Ch 7, 8, 9 Materials

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/34

encourage image

There's no tags or description

Looks like no tags are added yet.

35 Terms

1
New cards

Edge dislocation

  • extra half-plane of atoms inserted into crystal lattice

  • Burgers vector is perpendicular to dislocation line


2
New cards

Screw dislocation

  • burgers vector is parallel to dislocation line


3
New cards

FCC slip systems

12 slip systems

(4 non-parallel {111} planes * 3 non-parallel <110> directions)

close-packed planes and close-packed directions make it very ductile


4
New cards

BCC slip systems

12 slip systems

slip strongly temperature dependent → ductile-to-brittle transition

5
New cards

HCP slip systems

fewer slip systems

makes it more brittle than FCC or BCC

6
New cards

Resolved shear stress

occurs when shear stress resolved along slip plane and direction reaches a critical threshold:

τRss=σcos⁡ϕcos⁡λ\tau_{\text{Rss}} = \sigma \cos\phi \cos\lambda

  • σ\sigma = Applied tensile (or compressive) stress

  • ϕ\phi = Angle between the normal to the slip plane and the applied load direction

  • λ\lambda = Angle between the slip direction and the applied load direction

  • Schmid Factor (m): m=cos⁡ϕcos⁡λm=\cos\phi\cos\lambda . A higher Schmid factor means yielding occurs at a lower applied stress


7
New cards

Grain size reduction (Hall-Petch strengthening)

more grain boundaries act as barriers to dislocation motion

  • reducing average grain diameter increases total grain boundary surface area per unit volume (creates more barriers per unit distance and increases yield strength → Hall-Petch equation)


8
New cards

Strain hardening (cold work)

Deforming a ductile metal below its recrystallization temperature (cold work) increases its strength and hardness

  • mutual repulsion of dislocations severely restricts further dislocation, increasing yield strength and tensile strength while reducing ductility


9
New cards

Solid solution strengthening

Alloying a pure metal with impurity atoms strengthens the host lattice

(impurity atoms create local lattice strain fields that interact with and block dislocation movement)

  • Higher applied stress is required to break dislocations free from these impurity strain fields and move them through the distorted lattice


10
New cards

Recovery

reduction of dislocation density and annihilation of point defects via thermal diffusion

11
New cards

Grain growth

at elevated temperatures, larger grains grow at the expense of smaller ones to minimize total grain boundary surface energy

12
New cards
<p>Ductile fracture</p>

Ductile fracture

characterized by significant plastic deformation, slow crack propagation, and “cup-and-cone” fracture

<p>characterized by significant plastic deformation, slow crack propagation, and “cup-and-cone” fracture</p>
13
New cards

Brittle fracture

rapid crack propagation with little to no plastic deformation

14
New cards

Fatigue failure

  • Failure under fluctuating/cyclic stresses well below the static yield strength.

  • S-N Curve: Plots stress amplitude (S) versus cycles to failure (N) on a logarithmic scale.


15
New cards

Fatigue Limit (Endurance Limit)

A maximum stress amplitude below which fatigue failure will never occur, regardless of the number of cycles (common in steels and titanium alloys)

16
New cards

Creep deformation

Time-dependent permanent deformation under a constant static load at elevated temperatures

17
New cards

Primary (Transient) Creep

Creep rate decreases with time due to strain hardening

18
New cards

Secondary (Steady-State) Creep

The creep rate (Δϵ/Δt\Delta \epsilon / \Delta t ) is constant and minimal, maintained by a dynamic balance between strain hardening and thermal recovery processes

19
New cards

Tertiary Creep

Creep rate accelerates rapidly up to catastrophic failure due to microstructural damage (void formation, grain boundary separation, necking)

20
New cards

Composition conversions

C1=(C1′A1C1′A1+C2′A2)100C_1 = \left( \frac{C_1' A_1}{C_1' A_1 + C_2' A_2} \right) 100

