Properties LAB Exam

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/28

encourage image

There's no tags or description

Looks like no tags are added yet.

29 Terms

1
New cards

1.1 Tensile Strength of Steel

OBJECTIVE: To determine what kind of steel you have with tensile strength

Machine used: Tension Testing machine

Steps:

1. Measure the center diameter of rod to nearest 0.001in

2. Mark gauge length, it should be equidistant and near the middle

3. Grip specimen at sections outside the gauge length

4. Apply load at constant rate

5. Measure extensions at predetermined load intervals

6. When increase in load stops, record the load, this is the yield point

7. If yield is not noticed, use offset to determine

8. Plot stress strain diagram

9. Calculate tensile strength (max load/area)

10. Calculate elongation over gauge length and percentage increase

2
New cards

1.2 Compressive Strength of Wood Parallel to the Grain

4x4x12in Wood

Objective: Find compressive Strength of a wood sample

Machine Used: Gilson Compression Machine

Steps:

1. Make sure end of specimen is level

2. Position specimen under crosshead of testing machine

3. Apply load at 0.024in/min

4. Continue loading past proportional limit

5. Read deformation to the 0.0001in

3
New cards

1.3 Modulus of Rupture of Lumber

2x4x12in Wood

Objective: Find tensile strength of a wood sample from flexural test

Machine Used: Gilson Compression Machine

Steps:

1. Measure cross-sectional area of wood

2. Position specimen on support with a span length of 18in

3. Apply load at center of specimen at 0.1in/min

4. Continue adding load until failure

5. Write maximum load and type of failure

6. Draw moment diagram for failure and calculate modulus of rupture

4
New cards

2.1 Materials Finer than 0.075 (No. 200) Sieve by Washing

2500g of aggregates

Objective: Measure the percentage of dust that is in the aggregates, AKA determine how clean the aggregates are

Steps:

1. Record dry mass of aggregate

2. Stack sieves with No. 200 at the bottom

3. Put aggregates in bucket and fill with water until water covers aggregate

4. Mix aggregates

5. Pour contents in bucket over sieves

6. Repeat until water is clear

7. Place clean aggregates into a pan

8. Place pan in oven to dry overnight.

9. Record weight of aggregates after drying

5
New cards

2.2 Specific Gravity and Absorption of Coarse Aggregate

2500g of aggregates

Objective: Determine specific gravity and absorption of coarse aggregates

Steps:

1. Make aggregates into Saturated Surface Dry condition by drying with towel

2. Weigh SSD aggregates

3. Place aggregates in wire basket and attach to hook (make sure to tare scale before adding aggregates)

4. Record weight of aggregates underwater

5. Empty aggregates in pan and oven dry overnight

6. Record mass of aggregates after drying

7. Determine Bulk Specific Gravity with calculations

6
New cards

2.3 Percent Solids and Voids in Concrete Aggregates

Objective: Determine unit weight of aggregates in concrete

Steps:

1. Measure weight of empty bucket

2. Fill bucket 1/3 full, rod aggregates 25x

3. Fill bucket 2/3 full, rod aggregates 25x

4. Fill bucket 3/3 full, rod aggregates 25x

5. Level the bucket surface

6. Weight bucket with aggregates and find net weight (bucket + agg - empty bucket)

7
New cards

2.4 Sieve Analysis of Fine Aggregates

Objective: Determine gradation curve of fine aggregate sample

Machine used: Mechanical Shaker

Steps:

1. Clean and stack sieves, largest opening at the top and smallest opening at the bottom

2. Weight dry aggregates

3. Pour aggregates into sieve

4. Place stack in mechanical shaker for 10mins

5. Remove stack from shaker and separate sieves, weigh mass sieve and aggregates

6. Clean and re-stack

8
New cards

3.1 Sand Equivalent

Objective: Used to find abundance of sand and clay in a sample of fine aggregates

Machine Used: Mechanical Shaker

Steps:

1. Pour sand in cylinder using funnel

2. Using a metal tube, add Calcium Chloride to cylinder. With a twisting motion, agitate the sand at the bottom to mix sand.

3. Add Calcium Chloride until 15inch mark

4. Let mixture stand for 10mins

5. Put stopper on cylinder and invert several times

6. Place cylinder in mechanical shaker for 45 seconds then let rest for 20mins

7. Record top level of sample for clay reading

8. Place weighted foot assembly into cylinder and read top mark of white circle. Subtract 10in to determine the height of the sand

9
New cards

3.2 LA Abrasion Test

Objective: Determines the hardness of aggregates

Machine Used: Los Angeles Testing Machine

Steps:

1. Weigh aggregates

2. Place aggregates into LA Machine with eleven 1 pound metal balls

3. Close lid and rotate for 500 revolutions at 30rpm

4. Take out steel balls and aggregates from machine

5. Sieve aggregates through #12 sieve and separate aggregates retained and passing

6. Wash retained aggregates until water runs clear (to get rid of dust)

7. Dry in oven and record clean retained aggregate

8. Total mass - retained = aggregates passing through #12 sieve

9. Divide mass passed through #12 sieve by total mass to obtain LA abrasion number

10
New cards

3.3 Fine Angularity

Objective: Determine uncompacted void content of fine aggregate material

Steps:

