1/40
Comprehensive vocabulary flashcards covering blow molding processes, packaging foams, molecular film orientation, injection molding systems and calculations, and plastic sustainability concepts.
Blow Molding
A manufacturing process where air pressure is used to shape the inside of a hollow object while a mold shapes the outside; it is the only practical method to manufacture plastic bottles, jars, and large containers up to 55gal drums.
Parison
A hollow, tubular body of molten plastic extruded downward from a die during extrusion blow molding, which is captured by mold halves and inflated to create the container.
Preform
A test-tube-like injection-molded starting piece used in IBM and SBM that contains a pre-shaped, fully finished threaded neck and a bottom gate mark, designed to be reheated and expanded in a blow mold.
Cooling Stage (Blow Molding)
The rate-determining step in the blow molding process cycle that dictates and controls the operating speed of the blow molding machine.

Extrusion Blow Molding (EBM)
A blow molding method in which plastic resin is plasticated and extruded into a continuous or intermittent parison tube, closed in a mold, pinched at the bottom, and inflated by compressed air via a blow pin.

Parison Programming
The dynamic axial adjustment of a tapered mandrel or die pin during extrusion to vary the die gap opening from 0% to 100% over time, modifying parison wall thickness along its length to prevent thinning at high-expansion bottle areas.
Accumulator (EBM)
A heated auxiliary reservoir in intermittent extrusion blow molding that collects molten resin from the extruder before a tubular plunger drives it out rapidly, preventing premature cooling and sagging caused by gravity during large-part production.
Flash Line (Pinch-off Trim)
A raised seam along the base and handle areas of a blow-molded container, created where the halves of an extrusion blow mold clamp shut on the parison and weld the polymer shut while pinching off excess scrap.
Injection Blow Molding (IBM)
A two-stage blow molding process in which a preform is first injection-molded over a core pin in a primary mold set, and then transferred to a blow mold where air expands it into a finished container with high precision and no flash.
Stretch Blow Molding (SBM)
A blow molding variant that uses an internal stretch rod to axially elongate the preform prior to and during air blowing, redistributing resin to produce tall containers with biaxial molecular orientation, enhanced barrier, clarity, and impact strength.
Gate Mark
A distinct vestige or nub located at the base of injection-molded parts (including IBM and SBM bottles and preforms), signifying the point through which molten resin entered the mold cavity.

Open-Cell Foam
A cellular plastic structure composed of interconnecting, open communicating pathways between adjacent cells, enabling liquids and gases to pass directly through the foam matrix like a sponge.

