Programming & Analysis Flashcards

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/167

168 Terms

1
New cards

How is gross floor area measured for code purposes versus other purposes?

For code purposes, measure to the exterior face of the exterior walls. For other purposes—such as zoning, cost estimating, and commercial leasing—measure to the interior face of the exterior walls.

2
New cards

What is a catchment area in terms of water runoff?

The specific region of land where precipitation, snowmelt, and surface water gather and drain by gravity into a single common outlet, such as a river, lake, reservoir, wetland, stream, culvert, catch basin, or storm drainage system.

3
New cards

Where is an outdoor noise barrier most effective relative to the noise source and receiver?

Place it as close as practical to either the noise source or the receiver. A barrier near the midpoint between them is generally less effective.

4
New cards

What does a population pyramid illustrate?

A graph showing the age and sex distribution of a population, typically with age groups arranged vertically and population counts or percentages shown on opposite sides.

5
New cards

With windows open, how does wind create positive- and negative-pressure zones around a building?

Windward surfaces and spaces directly exposed to the wind experience relatively higher pressure. Leeward areas and zones sheltered from the wind experience relatively lower pressure; openings between these zones can drive natural ventilation.

6
New cards

What characteristics make a structural parti effective for seismic design?

Use a regular, symmetrical plan and uniform loading; keep the building relatively low and wide with consistent floor heights and short spans; place shear walls or bracing near the perimeter; minimize large diaphragm openings; and provide a continuous lateral-force-resisting system from roof to foundation.

7
New cards

Why are cantilevers and irregular or re-entrant building plans problematic in seismic zones?

They create irregular mass, stiffness, or load paths. Building wings may move differently during an earthquake, concentrating stress at connections and re-entrant corners; irregular layouts can also produce unpredictable torsion.

8
New cards

Why do re-entrant corners concentrate seismic forces?

The wings on either side of the inside corner can move or twist out of phase during ground motion. Their connection at the notch becomes a stress concentration and may fail.

9
New cards

What seismic damage can occur at a re-entrant corner?

Differential movement between building wings concentrates stress at the notch. This can damage the connected structural elements and floor or roof diaphragm, as seen in documented L-shaped buildings.

10
New cards

How can re-entrant-corner problems be addressed in seismic design?

The preferred solution is to separate the wings with a seismic joint. Other strategies include stiffening the notch where the wings connect and strengthening wall elements at the ends and corners.

11
New cards

What building irregularities can lead to seismic failure?

Common vulnerabilities include a soft or weak story, excessive weight near the top, discontinuous or partial-height shear walls, abrupt changes in elevation, and floors with significantly different strength or stiffness. These create weak points in the lateral-force-resisting system.

12
New cards

What plan and diaphragm irregularities can increase seismic risk?

Examples include torsional irregularity, re-entrant corners, diaphragm eccentricity, nonparallel lateral-force-resisting systems, and out-of-plane offsets. These irregularities create additional forces and stress concentrations that require careful structural design.

13
New cards

Why must shear walls have limited openings and continue from roof to foundation?

Large or excessive openings reduce a shear wall’s stiffness and effectiveness. A wall that is discontinuous or does not extend to the foundation interrupts the lateral load path and can create a weak story under high lateral forces.

14
New cards

Can loam support a building, and which soils should generally be avoided for foundations?

Generally, yes: loam is a mixture of sand, silt, and clay and can provide suitable support. Avoid soils with substantial decaying organic matter (humus), such as topsoil and peat, because they are compressible and unstable. Confirm actual bearing conditions through geotechnical investigation.

15
New cards

How do Phase I and Phase II Environmental Site Assessments differ?

A Phase I ESA reviews historical records, site conditions, and interviews to identify recognized environmental conditions; it does not involve sampling. A Phase II ESA uses intrusive investigation—such as soil, groundwater, or building-material sampling—to determine whether contamination is present.

16
New cards

How can a body of water affect solar access?

An open water edge can create a clearing that allows direct and reflected solar gain.

17
New cards

How can trees benefit a building in a warm climate?

They provide shade and reduce solar heat gain.

18
New cards

What occupancy group is a courtroom?

Assembly Group A.

19
New cards

What occupancy group is a bank?

Business Group B.

20
New cards

What IBC occupancy group generally applies to a courtroom?

Assembly Group A, because a courtroom is a space where people gather. Confirm the specific classification and any applicable exceptions in the adopted code.

21
New cards

What IBC occupancy group generally applies to a bank?

Business Group B, which includes typical banking and office functions.

22
New cards

How can water pressure be increased in a gravity-fed plumbing system?

Increase the vertical distance between the water storage tank and the fixtures. The greater the water head, the greater the available static pressure.

23
New cards

How much vertical water head produces approximately 1 psi?

Approximately 2.31 feet of water column produces 1 psi.

24
New cards

Can you build in a floodplain?

Often, if local rules allow it and applicable floodplain requirements are met.

25
New cards

What is the annual chance of flooding in a 100-year floodplain?

1% in any given year.