1. Place desired weight of each aggregate into a pan. Tare after each aggregate

2. Mix aggregates until homogenous

3. Pour aggregate into funnel (plug end with finger)

4. Level aggregates in funnel and release finger to let aggregate fall into cylinder

5. Level cylinder with spatula and tap sides of cylinder

6. Put pan on scale and tare

7. Place aggregates into pan and record weight

11
New cards

3.4 Specific Gravity and Absorption of Fine Aggregates

Objective:

Steps:

1. Place damp sand on pan

2. Use a hair dryer to obtain Saturated Surface Dry condition

3. Place cone on pan with the sand

4. Scoop sand into the cone until 1/3 full, tamp 25x

5. Fill 2/3 full, tamp 25x

6. Fill 3/3 full and tamp 25x

7. Clear sand around the cone

8. Remove cone and observe slump if cone stays intact, dry sand more. If cone falls, SSD has been achieved

9. Fill pycnometer with water to calibration line and weigh to determine mass

10. Partially remove water and add 500g if aggregates

11. Rinse side of flask to push aggregate to the bottom

14. Fill flask with water to fill line and rotate flask to get rid of air bubbles

15. Measure mass of flask + aggregates

16. Place all contents in pan, make sure all particles are in pan

17. Place pan in oven and weight dry aggregates

12
New cards

4.1 Normal Consistency of Hydraulic Cement

Objective: Determine the water/cement ratio of cement paste

Instrument Used: Vicat Apparatus

Steps:

1. Add mixing water to a bowl and 650g of cement paste. Let it sit for 30 seconds. turn on mixer at low speed for 30sec, scrape sides. Mix at medium speed for 1min

2. Using gloved hands gather paste and make a sphere. Place sphere in mold and push inside. Cut excess material from the top. Place mold on glass and put under Vicat apparatus

3. Move plunger to right above cement surface and adjust indicator to 0mm. Release rod and measure penetration after 30 secs.

13
New cards

4.2 Time of Setting of Hydraulic Cement with Vicant Apparatus

Objective: Determine normal or standard consistency of cement paste

Instrument used: Vicant Apparatus

Steps:

1. Use sample created in 4.1 or create sample like in 4.1

2. Place needle on surface of cement paste and adjust indicator to 0mm

3. Release rod and measure penetration

4. Repeat test every 15mins until 25mm penetration is achieved

14
New cards

4.3 Blaine Fineness Test

Objective: Determine fineness of cement

Instrument used: Blaine Apparatus

Steps:

1. Measure 3g of cement

2. Place metal disk and filter paper in capsule

3. Place 3g of cement in capsule and filter paper on top of cement, compact sample

4. Put cap on capsule and apply grease on outside to ensure air tightness. Place capsule in apparatus

5. Remove air by using pump. Manometer liquid must touch top mark before closing valve

6. Remove cap and let fluid go down to the second mark. Start the timer once it crosses second mark and stop once fluid reaches third mark

15
New cards

5.1 Mixing of Concrete

Objective: Make a concrete sample for testing

Machine used: Concrete mixer

Steps:

1. Weigh cement, coarse aggregates, water, and sand

2. To a concrete mixer, add coarse aggregates and sand (let mix for 30sec)

3. Turn on mixer and add cement and water. Let mix for 3mins, rest 3mins, and mix for 2mins

4. Empty concrete mix onto a tray

16
New cards

5.2 Slump Test

Objective: Measures consistency of fresh concrete to determine workability

Steps:

1. Place fresh concrete (within 5mins of finished mixing) into cone

2. Fill cone 1/3 and dry rod 25x

3. Fill cone 2/3 and dry rod 25x

4. Fill cone 3/3 and dry rod 25x

5. Level surface by rolling rod on top and remove cone slowly

6. Flip cone upside down beside concrete, place rod on top of cone

7. Measure from top of concrete surface to rod

17
New cards

5.3 Air Content by Pressure Method

Objective: Obtain air content by using pressure meter

Instrument used: Air meter (type B)

Steps:

1. Fill container with concrete in three layers and tamp each layer 25x

2. Tap perimeter of mold 15x with mallet

3. Make top smooth with rod

4. Place lid and clamp onto container with open petcock valves

5. Use rubber injector and fill one petcock with water until all air is out

6. Close petcocks

7. Pump air into container

8. Release lever and read guage

9. Record content

18
New cards

5.4 Measuring Temperature of Freshly Mixed Concrete

Objective: Measure temperature of fresh concrete

Instrument used: Thermometer

Steps:

1. Place thermometer in freshly mixed concrete

2. Leave thermometer for 2 mins or until temperature stabilizes and record

*must be done 5 mins after concrete is done mixing

19
New cards

6.1 7-Day Flexural Strength by Simple Beam 3rd Point Loading

Objective: Measured tensile strength through flexural test third point loading

Machine Used: Gilson Compression Machine

Steps:

