1/60
Essential technical vocabulary and definitions covering heavy transport engineering, specialized logistics, marine transport, wind turbine operations, and structural strength analysis.
Heavy transport
The movement of exceptionally heavy or oversized loads using specially designed vehicles and engineered transport methods.
Abnormal load transport
The road transport of a load that exceeds normal legal limits for dimensions or weight.
Project cargo
Large, heavy or complex cargo that requires project-specific engineering, handling and logistics.
Route survey
A systematic inspection of a proposed route to identify geometric, structural and operational constraints.
Clearance envelope
The space that must remain free of obstacles for a vehicle and its load to pass safely.
Slewing envelope
The area occupied by a rotating crane superstructure or other slewing equipment.
Centre of gravity
The point at which the resultant weight of a body may be considered to act.
Allowable ground bearing pressure
The maximum contact pressure that the ground or supporting surface may safely withstand.
Self-propelled modular transporter (SPMT)
A modular, hydraulically suspended transporter with its own drive and steering, configurable in multiple axle-line combinations.
Well-type bridge trailer (Kesselbrücke)
A heavy-haul trailer arrangement with a lowered central section between front and rear support units, used for very tall or heavy loads.
Strand jack
A hydraulic lifting device that grips and pulls multiple high-strength steel strands in repeated strokes to raise or lower a heavy load.
Air-caster system
A system that uses a thin film of compressed air to move heavy loads with very low friction over a suitable floor.
Spreader beam
A lifting beam used to distribute forces between lifting points and control sling angles.
Below-the-hook lifting device
A device attached between the crane hook and the load to facilitate lifting, such as a lifting beam or grab.
Crab steering
A steering mode in which all wheels are turned in the same direction so the vehicle moves diagonally or sideways.
Positive fit
A securing method in which the load is restrained by direct contact with fixed structures or blocking elements.
Frictional restraint
A securing method in which friction between the load and its support is increased, usually by applying pre-tension through lashings.
Standard tension force (STF)
The residual force in a lashing after the tensioner handle has been released, as defined for the relevant equipment.
Dunnage
Material such as timber, rubber or steel used to support, separate or secure cargo during transport or stowage.
Load-out
The engineered transfer of heavy cargo from a quay or fabrication site onto a barge or vessel.
Float-on/float-off (Flo-Flo)
A method in which a semi-submersible vessel is ballasted down so that floating cargo can be moved on or off.
Sea fastening
A structural arrangement that secures cargo to a vessel and prevents movement under marine accelerations.
Ballasting
The process of taking water into or pumping water out of ballast tanks to control a vessel's draught, trim and stability.
Metacentric height (GM)
A measure of a vessel's initial transverse stability, defined by the distance between its centre of gravity and metacentre.
Significant wave height
The average height of the highest one-third of waves over a specified observation period.
Pitch
The rotational movement of a vessel about its transverse axis, causing the bow and stern to rise and fall.
Intact stability
The ability of a vessel to remain stable in its undamaged condition under the specified loading conditions.
Wind turbine generator (WTG)
A wind turbine together with its generator and associated systems for producing electricity.
Nacelle
The housing at the top of the tower containing the generator, gearbox where fitted, and other drive-train components.
Blade lifter
A specialised lifting or transport device used to raise and position a wind turbine blade.
Pitch system
The mechanism that rotates each blade about its longitudinal axis to control aerodynamic loading and power output.
Monopile
A large-diameter steel tubular foundation driven or installed into the seabed to support an offshore wind turbine.
Transition piece
A structural component connecting an offshore foundation, such as a monopile, to the wind turbine tower.
Jacket foundation
A lattice-frame offshore foundation supported by piles driven into the seabed.
Marshalling port
A port where wind turbine components are received, stored, inspected and prepared for offshore installation.
Jack-up installation vessel
A vessel that raises itself above the water on legs to provide a stable platform for offshore lifting operations.
Finite element method (FEM)
A numerical method that divides a structure into elements to calculate its response to loads.
Finite element analysis (FEA)
A numerical simulation used to evaluate stresses, strains, displacements or other structural responses.
Stress
The internal force per unit area within a material, usually expressed in pascals or megapascals.
Equivalent stress
A single stress value, often von Mises stress, used to assess a multiaxial stress state against a material yield criterion.
Notch effect
The increase in local stress caused by a geometric discontinuity such as a hole, groove or sharp corner.
Yield strength
The stress at which a material begins to deform plastically to a specified extent.
Tensile strength
The maximum tensile stress a material can withstand before fracture.
Young's modulus
A material property describing the relationship between elastic stress and strain.
Poisson's ratio
The ratio of transverse strain to axial strain under uniaxial loading.
Dynamic amplification factor
A factor accounting for dynamic effects such as impact, acceleration or vibration.
Fatigue
Progressive damage caused by repeated or fluctuating loading, potentially leading to cracking.
Plate buckling check
A verification that a plate or thin-walled element will not buckle locally under compression or shear.
Bearing failure
A local failure mode in which the material around a bolt or pin hole is crushed or deformed.
Tear-out failure
Failure in which material tears from an edge or hole under tensile or shear loading.
Load spectrum
A description of the magnitude and frequency of loads experienced during a component's service life.
Section modulus
A geometric property of a cross-section used to calculate bending stress.
Second moment of area
A geometric property describing a cross-section's resistance to bending.
Mesh convergence
A check that the calculated result becomes sufficiently stable as the finite-element mesh is refined.
Load chart
A manufacturer's chart showing the permissible lifting capacity of a crane for defined configurations and radii.
Utilisation
The ratio of the applied demand to the available design capacity, often expressed as a percentage.
Couple
A pair of equal and opposite parallel forces separated by a distance, producing a pure moment.
Plastic hinge
A localised zone in a member where plastic rotation can occur after the bending resistance is reached.
Non-destructive testing (NDT)
Inspection methods that assess a component without damaging it, such as ultrasonic or magnetic-particle testing.
Ultrasonic testing (UT)
A non-destructive inspection method that uses high-frequency sound waves to detect internal flaws.
Magnetic particle testing (MT)
A non-destructive inspection method used to detect surface and near-surface flaws in ferromagnetic materials.