1/55
Comprehensive vocabulary flashcards covering electronic components, schematic symbols, laboratory tools, multimeters, and circuit testing principles.
Multimeter
A handheld measurement instrument capable of testing parameters such as AC and DC voltage, AC and DC current, electrical resistance, diode operation, continuity, frequency, capacitance, and temperature.
Continuity Testing
A multimeter test mode that emits an audible sound via a piezo buzzer and displays a three-digit resistance reading when a complete electrical path exists between the test probes.
Open Loop (OL)
A reading displayed on certain multimeters when the test probes are not touching or when there is an open circuit, indicating that no electrical continuity exists.
Resistance Testing
A measurement performed by applying a small test voltage to observe current flow; it must be conducted only when the component is completely unpowered and removed from the circuit.
Direct Current (DC) Voltage
A steady electrical potential produced by sources such as chemical reactions inside batteries, keeping the voltage substantially constant until the energy source depletes.
Alternating Current (AC) Voltage
An electrical potential that periodically reverses direction, such as mains electricity oscillating at 50Hz between approximately −240V and +240V.
Current Measurement
A measurement procedure that requires physically breaking the circuit and placing the multimeter in series so that all electrical current flows directly through the meter.
Dual Benchtop DC Power Supply
A laboratory power source providing two variable DC outputs (0−30V, 3A) and a fixed 5V (3A) supply, each with individual controls.
Constant Current (CC) Mode
An operating condition entered when a circuit attempts to draw more current than the threshold set by the current knob, causing the CC indicator LED on the power supply to illuminate.
Independent Mode
A power supply mode where the two variable output channels operate completely separately, allowing independent control of their respective voltages and current limits.
Series Mode
A power supply mode where both channels are linked internally in series to create a bipolar supply; channel 1 controls the voltage for both channels, and current limit is determined by the lower current knob setting.
Parallel Mode
A power supply mode where both channels are linked internally in parallel to supply larger currents, with voltage and current limit determined entirely by channel 1 controls.
Breadboard
A reusable, solderless construction base featuring interconnected internal socket holes, used for the rapid, temporary prototyping of electronic circuits.
Breadboard Power Bus Lines
The outer columns of a breadboard configured in long vertical conductive strips, typically dedicated to distributing positive power and ground across the board.
Breadboard Terminal Strips
The inner sections of a breadboard organized into short horizontal five-hole rows separated by a central divider, used for mounting and connecting individual electronic components.

Claw Hammer
A hand tool featuring a hardened metal striking head on one side and a curved claw on the other, used for driving and extracting nails.

Hacksaw
A fine-toothed hand saw held in a C-shaped frame under tension, used for cutting metal and rigid plastic materials.

Logic Probe
A handheld testing instrument equipped with indicators and audio tones to determine high, low, or pulsing logic levels in digital circuits.

Crocodile Cable
An electrical wire terminated at each end with spring-loaded, serrated metallic clips, used for creating temporary test connections.

Desoldering Pump (Suction Pump)
A handheld mechanical device that uses a spring-loaded vacuum piston to evacuate molten solder from a joint during component rework.

Vero Board (Stripboard)
A pre-punched prototyping circuit board with parallel copper tracks along one face, designed for soldering components into permanent or semi-permanent circuits.
Cell
A single electrical unit that provides electrical energy via internal chemical reactions, represented schematically with its longer line indicating the positive terminal.
Battery
An electrical energy source consisting strictly of two or more interconnected cells joined together.
Fuse
A safety protective component containing a sacrificial conductor designed to melt and open the circuit when the electric current exceeds a specific rating.

