Lightning Protection Systems (LPS)

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/20

flashcard set

Earn XP

Description and Tags

Vocabulary terms and standard definitions covering components, installation rules, testing, and standards for Lightning Protection Systems per I.S. EN 62305.

21 Terms

1
New cards

Lightning Protection System (LPS)

A complete system designed with two primary jobs: to intercept a lightning strike and safely conduct it to earth, consisting of internal and external protection working together.

2
New cards

Air Termination Network

The “strike point” component of an LPS that intercepts lightning before it hits the building; composed of air rods/finials, stretched wires, or a mesh of conductors positioned on high points, edges, and corners.

3
New cards

Roof Conductor

Conductors (usually bare copper or aluminium tape) that link air terminations together and initiate the path to ground, forming a mesh on flat roofs with grid dimensions dictated by the Lightning Protection Level (LPL).

4
New cards

Down Conductor

A conductor that provides a low-impedance vertical path from the roof to earth, installed as straight and direct as possible without sharp bends >90∘> 90^\circ (bend radius ≥20 cm\ge 20\,\text{cm}).

5
New cards

Bonding Conductor

A conductor with a minimum cross-section of 16 mm216\,\text{mm}^2 copper (or equivalent) used to equalize potential between metalwork, pipes, steel frames, and services to prevent side-flashing and hazardous voltage differences.

6
New cards

Test Point / Test Joint

A clearly labeled bolted clamp located in a test housing on each down conductor, typically 1 m1\,\text{m}–1.5 m1.5\,\text{m} above ground, enabling disconnection to test earth resistance.

7
New cards

Earth Termination Network

The combination of all earth electrodes connected in a ring around the building designed to disperse lightning energy into the ground.

8
New cards

Earth Electrodes

Conductive elements that provide the final connection to the “general mass of earth”, selected based on soil resistivity and available space (types include rod, plate, and lattice/mesh).

9
New cards

I.S. EN 62305 Series

The key publication and technical standard governing the design, risk assessment, installation, and testing of lightning protection systems in Ireland and the EU.

10
New cards

Rolling Sphere Method

A method defined in I.S. EN 62305 used to calculate and define the protected volume or “cone of protection” created by vertical air rods.

11
New cards

Mesh Method

A horizontal protection method applied on roofs where conductors form a grid varying in size from 5×5 m5 \times 5\,\text{m} for LPL I up to 20×20 m20 \times 20\,\text{m} for LPL IV.

12
New cards

Rod Electrode

The most common earth electrode type, consisting of 2.4 m+2.4\,\text{m}+ copper-bonded steel rods driven vertically into the ground, spaced at least one rod length apart when multiple are installed.

13
New cards

Plate Electrode

An earth electrode consisting of a 600×600×3 mm600 \times 600 \times 3\,\text{mm} copper plate buried at least ≥600 mm\ge 600\,\text{mm} deep, used where rocky terrain prevents the driving of vertical rods.

14
New cards

Lattice Electrode

An earth electrode made of a copper tape mesh buried directly in a building's foundation, particularly suited for new builds.

15
New cards

Bimetallic Connector

An approved connector required when joining dissimilar metals in an LPS installation to prevent galvanic corrosion.

16
New cards

Target Earth Resistance

The overall target electrical resistance for the entire connected lightning protection earth network, which must be <10 Ω< 10\,\Omega.

17
New cards

Joint Continuity Test Threshold

The maximum acceptable electrical resistance across conductor joints during an LPS continuity test, which is <0.2 Ω< 0.2\,\Omega.

18
New cards

How does Lightning develop and make its power

  • Development: Charge separation in thunderclouds → negative base induces positive charge on ground → stepped leader meets upward streamer → return stroke.

  • Voltage & Current: Can exceed 100 million volts. Peak currents 30kA typical, up to 200kA+. Rise time ∼1–10 microseconds.

  • Effects:

    • Thermal: Conductors can reach 30,000°C – causes fire, metal melting.

    • Mechanical: Shock waves from rapid air expansion crack concrete, dislodge roof tiles.

    • Electrical: Induced surges destroy electronics even without direct strike.

    • On People: Direct strike, side flash, step voltage, touch voltage – can be fatal.


19
New cards

Where is lightning most likely to strike

  • Tall or isolated structures

  • On hilltops or open ground

  • Have large roof areas

  • Contain flammable/explosive materials

  • House critical services: hospitals, data centers

  • High occupancy: schools, stadiums


20
New cards

what Factors should you check to determine a suitable design for lightning protection

  1. Lightning Protection Level needed – from risk assessment in EN 62305-2

  2. Building height, shape, roof type

  3. Construction materials – steel frame can be used as natural down conductor

  4. Soil resistivity – affects earth electrode choice

  5. Aesthetic requirements – concealed vs surface systems

  6. Existing services – coordination with antennas, solar PV, metal cladding


21
New cards

Installation Requirements & Precautions assoicated with Down Conductors: