1/79
Looks like no tags are added yet.
What is the reason for hardness testing?
to measure a metal's resistance to indentation
What are the three methods of hardness testing?
Rockwell, Brinell, and Vickers
What is the minor load for the regular scale?
10 kg
What is the minor load for the superficial scale?
3 kg
What are the major loads for regular scale Rockwell?
60 kg, 100 kg, and 150kg
What are the major loads for superficial scale Rockwell?
15 kg, 30 kg, and 45 kg
What are the two types of indentors?
diamond cone (brale) or hardened steel ball
What is the notation for Rockwell A?
HRA
When is the minor load applied in hardness testing?
while zeroing the scale
What composes an HRA reading?
diamond indentor, 60 kg major load
What composes an HRC reading?
150 kg major load, diamond indentor
What Rockwell scales use the superficial scale?
N and T
What are the steps to tensile testing?
1. place machined specimen in tensile tester
2. apply tensile load, increasing until sample breaks
3. during loading, at intervals measure tensile load and length
4. after the sample breaks, but the broken ends together and measure length
How is stress calculated?
force/area
How is strain calculated?
(final length-original length)/ original length
What is the modulus of elasticity?
stress/strain in the straight line portion of graph; can't calculate when the graph isn't straight
What is percent elongation?
final strain *100%
What is the proportional limit?
when the behavior is elastic but not proportional
What is the yield strength?
when the material begins plastic deformation
What is the tensile strength or UTS of a material?
the highest strength achievable
What is the breaking strength?
the strength when the material breaks
What is ductility?
stretch, related to percent elongation
Modulus of elasticity measures what?
stiffness of a material
How do you find the 0.2% offset?
go to 0.2 on the strain axis (X) and draw a line that's parallel to the modulus of elasticity
What was the type of impact test used?
Charpy V notch
What was the impact testing machine set to before each test?
maximum value
What is the value that is shown after a specimen is broken during an impact test?
the absorbed energy in ft.lbs
What was the basic concept behind the impact testing lab?
to test the impact strength of samples at different temperature and plot them on a graph
When plotting the graph for ductile to brittle transition temperature, what should the axis' be labeled?
temperature on x, impact strength on y
What is ductile to brittle transition temperature?
the temperature at which the fracture energy passes below a predetermined value
What type of materials have ductile to brittle transition temperatures?
BCC materials
A 36
ferrite and pearlite
Gray Cast Iron (GCI)
ferrite, pearlite and graphite flakes
1095 Water Quenched and Tempered
martensite, ferrite and cementite
4340 A
ferrite and pearlite
Ductile Cast Iron
ferrite, pearlite and graphite spheroids
4340 WQ
martensite
Pig Iron
pearlite, cementite, and graphite flakes
Malleable Cast Iron (MCI)
ferrite and graphite nodules
1095 AC
pearlite and cementite
White Cast Iron (WCI)
pearlite and cementite
1095 WQ
martensite and cementite
Speroidized MArtensite
cementite spheroids and ferrite
Wrought Iron
ferrite and iron silicate stringers
Pack Carburized Steel
two outer layers-martensite and cementite
two inner layers-ferrite and pearlite
What is the echant composed of?
95% alcohol and 5% nitric acid
What is important to remember when mixing the echant?
always add the acid
What is the polishing media for metallography?
alumina or aluminum oxide
What are the sizes that the polishing media come in?
1, 0.3, and 0.05 michron
What are the order of the grit stages on the sandpaper used for etching?
240, 320, 400, and 600
What were the steels that were used during heat treating?
1018, 4340, and 52100
What were the three quench methods that were used in heat treating?
water, air, oil
What cooling method results in the hardest material?
water quench
What cooling method results in the least hard material?
air quench
How do tempering temperatures affect the material's hardness?
increases ductility, decreases tensile strength, increases impact strength and decreases hardness
Heating and cooling cycle for hardening
1650-1700 degrees F for 1hr/in of thickness; quench
Heating and Cooling cycle for tempering
800-1000 degrees F for 2 hours; air cool
Heating and Cooling cycle for annealing
1650-1700 degrees F for 1 hr/in of thickness; furnace cool
How was the lead-tin solidification diagram plotted?
x-axis was time, y-axis was temperature in degrees C
What is undercooling?
where the liquidus line dips down into the solid region
How is pack carburizing done?
a sample of low carbon steel is placed in a carbon rich material, activated charcoal, and is heated, so that the carbon diffuses into the steel
What are the temperatures and time for pack carburizing?
1650 degrees F for 8 hours
What is the grain size after pack carburizing?
large, and it must be refined
What is the two step heat treating process to refine grains?
first, you heat to 1650 for 30 minutes for small grains in the core and then to 1400 for 20 minutes for small grains in the case
What kind of stainless steel was tested during the cold working lab?
Austenitic stainless steel
What is the crystal structure of austenitic stainless steel?
FCC
As thickness of austenitic stainless steel was reduced, what happened to the hardness and magnetism?
they both increased
What effect did the two cooling rates have on the hardness after heat treating?
they both did not increase hardness since there is not a phase change to allow martensite to form
What happened to the hardness and magnetism after heat treating?****
they were lowered because of the recrystallization that occured
What should you do to the metal sample while grinding them in the metallography lab?
rotate it 90 degrees so that the replacement of scratches can easily be seen
What are the settings to the mounting press used for metallography?
use 1.25" mold with 4200 psi
What media was put into the mold for the metallography lab?
Phenolic or bakelite powder
DBTT
Ductile to brittle transition temperature
What should you do after you've finished grinding a metal sample with all 4 sand papers?
don't touch it with your fingers
Why is jominy testing used?
to determine the effect of alloying elements on microstructure development at different cooling rates
What were the major alloying elements in the samples used in jominy testing?
Chromium, Molybdenum, and Nickel
What were the three materials tested in jominy testing?
1045, 4140, 4340
How were the plots graphed for jominy testing?
distance from quenched end vs. HRA
Which sample from jominy testing had the highest hardenability?
4340
What is the most widely used hardness test?
Rockwell