Closed-Cell Foam
A cellular plastic structure where each gas-filled cell is completely enclosed and isolated by solid polymer walls, preventing liquid absorption and providing superior thermal insulation and buoyant properties.
Expanded Polystyrene (EPS)
A rigid, closed-cell foam manufactured by heating polystyrene beads impregnated with a hydrocarbon blowing agent (pentane) to vaporize the blowing agent, aging the pre-expanded beads, and fusing them together under heat and pressure inside a mold.
Extruded Polystyrene (XPS) Foam
A foam produced by melting polystyrene resin with a blowing agent and nucleator inside an extruder under pressure, expanding continuously upon exiting the die into sheets that are commonly thermoformed into meat trays and clamshells.
Foam-in-Place (Polyurethane)
A custom packaging method where liquid polyurethane chemicals are dispensed directly into a shipping container, covered with protective polyethylene film, and allowed to react and expand around a product to form an encapsulating cushion.
Polyolefin Foams (EPE / EPP)
Expanded or extruded foams made from polyethylene or polypropylene that are more flexible, less brittle, and more springy than polystyrene foams, providing superior multi-impact cushioning protection.
Starch-Based Foams
Loose-fill packaging materials derived from starch plasticized with water or other additives; marketed as environmentally friendly loose-fill shapes, but prone to moisture sorption and pest infestation.
Molecular Orientation
The stretching of a polymer web or preform at temperatures above its glass transition temperature (Tg) to align the polymer chains along the direction of draw, increasing tensile strength, stiffness, clarity, and barrier properties.
Tenter Frame
A mechanical stretching machine using diverging clip-driven chains inside heated ovens to grip the edges of a plastic sheet and apply transverse-direction (TD) stretch during biaxial film production.
Sequential Biaxial Orientation
A two-stage film orientation process where a cast polymer sheet is first drawn in the machine direction (MD) over speed-differential heated rollers, and subsequently stretched in the transverse direction (TD) on a tenter frame.
Simultaneous Biaxial Orientation
A tenter frame orientation method that draws a polymer film in both the machine direction (MD) and transverse direction (TD) at the same time, enabling wider draw ratios and relaxation in both directions for polymers like nylon.
Heat Setting
A thermal stabilization stage in film orientation where the stretched, restrained film is heated near its crystallization temperature to allow amorphous chains and tie molecules to relax while growing and refining crystallites, preventing shrinkage.
Double Bubble Process
A tubular film orientation process where an extruded primary tube is quenched, reheated, and expanded into a second bubble via internal air pressure and differential haul-off speeds to simultaneously impart biaxial orientation.
Reciprocating Screw
An injection unit screw that rotates to melt resin, shifts backward as molten plastic accumulates in front of the screw tip, and then moves forward like a hydraulic piston to inject the molten charge into the mold.
Non-Reciprocating Screw (Two-Stage)
An injection molding setup where an extruder screw continuously melts resin into a separate shooting pot, and a dedicated injection plunger forces the melt into the mold with high shot volume accuracy.
Sprue
The tapered primary channel in an injection mold that connects the machine nozzle directly to the runner system.
Runner
The distribution channels machined into an injection mold platen that convey molten polymer from the central sprue to individual mold cavities.
Gate (Injection Molding)
The small orifice connecting the runner to the mold cavity that restricts flow and quickly solidifies after cavity filling, leaving a small vestige or gate mark on the ejected part.
Balanced Flow Paths
A mold runner geometry configured so that molten polymer travels identical flow lengths and encounters equivalent resistance to every cavity, ensuring uniform filling and pressure across all parts.
Projected Area
The maximum cross-sectional silhouette area of a molded part viewed along the axis of mold clamping (facing the gate mark), used to determine clamping tonnage via Tonnage=2000lbs/tonProjected Area×Number of Cavities×Pressure×Safety Factor.
Clamping Unit
The mechanical or hydraulic mechanism of an injection molding machine that holds the mold platens closed against high injection pressures (commonly reaching up to 29,000psi) during resin injection.
Life Cycle Analysis (LCA)
A structured scientific methodology used to evaluate the overall environmental impact of a product across its entire life cycle, encompassing raw material extraction, manufacturing, distribution, use, recycling, and final disposal.
Greenwashing
A deceptive marketing practice involving unsubstantiated or misleading claims regarding the environmental benefits or sustainability attributes of a product, packaging material, or service.
Macrosorting
The initial sorting stage in mechanical recycling where whole, intact post-consumer packaging objects are separated manually or mechanically by color and resin type prior to any cleaning or size reduction.
Microsorting
The post-shredding separation of cleaned plastic flakes or regrind by resin density, typically executed in water sink-float separation tanks.
Molecular Sorting
A recycling technology that breaks down multi-material structures into individual polymer chains by dissolving them in organic solvents, isolating specific plastics at the molecular level.
Feedstock Recycling
A tertiary or chemical recycling process that uses thermal or chemical breakdown to reverse the polymerization reaction, converting plastics back into monomers or base petrochemical feedstocks to produce virgin-grade polymers like PET.
Biodegradable Polymers
Polymers (such as PHA) capable of being digested and completely metabolized by naturally occurring biological organisms under ambient environmental conditions into CO2, CH4, and H2O.
Compostable Polymers
Polymers (such as PLA) that break down via biological action only under controlled, elevated-temperature conditions provided by industrial composting systems, leaving no toxic residues or persistent microplastics.
Pyrolysis (Waste Plastic)
A thermochemical feedstock recycling process that decomposes mixed plastic waste at high temperatures in an oxygen-free atmosphere, producing synthetic oils, gases, and chemical feedstocks.