1/119
Looks like no tags are added yet.
LAB 1 INTRO LAB EXCERCISE
-Study Error
-Precision
-SIG FIGS
-Construction of Graphs
-How to use air track measurement system for motion exercises
...
LAB 1: error & accuracy & %error & diff
-Error: diff between value of physical quantity determined by experiment and true value
-Types of error may occur during an experiment: experimentalist not take the time to be as accurate & detailed
-Accuracy: percentage diff or absolute diff
-Percentage Error = (Estimated- Actual)/ (Actual) x 100
Percent difference= | E1- E2 | / 1/2(E1 + E2) x 100
LAB 1- precision
-related to way u carried out measurements & how u reported ur results
-precision of a number indicated by # of sig figs used
LAB 1: Sig Figs
leftmost nonzero # = most sig
rightmost nonzero # = least sig
LAB 1: true regarding significant figures
-most significant digit is always the leftmost nonzero digit, regardless of where the decimal point is found.
-least significant figure is the rightmost nonzero digit if there is no decimal point or the rightmost digit, whether zero or not, if there is a decimal point.
-All digits between the least and most significant digits are counted as significant figures.
LAB 1: The result of a multiplication or division should have how many significant figures?
As many as the factor with the least amount of figures
LAB 1:
When excess digits are dropped from a number, the last digit retained should be
ROUNDED
LAB 1: GRAPH PART:
-(the measured/dependent variable on y-axis and (set or independent variable on x axis
-prediction is correct=results should be straight line w slope C
equation for straight line: y =(slope)x + (intercept)
LAB 1: graph continued
-best line of fit: line that agrees w/ trend of the plotted data points while minimizing error
-slope is evaluated: drawing right triangleABC & THEN DETERMINE LENGTH OF THE SIDES AB AND BC-slope is ratio of bc to ab
LAB 1: apparatus
apparatus: studies straight line motion
LAB 1: The Air Track
-no friction & air track level=air track not move
-not leveled=gilder will move back n forth and it could be adjusted by the bolt on the bottom
-ours wasn't so we adjusted bolt and made it lower so the glider would remain in place
LAB 1: air track
when track is lvl, push glider and watch motion
-overtime glider does slow down & eventually stops. (friction reduced but NEVER ZERO)
LAB 1: air track continued
sources of friction slowing glider down
-air resistance
-friction from hitting bumpers
lab 1: air track continued
what can you to cause the glider to accelerate even after you let go (ignore friction)
adding more air once the glider is in motion and tilting air track
lab 1: air track continued
what can the yellow ruler stip on air track be used to measure?
measures distance between two successive placements on the glider
lab 1: air track continued
what do ur results say ab the accuracy of motion detector?
-affects time & position based on where it started
-started glider at 0.4 m on roller & moved it to 0.7 m on the ruler while measuring it on computer
-computer read 0.298 m
lab 1: air track continued
percent error
(measurement - ideal) / ideal
lab 1: air track continued
orientation of motion detector
oriented up=detect motion stop the metal plate which skews data & if oriented down, motion might affect data bc of glider
LAB 2: Motion with constant acceleration
-measure access of object that slides down an inclined plane and deduce the accel due to gravity from ur data
-real purpose of lab: relationships between position, velocity, access, and time
...
LAB 2:
primary objective for this lab
measure the accel of an object moving in a straight line
LAB 2:
(equation) if initial coordinate of the object is x0 then later time (t)
x=x0 + v0t + 1/2at^2
Lab 2:
(equation) where v0 is initial velocity of object, the velocity id the object at any time:
v=v0 + at
LAB 2:
third useful equation
v^2 = v0^2 + 2a(x-x0)
LAB 2:
body moving down a frictionless plane inclined at an angle θ, HAS A THEORETICAL ACCEL: (equation)
a = gsintheta
g: accel due to gravity
theta: angle inclined plane makes w horizontal
LAB 2: forces acting on glider? free body diagram
weight (mg)
normal force (N)
mg resolved into parallel and perpendicular
x and y (newton's law)
LAB 2:
-Place 2 spacer under one end of air creating an incline
-measure height of spacers to calc angle of incline
-use trig w the spacer height and track length to find the incline plane
-prepare computer system to record motion of glider
-release glider from rest on the inclined and let it slide down
-gather data on glider's motion
...