26
New cards

What is the annual chance of flooding in a 500-year floodplain?

0.2% in any given year.

27
New cards

What is base flood elevation (BFE)?

The elevation floodwater is expected to reach during the base flood, commonly the 1%-annual-chance flood.

28
New cards

Where should new or substantially improved buildings be located relative to BFE?

The lowest floor and building equipment generally must be elevated above BFE under applicable flood rules.

29
New cards

How is a building efficiency ratio calculated?

Divide net area by gross building area. The result expresses the proportion of gross area that is usable for the intended program.

30
New cards

What is a typical target building efficiency ratio for an office?

About 75%, though the target varies by project.

31
New cards

What does net present value (NPV) measure?

NPV is the present value of expected future cash flows—benefits minus costs—after discounting them to account for the time value of money.

32
New cards

What does a positive net present value indicate?

A positive NPV means the discounted benefits exceed the initial and ongoing costs at the selected discount rate; the investment is expected to earn more than that required rate of return.

33
New cards

What does ASTM E1527 cover?

The standard practice for Phase I Environmental Site Assessments.

34
New cards

What does ASTM E1903 cover?

The standard practice for Phase II Environmental Site Assessments.

35
New cards

What does ASHRAE 55 address?

Thermal environmental conditions for human occupancy and comfort.

36
New cards

What does ASHRAE 62 address?

Ventilation and acceptable indoor air quality.

37
New cards

What does ASHRAE 90.1 address?

Energy efficiency requirements for buildings, including lighting and systems.

38
New cards

What do the Secretary of the Interior’s Standards address?

Standards for preservation, rehabilitation, restoration, and reconstruction of historic properties.

39
New cards

What is the first approach to improving energy performance in a historic building?

Start with minimally invasive weatherization and air-sealing measures.

40
New cards

How should insulation upgrades be prioritized in historic buildings?

Insulate attics, basements, and crawlspaces before disturbing finished historic spaces.

41
New cards

How should new additions relate to historic buildings?

Be compatible in scale and massing, distinguishable from the historic work, and removable without damaging it.

42
New cards

What is the basic approach to repairing historic masonry?

Repair deteriorated masonry and replace only what cannot be repaired; match compatible materials and methods.

43
New cards

What is the difference between a detention pond and a retention pond?

A detention pond temporarily stores stormwater and releases it at a controlled rate; it is typically dry between storm events. A retention pond maintains a permanent pool of water while also managing stormwater.

44
New cards

What is a retention pond?

A pond designed to hold a permanent pool of water and manage stormwater.

45
New cards

How does a bioswale manage stormwater?

A shallow, vegetated channel conveys runoff while slowing its flow and promoting filtration and infiltration.

46
New cards

How does a rain garden manage stormwater?

A planted depression captures runoff from nearby impervious surfaces and allows it to pond temporarily and infiltrate into the soil.

47
New cards

Why is compacted backfill used behind a retaining wall, and what else is required?

Compacted backfill provides a stable soil mass, but drainage is essential to prevent water from building up behind the wall. Provide drainage material and an outlet to relieve hydrostatic pressure.

48
New cards

Why is drainage required behind retaining walls?

Water trapped behind the wall creates hydrostatic pressure that adds lateral load and can cause movement or failure. Drainage relieves that pressure.

49
New cards

Which direction should fixed photovoltaic panels generally face in the Northern Hemisphere for maximum annual production?

Generally south, to maximize annual solar exposure. The optimal tilt and orientation still depend on latitude, shading, roof geometry, and the project’s energy goals.

50
New cards

What is the site-planning tradeoff between geothermal ground loops installed in trenches and wells?

Horizontal trenches require more land area but are generally shallower. Vertical wells use less surface area but require deeper drilling.

51
New cards

If zoning limits a building to three stories and building code allows five, how many stories are permitted?

Three; the more restrictive limit governs.

52
New cards

What does zoning commonly regulate besides building height?

Use, setbacks, lot coverage, density, parking, and other site-development standards.

53
New cards

What are form-based codes?

Zoning regulations that emphasize building form and its relationship to the public realm.

54
New cards

What is an easement?

A legal right to use another person’s land for a specific purpose.

55
New cards

What is a covenant?

A binding promise or restriction governing how land may be used.

56
New cards

How is floor-area ratio (FAR) calculated?

FAR = total counted building floor area ÷ lot area. The zoning ordinance determines which floor areas are included or excluded.

57
New cards

How does surface water move in relation to topographic contour lines?

Surface water flows downhill, generally perpendicular to contour lines, following the steepest descent.

58
New cards

How should a building site be graded to keep runoff away?

Slope the ground away from the building toward suitable drainage areas.

59
New cards

What is an authority having jurisdiction (AHJ)?

The agency or official responsible for interpreting and enforcing applicable codes.

60
New cards

Who enforces fire and life-safety requirements?

The AHJ, often through the fire marshal or fire department.

61
New cards

What is a single-loaded corridor?

A corridor with rooms on one side.

62
New cards

What is a double-loaded corridor?

