1/79
Looks like no tags are added yet.
line-to-neutral
the voltage measured between a hot and the neutral
line-to-line
the voltage measured between hot to hot
single phase voltage
120/240
what is another name for single phase
two phase or split phase
how does single phase work
there are 2 hot wires that push in opposite directions (120V each x 2 = 240V), which is split by the neutral
single phase - contains
1 or 2 hots, 1 neutral, 1 ground
single phase 1 pole - voltage
120v (1 hot)
single phase 2 pole - voltage
240v (2 hot)
single phase main/service - voltage
120/240V (2 hot)
single phase - line to neutral
120v
single phase - line to line
240v
power formula
P = E x I or P = V x A
three phase voltage
low = 208/120v
high = 480/277v
three phase - contains
3 hots, 1 neutral, 1 ground
three phase low - voltage
120/208V
three phase low - typ. locations
big offices, outlets, residential
three phase high - voltage
480/277V
three phase high - typ. locations
used for big equipment and commerical lighting
how much does each hot have in three phase high
277 V each
power formula for 3-phase
P = E x I x 1.732
switch board
a panel that divides incoming power feed into smaller branch circuits
switch board - purpose
safely distribute electricity
switch board - typ. locations
heavy-duty commercial, industrial plants, data centers
switch boards - loads
high loads ~ 1200A-6000A
panel boards
an electrical panel that takes incoming power supply and divides it into branches
panel boards - loads
up to 1200a
main circuit breaker (mcb)
the electrical panel has its own main breaker which then supplies power to panel busbars
why would a mcb be preferred
used when the panel acts as the main service entrance
mcb - pros & cons
pros - provides total local circuit control and instant internal shutoff
cons - costs 30-100% more than a mlo
main lug only (mlo)
a panel with no main breaker, only lugs for incoming wires; relies on breaker upstream for protection
mlo - components
feeder wires land on lugs that are connected directly to the panelboard bus
mlo - pros & cons
pros - cost saving, less space, easy multi-panel expansion
cons - no local shutoff, code limits, and requires upstream protection
mlo - preference
when power is already supplied from an upstream device, which already provides overcurrent protection and disconnection
breakers
a safety switch in the panel that automatically shuts off a circuit when too much current (amps) flows thru it
breaker rating
the # of amps at which the breaker trips/shuts off
1-pole breakers
connects to 1 hot wire to supply 120v
1-pole breakers - typ. uses
standard residential and light commerical ; general lighting, room outlets, and small appliances
2 pole breakers
connects to 2 hot wires (of opposite phases) to supply 240v
2 pole breakers - typ. uses
large household, commerical appliances, dryer, central ac, water heaters
3-pole breakers
connects to 3 hot wires to interrupt 3-phase power
3 pole breakers - typ. uses
industrial, heavy commercial, motors, industrial pumps, machinery, and hvac
tandem breakers
a single-pole circuit breaker that fits into a single slot, but supplies power to 2 seperate 120v circuits
what happens if one circuit overloads in a tandem breaker?
the other one stays on
branch circuits
the small wires that carry power out of the panel to the loads (lights, outlets)
feeder
the large wires thar bring power into a panel from upstream (such as a xmfr or distribution panel)
encapsulated xmfr (indoor xmfr)
dry-type electrical transformer where the core and coils are sealed in epoxy resin
encapsulated xmfr - rating
typ under 75 kva
encapsulated xmfr - con
CANNOT be repaired, only replaced
flexible metal conduits (fmc)
a metallic tube of interlocked metal strips that is bendable by hand
fmc - preferrence
where movement or vibration is present, or where it may be difficult to bend
used in short final connections
fmc - connections
screw in, set screw, threaded couplings
metal clad (type mc) cable
a cable that consists of 2+ individually insulated wires and a separate grounding wire inside a flexible metal outer jacket
mc cable - materials
solid or stranded copper, aluminum
mc cable - simple def
insulated wires come pre-installed inside the metal
mc cable - preference
meant for long runs or commercial work
mc cable - typ. locations
commercial building walls & ceilings
mc cable - connections
snap in or set screws
romex
non-metallic sheathed electrical cable which contains insulated wires wrapped in a plastic jacket
romex - preference
residential construction, low cost, and fast installation
romex - typ. locations
exposed or concealed spaces in dry residential locations
romex - connections
built in cable clamps or snap-ins
nec - 3 ft rule
there needs to be a minimum of 3’ clear space in front of electrical equipment so someone can work on it safely
nec - dedicated space rule
the space above / below electrical equipment is reserved ONLY for electrical
nec - 6’-7” rule
the center of the highest breaker or switch handle cannot be more than 6’-7” above the floor
nec - 6 handle rule
you must be able to shut off the power to a building with 6 or less hand motions at one location
what happens if there are more than 6 hand motions for the nec - 6 handle rule
a main breaker is required
electrical energy consumption formula
e = p x t
cost formula
$ = e x r
grounding
connecting the electrical system to the earth so stray or fault has a safe path into the ground
grounding - purpose
protects people from shock if a wire touches metal
helps a breaker trip quickly during a fault
gives lightning and power surges a safe exit into the earth
grounding conductor
the wire that connects the electrical system to the ground rod, which links it to the earth
ground rod
a metal rod driven into the earth that connects the electrical system to the ground
how far apart must 2 ground rods be from each other
6 ft
grounding path
a permanent, low resistance electrical connection designed to safely carry fault currents back to their source
grounding path - purpose
protect people and allow circuit breakers to trip quickly
grounding path - simple def
the path of least resistance
hot-to-ground fault
occurs when a hot wire makes unintended contact with a ground wire, ground metal surface, or path to earth
hot-to-ground fault - how?
a current will divert along the grounding path which creates an immediate shock hazard or tripping a breaker
hot-to-ground fault - causes
loose or damaged wires
worn insulation
water getting inside equipment
hot-to-ground fault - key idea
electricity always tries to get back to its source and it takes the easiest path