[L4] Storage, continuity and the flow equations

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/22

encourage image

There's no tags or description

Looks like no tags are added yet.

23 Terms

1
New cards

Specific yield, Sy [−]

• Applies to UNCONFINED aquifers • Volume of water released per unit area per unit fall in the water table elevation • The water comes from dewatering (draining) the pores as the water table is lowered • ΔV = Sy A Δz • Typically Sy ~ 0.01–0.3

2
New cards

Specific yield & drainable porosity

The water released as the water table falls comes from: • pores that were full becoming partially saturated • pores above the capillary fringe becoming less saturated • ΔV = A ∫₀^zs (θ(t1) − θ(t2)) dz (the area between the moisture profiles at t1 and t2) • Sy = ΔV / (A Δz) • Example: drained volume per unit area = 0.344 m for a 1.0 m decline → Sy = 0.344, against porosity n = 0.43 (Sy < n, because not all pore water drains) • Note: when water enters the aquifer (natural recharge or an injection well), the extra water raises the water table

3
New cards

Storativity, S [−]

• Applies to CONFINED aquifers • Volume of water released per unit area, over the entire aquifer thickness, per unit fall in the potentiometric surface • The water comes from a small reduction in aquifer porosity and fluid density caused by the drop in fluid pressure (NOT by drainage. The aquifer stays saturated.) • S = H Ss (H = aquifer thickness [L], Ss = specific storage coefficient [L⁻¹]) • ΔV = S A Δz

4
New cards

Sy vs S (typical values)

• Sy ~ 0.01–0.3 • S ~ 10⁻⁵–10⁻³ → S is 2 to 4 orders of magnitude smaller than Sy

5
New cards

What causes the change in storage (confined)

Effective stress and fluid pressure. • σT = σe + p (σT = total stress = weight per unit area of the ground and water column above a horizontal plane at depth z) • dσT = dσe + dp • If dσT = 0 → dσe = −dp • σe: grain pushes on grain. p: pore water pushes. • Pumping → fluid pressure falls (dp < 0) while the ground above weighs the same (dσT = 0) → effective stress rises → grains squeeze together → small decrease in porosity n (Grain-scale view after Price, 1987)

6
New cards

Mass continuity: control volume

Control volume Δx Δy Δz over time Δt. Fluid density ρ [M L⁻³], fluid flux qx, qy, qz [L T⁻¹] • Change in storage = mass in − mass out • For x faces: in = Δy Δz Δt ρqx, out = Δy Δz Δt [ρqx + Δ(ρqx)] • Δx Δy Δz Δm = −Δy Δz Δt Δ(ρqx) − Δx Δz Δt Δ(ρqy) − Δx Δy Δt Δ(ρqz) • m [M L⁻³] = fluid mass per unit volume • Divide by Δx Δy Δz Δt: Δm/Δt = −Δ(ρqx)/Δx − Δ(ρqy)/Δy − Δ(ρqz)/Δz • In the limit (PDE): ∂m/∂t = −∂(ρqx)/∂x − ∂(ρqy)/∂y − ∂(ρqz)/∂z

7
New cards

What causes the change in mass, Δm

  1. Increase in fluid density from compression, Δρ [M L⁻³] (from an increase in fluid pressure)
  2. Increase in porosity from rock matrix expansion, Δn [−] (from a decrease in effective stress) • m = nρ → product rule: ∂m/∂t = ∂(nρ)/∂t = ρ ∂n/∂t + n ∂ρ/∂t • Assume n and ρ are uniquely defined by p → chain rule: = ρ (dn/dp)(∂p/∂t) + n (dρ/dp)(∂p/∂t) = nρ [(1/n)(dn/dp) + (1/ρ)(dρ/dp)] ∂p/∂t • dp = ρg dh (z constant) → ∂m/∂t = nρg [(1/n)(dn/dp) + (1/ρ)(dρ/dp)] ∂(ρh)/∂t
8
New cards

Rock & fluid compressibility

• Rock compressibility: cR = (1/n)(dn/dp) [M⁻¹ L T²], i.e. Pa⁻¹ • Fluid compressibility: cF = (1/ρ)(dρ/dp) [M⁻¹ L T²], i.e. Pa⁻¹ • → ∂m/∂t = nρg (cR + cF) ∂(ρh)/∂t

9
New cards

Specific storage coefficient, Ss [L⁻¹]

• Ss = nρg (cR + cF) • Ss ∂(ρh)/∂t = −∂(ρqx)/∂x − ∂(ρqy)/∂y − ∂(ρqz)/∂z • The fluid is only very slightly compressible, so ρ is effectively constant: → Ss ∂h/∂t = −∂qx/∂x − ∂qy/∂y − ∂qz/∂z (3D continuity equation)

10
New cards

Typical compressibility values (Pa⁻¹)

(Values are n·cR, i.e. multiplied by porosity, except water) • Plastic clay: 2.0 × 10⁻⁶ to 2.6 × 10⁻⁷ • Stiff clay: 2.6 × 10⁻⁷ to 1.3 × 10⁻⁷ • Medium-hard clay: 1.3 × 10⁻⁷ to 6.9 × 10⁻⁸ • Loose sand: 1.0 × 10⁻⁷ to 5.2 × 10⁻⁸ • Dense sand: 2.0 × 10⁻⁸ to 1.3 × 10⁻⁸ • Dense, sandy gravel: 1.0 × 10⁻⁸ to 5.2 × 10⁻⁹ • Rock, fissured: 6.9 × 10⁻¹⁰ to 3.3 × 10⁻¹⁰ • Rock, sound: < 3.3 × 10⁻¹⁰ • Water at 25 °C: 4.8 × 10⁻¹⁰ (Schwartz & Zhang, 2003)