A corridor with rooms on both sides.

63
New cards

How do horizontal louvers control solar gain?

Horizontal louvers are generally most effective against high-angle sun, especially on south-facing façades. Their projection and spacing determine how much sun is blocked.

64
New cards

How do vertical louvers control solar gain?

Vertical louvers are generally useful for low-angle sun, particularly on east- and west-facing façades, where horizontal overhangs are less effective.

65
New cards

Are overhangs or louvers generally more effective?

Both can be effective; the best choice depends on sun angle, orientation, and desired control.

66
New cards

What are the three broad climate categories in the commonly used U.S. climate-zone classification?

Moist (A), dry (B), and marine (C). Each category is further divided into temperature-based subgroups.

67
New cards

Where should site drains and catch basins be located?

At low points where runoff naturally collects, while avoiding building foundations.

68
New cards

Should a building’s open space or lake generally be north or south in a cold climate?

South, where it can preserve solar access to the building.

69
New cards

How should buildings be oriented in hot-humid climates?

Capture prevailing breezes and provide cross-ventilation; use shading to limit solar gain.

70
New cards

Where is a good building location on a hill?

Generally partway up the slope, avoiding both the valley bottom and exposed crest.

71
New cards

Which climates benefit most from air movement?

Hot-humid climates.

72
New cards

Which climates can benefit from evaporative cooling?

Hot-dry climates.

73
New cards

How is a site slope percentage calculated?

Slope (%) = vertical rise ÷ horizontal run × 100. Use the horizontal distance, not the length measured along the sloped surface.

74
New cards

What is the purpose of accessible routes in historic buildings?

Provide access while minimizing damage to significant historic features.

75
New cards

How should accessibility conflicts be handled in historic buildings?

Provide the greatest feasible accessibility while preserving character-defining features.

76
New cards

How should ramps at historic entrances be designed?

Use the least visually and physically intrusive accessible solution that meets applicable requirements.

77
New cards

What are common accessibility barriers in historic interiors?

Narrow doors and corridors, steps, inaccessible hardware, and level changes.

78
New cards

What does preservation mean under the Secretary of the Interior’s Standards?

Preservation focuses on sustaining and repairing the existing form, integrity, and materials of a historic property while retaining its historic character.

79
New cards

What does rehabilitation mean under the Secretary of the Interior’s Standards?

Rehabilitation adapts a historic property for a compatible contemporary use through repair, alterations, and additions while retaining its historic character-defining features.

80
New cards

What does restoration mean under the Secretary of the Interior’s Standards?

Restoration depicts a property at a particular period of time by removing features from other periods and reconstructing missing features from the restoration period.

81
New cards

What does reconstruction mean under the Secretary of the Interior’s Standards?

Reconstruction depicts, by means of new construction, a vanished or non-surviving building, site, landscape, or feature for interpretive purposes.

82
New cards

What is the steepest commonly cited slope for planted areas in this deck?

2:1, or 50%.

83
New cards

What is the maximum slope for a parking lot in this deck?

5%, or 1:20.

84
New cards

What is the road hierarchy from smallest to largest?

Local street, collector, arterial, freeway.

85
New cards

What is a rough order of magnitude (ROM) estimate?

An early, approximate cost estimate based on limited project information.

86
New cards

What are common urban development patterns?

Concentric zone, sector, and multiple-nuclei patterns.

87
New cards

What are common responses to a high water table?

Raise the building, use suitable foundation systems, and provide drainage or dewatering as appropriate.

88
New cards

What is a storage room generally classified as under the IBC?

It is typically classified by its actual use and hazard; use the code’s occupancy tables rather than assuming from room size.

89
New cards

Can you build in a riparian zone?

It depends on local regulations and environmental restrictions; development is often limited.

90
New cards

How do you calculate dwelling units for a site?

Multiply the site acreage by the target dwelling units per acre.

91
New cards

Where should a small building be located on a hill in a cold climate?

Avoid exposed high elevations; use a sheltered location while maintaining drainage.

92
New cards

What is a catch basin?

An underground box or inlet that collects surface runoff and directs it into a storm drain.

93
New cards

How does a patio-heater reflector work?

It directs radiant heat downward toward occupants.

94
New cards

What is the purpose of schematic design?

Establish the overall design concept, building organization, and approximate size and form.

95
New cards

What is the minimum slope for a swale in this deck?

1%.

96
New cards

What should you do if a site is too flat for gravity drainage?

Create positive grades with grading, swales, or engineered drainage systems.

97
New cards

What causes urban heat islands?

Dark surfaces, heat-absorbing materials, limited vegetation, and waste heat from buildings and vehicles.

98
New cards

How can urban heat islands be reduced?

Increase trees and vegetation, use reflective or high-albedo surfaces, and reduce waste heat.

99
New cards

What is universal design?

Design usable by people of a wide range of ages and abilities, without needing specialized adaptation.

100
New cards

What are common sources of light pollution?

Uplighting, unshielded fixtures, and excessive or misdirected lighting.