21
New cards

Lever Rule

Wα=Cβ−C0Cβ−CαW_\alpha = \frac{C_\beta - C_0}{C_\beta - C_\alpha} , Wβ=C0−CαCβ−CαW_\beta = \frac{C_0 - C_\alpha}{C_\beta - C_\alpha} ,

  • Locate the alloy composition (C0C_0) and temperature point on the phase diagram

  • Draw a horizontal tie-line at that temperature across the two-phase field

  • Read the composition of the phase on the left boundary (CαC_{\alpha}) and the right boundary (CβC_\beta) where the tie-line intersects the phase boundaries

  • Apply the lever rule formula: the fraction of a phase is the length of the opposite lever arm divided by the total tie-line length


22
New cards

Zero Schmid Factor (m = 0)

If either cos⁡ϕ=0\cos\phi = 0 (the load lies entirely in the slip plane, perpendicular to the normal) or cos⁡λ=0\cos\lambda = 0 (the load is perpendicular to the slip direction), then m=0m = 0 , meaning no resolved shear stress acts on that system, and it cannot be activated.

23
New cards

FCC interplanar spacing (d) (can be calculated)

a3\frac{a}{\sqrt3}

24
New cards

FCC burgers vector (b)

b=a2b=\frac{a}{\sqrt2}

25
New cards

BCC interplanar spacing (d)

a2\frac{a}{\sqrt2}

26
New cards

BCC burgers vector (b)

3a2\frac{\sqrt3a}{2}

27
New cards

Atomic mechanism of grain size reduction

  • Crystallographic Misalignment: Adjacent grains have different crystallographic orientations, so a dislocation moving along a slip plane in one grain must change direction to cross into the next grain.

  • Atomic Disorder: The atomic mismatch at grain boundaries creates a discontinuity in the slip planes


28
New cards

Atomic mechanism of strain hardening (cold work)

  • Dislocation Multiplication: As plastic deformation proceeds, the number of dislocations in the material increases (increasing dislocation density)

  • Dislocation Entanglement: As the distance between dislocations decreases, their individual strain fields overlap and interfere with each other. Dislocations on intersecting slip planes run into one another, forming "traffic jams" and tangles


29
New cards

Atomic mechanism of solid solution strengthening

  • Lattice Strain Fields: Solute atoms that differ in size from the host atoms introduce localized lattice strains—smaller impurity atoms create tensile strains, while larger impurity atoms create compressive strains.

  • Dislocation Pinning: These strain fields interact with the strain fields surrounding dislocations. Solute atoms migrate toward dislocations to cancel out local lattice strains, effectively "pinning" or anchoring the dislocations


30
New cards

finding cos for shear stress

a⋅b=∣a∥b∣cos⁡(θ)→cos⁡(θ)=[u1⋅u2+v1⋅v2+w1⋅w2(u12+v12+w12)⋅(u22+v22+w22)]a\cdot b=\left|a\Vert b\right|\cos\left(\theta\right)\to\cos\left(\theta\right)=\left\lbrack\frac{u_1\cdot u_2+v_1\cdot v_2+w_1\cdot w_2}{\sqrt{\left(u_1^2+v_1^2+w_1^2\right)}\cdot\sqrt{\left(u_2^2+v_2^2+w_2^2\right)}}\right\rbrack

(for direction 1 [u1v1w1]\left\lbrack u_1v_1w_1\right\rbrack and direction 2 [u2v2w2]\left\lbrack u_2v_2w_2\right\rbrack )

31
New cards

ϕ\phi

ϕ\phi = angle between applied stress and normal to slip plane

32
New cards

λ\lambda

λ\lambda = angle between applied stress and slip direction

33
New cards

Internal (center) crack length

a = length/2

34
New cards

Surface (edge) crack

a = length

35
New cards

Why does grain growth occur at elevated temperatures?

Decreases internal energy (fewer grain boundaries)