1. Measure length, width, and height of beam

2. Place beam in compressive strength device

3. Ensure third point loading on beam (there are two points that force is applied which makes conc. split in the middle

4. Input beam diameter in computer

5. Slowly add load until beam reaches failure

6. Record load at which beam failed

20
New cards

6.2 Mixing of Hydraulic Cement Mortars

Objective: Make a mortar sample for testing

Steps:

1. Add water and cement to mixing bowl

2. Turn on mixer at slow speed for 30 seconds

3. While still mixing, add sand into bowl

4. Mix at medium speed for 30seconds

5. Scrape sides and paddle and let stand for 1min 30sec and cover with lid

6. Mix again at medium speed for 1min

7. Pour 1inch of mixture into greased mold and tamp 20x

8. Fill rest of mold and tamp 20x

9. Level top with spatula

10. Put lids on and place in curing room for 7 days.

21
New cards

7.1 Compressive Strength of Hydraulic Cement Mortars

Objective: Determine compressive strength of mortar sample

Machine used: Gilson Compression Machine

Steps:

1. Remove cement blocks from mold and choose the best sample out of the three (least defects)

2. Place best sample into compression machine

3. Slowly apply load until sample fails

4. Record Maximum load

22
New cards

8.1 28 Day Compressive Strength of Concrete + ANOVA analysis

Objective: test the compressive strength of 28-day concrete

Machine used: Gilson Compression Machine

Steps:

1. Take cylindrical samples out of mold

2. Put end caps on ends of cylinders

3. Put cylinder in compression machine

4. Slowly apply load until sample fails

5. Record maximum load

23
New cards

8.2 28-Day Splitting Test

Objective: Measures tensile strength of 28 day sample

Machine used: Gilson Compression Machine

Steps:

1. Place cylinder along length in loading platform

2. Place strip across cross-section so tension is along diameter

3. Slowly apply load until failure is reached

4. Record maximum load

24
New cards

9.1 Viscosity of Binders with the Rotational Viscometer

Objective: Determine viscosity of bitumen at various temperatures

Instrument used: Viscometer

Steps:

1. Set temperature on thermosel

2. Pour 8-10mL of bitumen into holder

3. Place holder into thermosel

4. Align thermosel and holder so they're above spindle hook

5. Attach spindle to hook and lower into holder

6. Wait for bitumen temperature to stabilize

7. Start spindle rotation at 20rpm

8. Record 3 readings 60 seconds apart at each test temp.

25
New cards

9.2 Shear Modulus and Phase Angle of Binders

Objective: Measures dynamic shear properties

Machine used: Dynamic Shear Rheometer

Steps:

1. Put specimen in DSR

2. Move test plates to squeeze bitumen.

3. Trim excess bitumen

4. Bring specimen to test temp and start test when temp is maintained for 10mins

5. Apply shear strain fro 10 cycles at 10rad/s

6. Program calculates complex shear modulus and phase angle

26
New cards

9.3 Low Temperature Stiffness with Bending Beam Rheometer

Objective: Determine lower grade of bitumen

Machine used: Bending Beam Rheometer

Steps:

1. Turn on cooling unit and calibrate machine

2. Make beam mold, 6.25x12.5x127mm

3. Pour bitumen into mold and let cool for 45mins

4. Trim and remove mold, place in cold bath for about 60mins

5. Place specimen in supports of BBR

6. Run automatic testing system

7. Print results

27
New cards

10.1 Superpave Gyratory Compaction

Objective: Compact sample to specific height or fixed number of gyrations

Machine used: Superpace Gyratory Compactor

Steps:

1. Heat mix and mold in oven

2. put filter at bottom of mold.

3. scoop mix into funnel and put into mold

4. place filter paper on top

5. place mold in compactor

6. Set compaction to 115 gyrations

7. Take out mold from machine

8. Let cool before handling

28
New cards

11.1 Theoretical Maximum Specific Gravity or Density of HMA (hot mix asphalt)

Objective: Determine specific gravity of mixed asphalt at room temp

Instrument used: Vibrating Table

Steps:

1. Warm sample and break up clumps

2. Weigh container

3. Add mix to container and weigh (container + mix)

4. Add water to container to cover mix and clamp shut with lid

5. Place container on vibrating table and turn on vacuum pump to pull air out of container. Leave this for 15mins

6. Stop pump and slowly release pressure

7. Place container in water, hook handle and measure contents (zero scale before hooking)

8. Remove mix from container and measure empty container

29
New cards

11.2 Bulk Specific Gravity of Compacted Bituminous Mixtures Using SSD Specimens

Objective: Determine Specific Gravity of compacted asphalt sample

Steps:

1. Measure dry mass of compacted specimen

2. Place specimen in water for 10mins

3. Tare scale with basket on hook

4. Place specimen in basket and record mass

5. Dry specimen with towel to get Saturated surface dry condition weight

6. Measure SSD weight