Transformer
A device composed of two wire coils linked magnetically by an iron core to step up or step down AC voltages without direct electrical contact between the coils.
Earth (Ground)
A zero-volt (0V) circuit reference point for power supplies, or a direct physical conductive connection to the earth in mains electricity and radio systems.
Inductor (Coil, Solenoid)
A coil of wire that establishes a magnetic field when current passes through it, functioning as an electrical filter or as a transducer converting electrical energy into pulling motion.
Push-to-Break Switch
A momentary switch that remains normally closed, interrupting the flow of electrical current only while its button is depressed.
SPST Switch
A Single Pole, Single Throw switch that toggles a single circuit path on or off, permitting current to flow only when in the closed position.
SPDT Switch
A Single Pole, Double Throw switch that directs current from a common terminal to one of two alternate paths, sometimes featuring an intermediate central off position.
DPST Switch
A Double Pole, Single Throw switch that controls two separate circuits simultaneously, commonly used in mains wiring to isolate both live and neutral lines.

DPDT Switch
A Double Pole, Double Throw switch containing two independent poles that each toggle between two throws, frequently wired to reverse electric motor direction.

Relay
An electrically operated switch containing an electromagnetic coil that actuates isolated switch contacts (Normally Open, Common, Normally Closed) to switch higher-power circuits.
Rheostat
A two-contact variable resistor used primarily to regulate electrical current, such as controlling lamp brightness, motor speed, or capacitor charging rates.
Potentiometer
A three-contact variable resistor functioning as an adjustable voltage divider, capable of translating spindle position or angle into an electrical voltage signal.
Preset Resistor
A compact, economical variable resistor adjusted using a screwdriver during circuit manufacturing and calibration, designed to remain untouched thereafter.
Polarized Capacitor
A large-value capacitor (≥1μF) designed with designated positive and negative leads that must be oriented correctly in a circuit to prevent component failure.
Un-polarized Capacitor
A small-value capacitor (≤1μF) with high voltage ratings (≥50V) that can be installed in either direction without polarity restrictions.
Capacitor Number Code
A three-digit code on small capacitors where the first two digits represent the value, the third digit indicates the number of following zeros, and the result is read in picofarads (pF).

Light Emitting Diode (LED)
A semiconductor transducer that converts electrical energy into light; its positive anode is the longer lead, and its negative cathode is the shorter lead aligned with a flat casing notch.
Zener Diode
A specialized diode engineered to allow reverse conduction at a specific reverse breakdown threshold, thereby maintaining a stable fixed reference voltage across its terminals.
Photodiode
A light-sensitive semiconductor diode designed to generate or modulate electrical current in response to incident light exposure.

Transistor NPN
A bipolar junction transistor utilized for signal amplification and switching, indicated in circuit diagrams by an emitter arrow pointing away from the base.

Transistor PNP
A bipolar junction transistor utilized for signal amplification and switching, denoted schematically by an emitter arrow pointing inward toward the base.
Galvanometer
An analog current-sensing meter of extreme sensitivity, designed to detect and measure tiny electric currents typically below 1mA.
Oscilloscope
An electronic laboratory test instrument used to graphically display the waveform shapes of electrical signals across time, measuring voltage amplitudes and time periods.

Light Dependent Resistor (LDR)
An input sensor transducer whose electrical resistance changes in response to incident light levels, decreasing in resistance as brightness increases.
Thermistor
A temperature-sensitive resistor that converts changes in ambient temperature (heat) into predictable changes in electrical resistance.

NOT Gate (Inverter)
A logic gate with a single input that produces an inverted output, outputting true (1) when the input is false (0) and false when the input is true.
AND Gate
A digital logic gate with two or more inputs whose output is true (1) only when all of its inputs are simultaneously true (1).
NAND Gate
A Not-AND logic gate whose output is true for any input combination except when all inputs are simultaneously true (1).
OR Gate
A digital logic gate with two or more inputs that produces a true (1) output whenever at least one input is true (1).
NOR Gate
A Not-OR logic gate that outputs true (1) only when none of its inputs are true (all inputs are low or false).
EX-OR Gate
An Exclusive-OR logic gate with two inputs that outputs true (1) only when its two inputs are in different logic states.
EX-NOR Gate
An Exclusive-NOR logic gate with two inputs that outputs true (1) only when both inputs share the exact same logic state.
Resistor Colour Code
A color-based numbering convention from 0 (Black) to 9 (White) used on axial resistors to mark numeric values, multiplier factors, and manufacturing tolerance percentages.