11
New cards

3D transient flow equation (confined)

Substitute Darcy's law into the continuity equation: Ss ∂h/∂t = ∂/∂x(Kx ∂h/∂x) + ∂/∂y(Ky ∂h/∂y) + ∂/∂z(Kz ∂h/∂z)

12
New cards

Reducing to the 2D confined aquifer equation

• Vertical flow is often assumed negligible • Integrate over the aquifer thickness from z0 to z0 + H: ∫ Ss ∂h/∂t dz = ∫ [∂/∂x(Kx ∂h/∂x) + ∂/∂y(Ky ∂h/∂y) + ∂/∂z(Kz ∂h/∂z)] dz • Vertical term drops out because Kz ∂h/∂z = 0 at both confining beds (no-flow boundaries) • Assume Kx, Ky, Ss and h are constant in z: → H Ss ∂h/∂t = ∂/∂x(H Kx ∂h/∂x) + ∂/∂y(H Ky ∂h/∂y)

13
New cards

2D confined aquifer equation (S and T)

Horizontal flow in confined aquifers is described with the bulk parameters storativity S [−] and transmissivity T [L² T⁻¹]: • S ∂h/∂t = ∂/∂x(Tx ∂h/∂x) + ∂/∂y(Ty ∂h/∂y) • S = H Ss, Tx = H Kx, Ty = H Ky (per unit plan area)

14
New cards

MODFLOW

USGS computer program for solving the groundwater flow equation: ∂/∂x(T ∂h/∂x) + ∂/∂y(T ∂h/∂y) − W = S ∂h/∂t • T terms = flow in and out (transmissivity) • W = wells and recharge • S ∂h/∂t = change in storage • MODFLOW 6 solves it by the finite-difference method on a grid of cells: one head h per cell (row i, column j, layer k from the top), flow to each neighbour by Darcy's law, cell width Δx = DELR • Rivers modelled as head-dependent cells; boundaries can be fixed head (Langevin et al., 2017)

15
New cards

FloPy example: valley aquifer

• Winter recharge raises the water table • → raises the baseflow into the stream • Outflow peaks at the end of February, about 6 weeks after the recharge, then recedes through the summer • Shows seasonal storage: the aquifer stores winter recharge and releases it slowly

16
New cards

Transient unconfined flow: continuity

(Sy + (h − zb) Ss) Δx Δy Δh = flow in − flow out + (R − Qa) Δx Δy Δt • Flow in x: Δy (h − zb) qx Δt, out: Δy [(h − zb) qx + Δ((h − zb) qx)] Δt (same for y) • Sy = wetting of pores as the water table rises • (h − zb) Ss = water added through elastic storage • h − zb = saturated thickness (zb = aquifer base) • Reduces to: (Sy + (h − zb) Ss) Δh/Δt = −Δ((h − zb) qx)/Δx − Δ((h − zb) qy)/Δy + R − Qa • Usually Sy ≫ (h − zb) Ss, so: → Sy ∂h/∂t = −∂((h − zb) qx)/∂x − ∂((h − zb) qy)/∂y + R − Qa

17
New cards

Unconfined flow: key points

• Storage released = Sy Δh per unit area (specific yield, NOT storativity) • Saturated thickness (h − zb) is part of the answer, so T = K(h − zb) moves as the water table moves → the equation is NON-LINEAR • Dupuit assumptions → only need to consider flow in x and y • Recharge typically needs to be modelled

18
New cards

Boussinesq equation

Transient unconfined flow. Substitute Darcy (qi = −Ki ∂h/∂i, i = x, y): Sy ∂h/∂t = ∂/∂x[(h − zb) Kx ∂h/∂x] + ∂/∂y[(h − zb) Ky ∂h/∂y] + R − Qa • R = recharge, Qa = abstraction, both rates per unit plan area, m/s [L T⁻¹] • Non-linear: transmissivity (h − zb)K depends on the head being solved for → no general analytical solution, so unconfined problems are usually solved numerically

19
New cards

Groundwater modelling process

  1. Understand the system
  2. Conceptual model: description in words and pictures. Geology, hydrogeology, boundaries: gw divide, outcrop/impermeable, aquicludes (no flow), recharge (flow), sea/lakes, rivers/springs (head control)
  3. Mathematical model: the flow equation (e.g. Boussinesq)
  4. Parameters: surface topography, aquifer base topography (zb), boundary types, rainfall/evaporation → recharge (R), K/T, S/Sy, rivers/springs, abstractions (Qa)
  5. Numerical solution
20
New cards

Example: pumping next to the River Thames

• Gatehampton: multiple-well abstraction, peak licence for the whole site 105 ML/d (Thames Water & BGS) • Regional model provides the boundary conditions • A local model is then used to examine local behaviour

21
New cards

Barometric effects on confined piezometers

• Barometric pressure rises → the extra load on a confined aquifer is carried partly by the grain skeleton and partly by the water • The water in the open piezometer feels the full increase directly → Water level in the well FALLS when the barometer RISES • Left uncorrected, the error can be tens of centimetres → a barometric logger is essential • A well that responds to the barometer is telling you the aquifer is confined

22
New cards

Barometric efficiency, BE

• BE = −ρg Δh / Δpa (Δpa = change in atmospheric pressure) • Typically 0.2–0.75 for confined aquifers • Effectively zero for unconfined aquifers

23
New cards

Hydraulic diffusivity, Dh

• Dh = T / S • Units: m²/d (or m²/s) (From Tutorial