LAB 2:
Q1: what does a straight line segment in graph of position vs time mean?
constant velocity
LAB 2:
Q2: What does a curved line mean
-velocity is not constant
-if its curved, velocity is increasing
LAB 2:
Q3: What is the pattern when a glider strikes and rebounds from the end of the track?
find angle of incline: F=ma=mgsin(theta)
velocity is inc until it strikes ^ rebounds then, the velocity & position are negative
LAB 2:
Q4: Meanings of A, B, and C
y=C + Bt + At^2
A=1/2 of the accel (m/s^2)
B= Initial velocity (m/s)
C= initial postion (m)
LAB 2:
Q4: are the numbers obtained for B and C reasonable? explain
yes bc they should both be close to zero
LAB 2:
Q5: deduce G
sin(theta) = h/L
a=gsin (theta)
L= sqrt(h^2 + base^2)
g= a/(sin(theta))
LAB 2:
when plotting the object's position as a function of time, you notice the graph is linear. What does this tell you about the object's velocity?
constant
LAB 2:
When plotting an object's position as a function of time, you notice the graph is linear. What does this tell you about the object's acceleration?
it is zero
LAB 3: EQUILIRIBRIM OF A POINT MASS
static equilibrium of object with mass under concurrent forces
LAB 3:
What are the two conditions met when a body is in equilibrium?
1) the vector sum of all forces acting on the object must be zero
2) the sum of all the torques acting on the object must be zero
LAB 3:
What is a concurrent force?
if the lines of action of the forces intersect at a point
LAB 3:
Vector addition
graphical and analytical
LAB 3:
Vector addition: graphical
LAB 3:
When drawing vectors, the length of the arrow should be proportional to the magnitude of the vector.
TRUE
LAB 3:
When adding two vectors graphically, one vector is drawn such that its tail lies at the ____ of the other vector. (Hint: A common name for the graphical method is the "_____ to tail method".)
TIP
LAB 3:
Say you've set out to graphically add two force vectors, →F1 →F2 with magnitudes 3N and 6N. if the arrow representing
→F1 is 5 cm long, how long should you draw the arrow representing →F2
given F1 has magnitude of 3N and represented 5 cm
5cm/3 N= 1.67
Length of F2 = F2's magnitude x arrow representing f1/f1's magnitude
6N x 1.67 = 10
LAB 3:
When adding vectors analytically, one starts by calculating the x and y components of the individual vectors. Adding all of the x components together yields the ________ of the resultant vector.
X COMPONET
LAB 3:
When adding vectors analytically, one starts by calculating the x and y components of the individual vectors. Adding all of the y components together yields the ________ of the resultant vector.
Y COMPENET
LAB3 ;
Once the x and y components of a resultant vector are found analytically, the magnitude of the resultant can be determined by using the Pythagorean theorem.
TRUE
LAB 3:
Once the x and y components of a resultant vector are found analytically, the direction of the resultant can be determined by using the arctangent function.
TRUE
LAB 3:
Which of the following vectors are the resultant of adding vectors A and B?
A= 2.7N @ 48 deg, B=4.N @ 201 deg
vector a:
x-component: 2.7cos(48)
y-component: 2.7sin(48)
vector b:
x-component: 4.1cos(201)
y-component: 4.1sin(201)
add a's x component + b's x component
add a's y + b's y
sqrt(sum of a and b's x component)^2 + sum of a and b's y component^
answer for ^ that = magnitude
answer for degrees part
(sum of a and b's y component / sum of a and b's x-component)
LAB 4: Newton's second law
measure mass in motion on a level air track
F=MA
LAB 4:
measuring acc but not tension of masses depicted and the tension in the string connecting them (equation)
a= m2/ m1 + m2
LAB 4:
Procedure
-Level air track
-Perform initial motion measurements using a 10-gram mass on glider. -Practice moving glider, then collect data w/a motion detector & computer while allowing glider to move from maximum stretch of string to its first bounce. -Analyze data w/curve-fitting tool to determine glider's acceleration & print the graph w/fit.
-Repeat process to gather new data
-Calc accel as per Newton's Second Law, compare w/measured values, calculate percent error, and note the causes of any error in the space labeled Q1.
STREP 3: Perform a second set of measurements to account for friction effects, starting the data recording just before the glider hits the bumper at the end of the track and rebounds.
