?
An ohmmeter
In automotive electronic sensor circuits, what is the standard value for reference voltage (Vref)?
5volts
What type of electrical components convert electrical energy from current flow into other forms of energy?
Loads
What items are placed between the starter solenoid and housing to properly adjust pinion clearance?
Shims
What process converts alternating current (AC) produced by the stator into direct current (DC)?
Rectification
Variable reluctance sensors and galvanic sensors are grouped together as examples of what sensor category?
Voltage-generating sensors
What component must always be tested first when diagnosing problems in a vehicle's charging system?
The battery (or batteries)
What term defines the voltage reference point utilized by an alternator to adjust and regulate output?
Sensing
Why can an ohmmeter only be used to locate continuity faults when the circuit is completely unpowered?
Connecting an ohmmeter into a live, powered circuit causes inaccurate readings and can damage the meter's internal circuitry
Why are communication wire pairs twisted together along harness runs?
To minimize electromagnetic interference caused by external magnetic fields and radio waves
What direct measurement is used to locate excessive resistance in high-amperage circuits during operation?
Voltage drop
What is generally an unwanted by-product of electrical resistance in a circuit?
Heat
Electronic service tools connect to what diagnostic port to scan for network communication faults?
Data link connector (DLC)
What opposition develops in the stator windings to counteract increasing current induced by the spinning rotor?
Counter-electromotive force (CEMF)
In a photoresistor, how does resistance change in response to an increase in ambient light?
Resistance decreases
If an engine cranks slowly or fails to turn over during starting checks, what battery-side issue is commonly responsible?
Battery cables that are too small or have poor, corroded connections
What term describes the total opposition to alternating current (AC) flow, combining resistance and reactance?
Impedance
In the American Wire Gauge (AWG) numbering system, what happens to the physical wire diameter as the gauge number increases?
The wire diameter decreases
Which unit is used to measure light intensity and total luminous output?
Lumen
What starting mechanism multiplies torque delivered to the pinion gear by interposing intermediate gears between the armature and drive mechanism?
Gear reduction
If an alternator's current output fails to rise when full-fielded, what component is defective?
The rectifier bridge (shorted, open, or grounded)
Which alternator components are housed internally such that the alternator must be disassembled to access or replace them?
Brushes
What network symptoms occur if the CAN bus terminating resistors are missing or damaged?
Network signals become distorted and transmission speed is degraded
Which circuit protection devices can be manually or automatically reset after interrupting an overcurrent condition?
Circuit breakers
In electromagnetic induction, what induced property changes proportionally when the magnetic field strength varies?
Voltage
If instrument cluster gauges fail to execute a prove-out sweep upon key-on, what electrical defect is typically present?
A poor, loose, or resistive ground connection
How are two batteries oriented when they are wired together in series?
Connected in line with each other, with the positive terminal of one connected to the negative terminal of the other
Which signal parameter quantifies the on-time duration of an electrical output operating at a fixed frequency?
Pulse width
What circuit condition allows an alternator to produce high amperage output?
Low circuit resistance