Instrument Transformers, CTs, and Tariffs

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/24

flashcard set

Earn XP

Description and Tags

Comprehensive vocabulary flashcards covering current and voltage instrument transformers, CT construction types, safety protocols, accuracy classes, burden calculations, and industrial electricity tariffs.

25 Terms

1
New cards

Advantages of Instrument Transformers

Three primary operational benefits: enables the use of standardised measuring instruments, provides increased personnel and equipment safety by allowing the secondary circuit to connect to earth, and permits measuring instruments to be changed or serviced without isolating the electrical supply by using short-circuiting switches and voltage links.

2
New cards

Current Transformer (CT)

An instrument transformer (often referred to as a "series transformer") designed to step down high primary alternating currents to standardized, manageable secondary currents (typically 1 A1\,A or 5 A5\,A) proportional to the measured primary current.

3
New cards
<p>Voltage Transformer (VT)</p>

Voltage Transformer (VT)

A parallel-connected instrument transformer (also known as a potential transformer or PT) designed to present a negligible load to the supply, stepping down high system voltages (such as 400 V400\,V or 11 kV11\,kV) to safe, standardized levels (typically 110 V110\,V or 120 V120\,V) with an accurate voltage ratio and phase relationship.

4
New cards

CT Multiplier

The numerical factor obtained by dividing the primary current rating by the secondary current rating (e.g., 10005=200\frac{1000}{5} = 200); this factor is multiplied by the secondary ammeter reading to determine the actual line current flowing in the primary circuit.

5
New cards
<p>Secondary Burden</p>

Secondary Burden

The total impedance (resistance and reactance) connected across the secondary terminals of an instrument transformer, including the connected meters, protection relays, and circuit wiring, expressed in ohms (Ω\Omega) or volt-amperes (VAVA).

6
New cards
<p>Open-Circuit CT Secondary Danger</p>

Open-Circuit CT Secondary Danger

The hazardous condition when an energized CT's secondary circuit is opened; because the primary current acts as a constant current source without opposing secondary demagnetizing flux, the core drives into extreme saturation, producing dangerously high peak voltages (kVkV spikes) that cause dielectric insulation breakdown and severe shock hazards.

7
New cards

Toroidal Current Transformer

A current transformer constructed with a ring-shaped laminated core without an internal primary winding, designed so that the primary network conductor or cable passes directly through the central window to act as a single turn.

8
New cards

Wound-Type Current Transformer

A current transformer that includes distinct built-in primary and secondary wire-wound coils on the core, with the primary coil physically connected in series with the monitored circuit conductor; primarily used for lower current applications.

9
New cards

Bar-Type Current Transformer

A current transformer that uses an integral, fully insulated solid copper or aluminium bar or busbar as its single-turn primary conductor, permanently mounted and bolted into switchgear assemblies.

10
New cards

Split-Core Current Transformer

A type of current transformer featuring a separable or hinged magnetic core that can be opened, fitted around an existing busbar or cable, and closed without requiring the primary conductor to be disconnected.

11
New cards

Primary Turns Ratio Modification

The technique of altering the effective transformation ratio of a window-type CT by wrapping the primary conductor through the core window for multiple passes (e.g., passing a cable twice through a 300/5 A300/5\,A CT converts it into a 150/5 A150/5\,A unit).

12
New cards

Measurement Accuracy Class

A CT accuracy designation (such as Class 0.2 or Class 0.5) designed for energy billing and revenue metering that guarantees high precision and minimal ratio/phase error within standard operating load levels.

13
New cards

Protection Accuracy Class

A CT accuracy designation (such as Class 5P or Class 10P) intended for protective relays; it maintains linear performance and avoids magnetic saturation during extreme overcurrents and system faults to guarantee reliable tripping.

14
New cards

Metering CT Selection Rule of Thumb

The engineering design guideline dictating that a metering CT should be selected with a primary current rating slightly higher than the maximum expected continuous load current to avoid magnetic core saturation and maximize measurement accuracy.

15
New cards

Watthour (W/h) Multiplier

The overall multiplying factor applied to a watthour meter reading to determine actual energy consumption in installations utilizing both CTs and VTs, calculated as: W/h Multiplier=CT Multiplier×PT Multiplier\text{W/h Multiplier} = \text{CT Multiplier} \times \text{PT Multiplier}.

16
New cards

Maximum Demand (MD)

The highest rate of electrical energy consumption, recorded in kilowatts (kWkW) or kilovolt-amperes (kVAkVA), drawn by an installation during any predefined integrating period (typically 15 or 30 minutes).

17
New cards

Load Factor

The ratio of the average electrical load consumed over a specific time duration to the maximum demand observed during that same duration (Load Factor=Average LoadMaximum Demand\text{Load Factor} = \frac{\text{Average Load}}{\text{Maximum Demand}}), reflecting consistency of electrical use.

18
New cards

Diversity Factor

The ratio of the sum of the individual maximum demands of separate consumer subdivisions to the coincident maximum demand of the entire group (Diversity Factor=∑Individual MDGroup MD\text{Diversity Factor} = \frac{\sum \text{Individual MD}}{\text{Group MD}}), which is always greater than 1 (>1> 1).

19
New cards

ESB Low Voltage Maximum Demand Bill Components

The component charges listed on an ESB industrial electricity bill: Standing Charge, P.S.O Levy, Service Capacity Charge, Demand charge, Day Units, Night Units, and Low Power Factor Surcharge (applied to kVArhkVArh exceeding one-third of total kWhkWh).

20
New cards

ESB Networks Power Factor Interface Code

The grid interface regulation requiring industrial and commercial customers to maintain a power factor of at least 0.950.95 lagging to prevent reactive charges; installations with a power factor below 0.850.85 may be refused grid connection.

21
New cards

Capacitor kVAR Sizing Formula

The mathematical equation used to determine the capacitor rating needed to improve an installation's power factor: Qc=P×[tan⁡(ϕ1)−tan⁡(ϕ2)]Q_c = P \times [\tan(\phi_1) - \tan(\phi_2)], where PP is the active power in kWkW and ϕ=arccos⁡(power factor)\phi = \arccos(\text{power factor}).

22
New cards

Instrument Transformer Terminal Markings

The standard polarity designations where CT primary terminals are labeled P1 and P2 (P1 oriented toward the supply) and secondary terminals are labeled S1 and S2 (S1 toward the instrument); VT primary terminals are labeled A and N, with secondaries labeled a and n.

23
New cards

Smart Meter

An advanced electronic electricity meter integrating a microprocessor, analog-to-digital converter, and two-way communication module (via Power Line Communication, RF mesh, or 4G) to record and transmit interval consumption data every 30 minutes.

24
New cards

Clamp Meter

A portable, handheld testing device incorporating an integral split transformer core that clamps around an active conductor to measure alternating current safely via magnetic induction without interrupting the circuit.

25
New cards

CT Installation Procedure

The strict 4-step sequence required when putting a current transformer into service: 1) Short-circuit secondary terminals, 2) Pass the primary conductor through the core, 3) Connect secondary wiring securely to the meter, and 4) Remove the secondary shorting link before energising.