LAB 4:
Accounting for friction between the glider and the track requires us to distinguish between two cases: one being when the glider is moving away from the motion sensor, and the other being when the glider is moving towards the motion sensor.
TRUE
LAB 4:
Q1
CALC ACCELERATION
(you are asked to calc accel and percent error)
m2g x g/ m1+m2
LAB 4:
CAUSES OF ERROR
friction and human error
LAB 4:
Q2
glider movie toward motion detector accel
a= (f + m2g)/(m1+m2)
LAB 4:
Q3: avg accl meaurements
a=1/2(a'+a'') = m2g/m1+m2
a' means case 1
a'' means case 2
LAB 4
Q4:
Is a level track necessary for accurate measurements in procedure 4
yes and no
yes bc lvl ensures that the only acc acting on glider is due to forces specifically apply for exp
not necessary bc we are calc avg accel so even tho a' and a'' change, the avg doesn't
LAB 4:
why is a' - a'' most useful for friction force?
Shows magnitude of friction force
LAB 5:
Procedure: uniform circular motion
LAB 5:
Q1 does ur data support the prediction that radial force depends on the square of the rotation of speed
yes bc the plot of radial force vs v^2 results in a line, a positive linear correlation
LAB5:
Q2: What quantity is described by the slope of the fit to the F vs v^2 graph
mass over radius m/r is the slope
LAB 5:
Q3: Intercept of mass vs number graph
represents initial weight of the carriage prior to adding any mass
compared to other groups, our intercept is smaller, due to diff in radius & guessing the intercept
LAB5 :
Q4 force vs radius graph
fit coefficient is m/r so m/r vs r graph would have an inverse relationship
LAB5
Q5: What physical object provided the necessary radial force to keep the sliding carriage moving in a circle? what type of force was this?
the string -provides tension force- provided necessary radial force to keep the sliding carriage moving in a circle
LAB 5:
Q6 What other types of forces can be used as. radial force?
gravity
fiction
magnetic force
LAB 5:
Q7 describe one way this apparatus might be modified to use a diff type of force to make the sliding carriage move in a circle
apparatus can be modified to rate vertically where gravity would be force to keep the sliding carriage moving in circle
LAB 5:
An object is undergoing uniform circular motion. Which of the object's quantities remains constant?
SPEED
LAB 5:
For uniform circular motion specifically, an object's acceleration vector points _________ the circular path.
Towards the center of
LAB 5: Which of the following are names for the acceleration of an object undergoing uniform circular motion?
Radial and centripetal
LAB 5:
Two objects are undergoing uniform circular motion with the same speed and radius. Object 1 has mass m and is subject to a net radial force of magnitude F1 Object 2 has mass 2m and is subject to a net radial force of magnitude F2
Which statement can be made about the forces on these two objects?
F1=1/2F2
LAB 5
Two objects of the same mass are undergoing uniform circular motion with the same radius. Object 1 is moving at speed v and is subject to a net radial force of magnitude F1
Object 2 is moving at speed 2v and is subject to a net radial force of magnitude F2
Which statement can be made about the forces on these two objects?
F1=1/4F2
LAB 5: Two objects of the same mass are undergoing uniform circular motion with the same speed. Object 1 is moving at radius r and is subject to a net radial force of magnitude F1
Object 2 is moving at radius 2r and is subject to a net radial force of magnitude F2 Which statement can be made about the forces on these two objects?
F=2F
LAB 6:
PROCEDURE
LAB 6:
Two objects collide and stick together. The fact that both masses are stuck together makes this a ______________ collision.
completely inelastic
LAB 6:
The primary objective of this experiment is to use two different methods to calculate the _____________ of a projectile fired by a ballistic pendulum.
INTIAL VELOCITY
LAB 6:
Using a ballistic pendulum, you fire a ball of mass 15.0 g at stationary pendulum bob of mass 210.0 g and the masses stick together as they swing upward. You measure that the ball and pendulum bob swing 12.3 cm above their starting height. How fast were the objects moving right after the collision?
PE= (M1+M2) x g x h
KE= 1/2(M1+M2)V^2
set them equal to eachother to solve for v
(m1+m2) x g x h = 1/2(m1+m2)v^2
SIMPLIFIED ...
