1/49
Looks like no tags are added yet.
What is the purpose of an engine?
Is to convert the heat energy of burning fuel into mechanical energy.
What is mechanical energy used for?
Propel the vehicle, power the air-conditioning system and power steering, and produce electrical power for use through the vehicle.
Comnbustion
The rapid burning of the air-fuel mixture in the engine cylinders, creating heat and pressure.
Internal combustion engine
Engine combustion occurs within the power chamber, such as automobiles.
External Combustion engine
Burns fuel outside of the engine itself, such as a steam engine.
Combustion chamber
The space left withing the cylinder when the piston is at the top of its combustion chamber.
Mechanical Force
The pressure developed within the combustion chamber is applied to the head of a piston to produce a usable mechanical force.
Mechanical power
Power is the rate at which work is done.
Block
The foundation of any engine. All other parts are either directly or indirectly attached to the block of an engine.
What are cylinder heads constructed of?
Cast iron or aluminum
What are intake manifolds constructed of?
Nylon-reinforced plastic or aluminum.
What are exhaust manifolds constructed of?
cast iron or steel tubing
Thermostat
Controls the temperature in the cooling system.
Oil galleries
Passages that allows oil to flow to the crankshaft and block.
Fuel tank
Where fuel is stored and where most fuel pumps are located
Fuel Filter and lines
Which transfer the fuel from the fuel tank to the engine
Fuel injectors
Which spray fuel into the intake manifold or directly into the cylinder, depending on the type of system used.
Spark plugs
Provide an air gap inside the cylinder where a spark occurs to start combustion
Sensor(s)
Include crankshaft position (CKP) and camshaft position (CMP) sensors, used by the powertrain control module (PCM) to trigger the ignition coil and the fuel injectors
Ignition Coil
Increase battery voltage to 5,000 to 40,000 volts
Ignition control module (ICM)
Controls when the spark plug fires
Associated wiring
Electrically connects the battery, ICM, coil, and spark plugs.
Four-stroke cycle
An internal combustion engine design where four strokes of the piston are required to complete one cycle of event.
Who developed the first four stroke cycle?
German engineer, Nickolaus Otto in 1876
Cylender
A piston chamber in a internal combustion engine.
Intake stroke
The intake valve is open and the piston inside the cylinder travels downward, drawing a mixture of air and fuel into the cylinder. The crankshaft rotates from TDC to BDC
Compression stroke
As the engine continues to rotate, the intake valve closes and the piston moves upward in the cylinder, compressing the air-fuel mixture. The crankshaft rotates from BDC to TDC.
Power stroke
When the piston gets near the top of the cylinder, the spark at the spark plug ignites the air-fuel mixture, which force the piston downward. The crankshaft rotates from TDC to BDC.
Exhaust stroke
The exhaust valve open, and the piston forces the residual burned gases out of the exhaust valve, and into the exhaust manifold and exhaust system. The crankshaft rotates from BDC to TDC.
Engines are classified by
Number of strokes, cylinder arrangement, longitudinal and transverse mounting, valve and camshaft number and location, type of fuel,cooling method and type of induction pressure.
Pancake or Boxer
An engine arranged for compactness by stacking cylinders one above another horizontally or side by side.
Single overhead camshaft (SOHC)
When one overhead camshaft is used
Double overhead camshaft (DOHC)
When two overhead camshaft are used.
Naturally aspirated
If atmospheric air pressure is used to force the air-fuel mixture into the cylinders
Supercharger
Is an engine drive air pump that supplies more than the normal amount of air into the intake manifold and boosts engine torque and power
Rotary engine
Has a rotating combustion chamber and has a triangular- shaped rotor turning in a housing. The housing is in the shape of a geometric figure called a 2 lobed epitrochoid. A seal on each corner, or apex, of the rotor is in constant contact with the housing, so the rotor must turn with an eccentric motion.
Principal end
The end of the engine that the flywheel is attached to
Nonprincipal end
Is generally referred to as the front of the engine, where the accessory belts are used.
Bore
The diameter of a cylinder.
Displacement
The total volume displaced or swept by the cylinders in an internal combustion engine
Compression Ratio (CR)
The ratio of the volume in the engine cylinder with the piston at BDC to the volume at TDC.
Stroke
is the distance the piston travels from TDC to BDC
If compression is lower
Lower power
Poorer fuel economy
Easier engine cranking
More advance ignition timing possible without spark knock (detonation)
If compression is higher
Higher power possible
Better fuel economy possible
Harder to crank engine, especially when hot
Less ignition timing required to prevent spark knock
Head gasket thickness
A thicker than stock gasket will decrease the compression ratio and a thinner than stock gasket will increase the compression ratio
Increasing the cylinder size
If the bore or stroke is increased, a greater amount of air will be compressed into the combustion chamber, which will increase the compression ratio.
Torque
Is the term used to describe a rotating force that may or may not result in motion.
Power
The rate of doing work
Horsepower
Is always expressed with the rating and the engine speed where the maximum power was achieved.
How much does a nonsupercharged or no turbocharged looses for every 1,000ft of altitude?
3% of its power