2 X (M1+M2) X G X H= (M1 +M2)
2 X g x h = v^2
v = sqrt 2 x g xh
LAB 6:
Using a ballistic pendulum, you fire a ball of mass 15.0 g at stationary pendulum bob of mass 210.0 g and the masses stick together as they swing upward. You calculate that both objects were moving together with speed V = 2.10 m/s right after the collision. How fast was the ball moving initially?
m1 x v1 = (m1 + m2) x V
m1=15 g
v1=?
m2=210.0 g
V=final velocity 2.10
v1=(m1 + m2)V/m1
LAB 6:
You fire a spring gun such that its height from the ground is 1.31 m and use it to fire a ball of mass 15 g horizontally. How long will it take for the ball to hit the ground?
t=sqrt 2y/g
y=vertical displacement (1.31)
LAB 6:
You fire a spring gun such that its height from the ground is 1.31 m and use it to fire a ball of mass 15 g horizontally. You measure the horizontal distance the ball traveled to be 4.05 m and calculate that the ball was in the air for 0.825 s. What was the initial velocity of the ball as it was launched by the spring gun?
Vo= d/t
LAB 6:
method more accurate
free flight method fit more accurate bc more realistic- not as much as friction
LAB 6:
What uncertainty is associated w the discrete number of teeth in the ratchet assembly of ballistic pendulum
when pendulum reach its highest height, its b/n2 of the teeth so it goes down to next one so there is uncertainty there & friction
LAB 6:
experiment ballistic pendulum
mass directly impacts how much KE there is - the KE for the 2nd one much smaller bc velocity smaller
LAB 8:
procedure
Lab 8:
elastic collision- what happened to the left hand glider after the collision? why?
-velocity changed direction
-magnitude of velocity decreased bc it lost momentum during collision
-not a true elastic collision bc KE not fully conserved
LAB 8:
unknown mass- exp, after the collision what happened to speed of the more massive glider
speed decreased
LAB 8:
after the collision, is speed of the less massive glider larger/smaller than the initial speed of the more massive glider
speed of the less massive is larger
LAB 8:
value of unknown mass
m1v1=m1vf+m2v2f
LAB 8:
What may have caused errors in the experimental determination of unknown mass
air track not being leveled
speed of letting go & force used
LAB 8:
Describe what u observe regarding speeds and directions of each glider before and after the collision
-when smaller mass hits larger mass = velocity inc more
-larger mass has a smaller velocity than smaller mass object
LAB 8:
n an inelastic collision, ___________ is conserved, but _________ is not.
Momentum
KE
LAB 8:
Which quantities are conserved in an elastic collision
KE and momentum
LAB 8:
An object of mass 150 kg is moving with a speed of 4.5 m/s. What is the magnitude of the object's momentum?
Momentum (p) = Mass x Velocity
LAB 8:
An object of mass 150 kg is moving with a speed of 4.5 m/s. What is the magnitude of the object's kinetic energy?
KE= 1/2 X Mass X Velocity^2
LAB 9: STATIC EQULIBRIUM
PROCEDURE
LAB 9:
center of mass?
-weight(mass) is equally distributed on both sides
LAB 9:
If we know the sum of the forces acting on an object is zero, then we can say for sure that the object is in equilibrium
true
LAB 9:
An object is subjected to a force F applied a distance r away from the axis of rotation at an angle of θ
r x sin(theta)
LAB 9:
Counterclockwise torques are considered positive by standard sign convention, while clockwise torques are negative.
true
LAB 9:
U apply a force on the end of a wrench of length r, while your arm and the wrench form an angle θ
If start using new wrench w/double length, what do you expect to happen to the amount of torque you generate?
INC BY 2
LAB 9:
While attempting to remove stubborn lug nut from wheel on your project car, you apply force on the end of a long wrench w/length 18.5 cm, such that your arm and the wrench form a 90 degree angle. The lug nut isn't budging, so you start to push harder until it finally comes loose when you push with 212 N of force. How much torque was required to loosen the lug nut?
TORQUE=FORCE X LENGTH (METERS)
m-->cm
multiply cm by 100
cm-->m
divide by 100
g-->kg
g divide 1000
LAB 9:
Now it's time to put a new set of wheels on your project car. The manual for the new wheels says that the lug nuts should be applied with at least 225 Nm of torque for safety purposes. You can only muster a pushing force of 250 N. If you push against the wrench at an angle of 90 degrees, what is the shortest wrench you would need to tighten the lug nuts to their specifications?
L=TORQUE/F