1/199
Looks like no tags are added yet.
What is the main goal of patient radiation protection?
A) Eliminate all dental imaging
B) Minimize radiation received while maximizing diagnostic benefit
C) Use only extraoral imaging
D) Increase exposure time for clearer images
B) Minimize radiation received while maximizing diagnostic benefit
— Patient protection aims to minimize radiation while preserving the diagnostic benefit.
Before x-ray exposure, which action helps minimize patient radiation?
A) Predetermine the same images for every patient
B) Prescribe images based on individual need
C) Use the longest exposure time
D) Avoid reviewing the patient's history
B) Prescribe images based on individual need
— Dental images should be prescribed according to the individual patient's needs.
Who is responsible for prescribing dental images?
A) Dental assistant
B) Dental hygienist
C) Dentist
D) Equipment manufacturer
C) Dentist
— The dentist uses professional judgment to determine the number, type, and frequency of images.
Which combination is part of proper x-ray equipment for patient protection?
A) Aluminum filters, lead collimator, and PID
B) Plastic cone, steel filter, and timer
C) Lead filter, copper cone, and sensor
D) Film holder, apron, and darkroom light
A) Aluminum filters, lead collimator, and PID
— The tubehead should include aluminum filtration, a lead collimator, and a position-indicating device.
Inherent filtration occurs as the primary beam passes through the:
A) Lead apron and thyroid collar
B) Glass window, insulating oil, and tubehead seal
C) Collimator only
D) Patient and receptor
B) Glass window, insulating oil, and tubehead seal
— These tubehead components provide inherent filtration.
Inherent filtration is approximately equivalent to how much aluminum?
A) 0.5–1.0 mm
B) 1.5–2.0 mm
C) 2.5–3.0 mm
D) 4.0–5.0 mm
A) 0.5–1.0 mm
— Inherent filtration is about 0.5 to 1.0 mm aluminum equivalent.
Why is added filtration necessary?
A) Inherent filtration alone does not meet required standards
B) It increases low-energy x-rays
C) It enlarges the beam
D) It replaces the collimator
A) Inherent filtration alone does not meet required standards
— Inherent filtration alone does not satisfy state and federal requirements.
Added filtration is typically provided by:
A) Lead disks
B) Aluminum disks
C) Plastic sheets
D) Copper wires
B) Aluminum disks
— Aluminum disks are placed in the path of the x-ray beam.
Added filtration primarily removes which x-rays?
A) Short-wavelength, high-energy x-rays
B) Long-wavelength, low-energy x-rays
C) All x-rays equally
D) Only scattered x-rays after they reach the patient
B) Long-wavelength, low-energy x-rays
— Low-energy, longer-wavelength x-rays add dose without useful diagnostic value.
Filtration results in a useful beam that is:
A) Lower energy and less penetrating
B) Higher energy and more penetrating
C) Wider and more divergent
D) Completely free of radiation
B) Higher energy and more penetrating
— Removing low-energy photons makes the remaining beam more penetrating.
Total filtration is the sum of:
A) kVp and mA
B) Inherent and added filtration
C) Collimation and shielding
D) Distance and exposure time
B) Inherent and added filtration
— Total filtration includes both inherent and added filtration.
Dental x-ray machines operating at or below 70 kVp require at least:
A) 0.5 mm aluminum filtration
B) 1.0 mm aluminum filtration
C) 1.5 mm aluminum filtration
D) 2.5 mm aluminum filtration
C) 1.5 mm aluminum filtration
— At or below 70 kVp, the minimum total filtration is 1.5 mm aluminum.
Dental x-ray machines operating above 70 kVp require at least:
A) 1.0 mm aluminum filtration
B) 1.5 mm aluminum filtration
C) 2.0 mm aluminum filtration
D) 2.5 mm aluminum filtration
D) 2.5 mm aluminum filtration
— Above 70 kVp, the minimum total filtration is 2.5 mm aluminum.
What is the main purpose of collimation?
A) Increase film speed
B) Restrict the size and shape of the x-ray beam
C) Increase scatter radiation
D) Lengthen exposure time
B) Restrict the size and shape of the x-ray beam
— Collimation limits the beam and reduces unnecessary patient exposure.
A round collimator produces a cone-shaped beam about:
A) 1.0 inch in diameter
B) 2.0 inches in diameter
C) 2.75 inches in diameter
D) 4.0 inches in diameter
C) 2.75 inches in diameter
— The circular beam is limited to about 2.75 inches at the patient's skin.
A rectangular collimator produces a beam that is:
A) Slightly larger than a size 2 receptor
B) Larger than the patient's face
C) Exactly 2.75 inches round
D) Smaller than any intraoral receptor
A) Slightly larger than a size 2 receptor
— Rectangular collimation limits the field to just beyond a size 2 receptor.
Compared with circular collimation, rectangular collimation:
A) Exposes more tissue
B) Exposes less tissue
C) Has no effect on exposure
D) Requires a pointed cone
B) Exposes less tissue
— Rectangular collimation reduces the area of tissue exposed.
Where is the collimator located?
A) Between the x-ray tube and the PID
B) Inside the control panel
C) Inside the patient's mouth
D) Behind the receptor
A) Between the x-ray tube and the PID
— The collimator is positioned in the tubehead beam path before the PID.
What is the function of the PID?
A) Process the image
B) Direct the x-ray beam
C) Measure patient dose
D) Hold the receptor in the mouth
B) Direct the x-ray beam
— The position-indicating device directs the x-ray beam.
Why are pointed plastic conical PIDs no longer used?
A) They are too heavy
B) They produce excess scatter radiation
C) They cannot direct the beam
D) They over-filter the beam
B) They produce excess scatter radiation
— The pointed plastic cone produced scatter radiation.
Which PIDs are currently used in dentistry?
A) Closed pointed plastic only
B) Open-ended round and rectangular
C) Triangular and oval only
D) Lead-free conical only
B) Open-ended round and rectangular
— Modern PIDs are open-ended and typically round or rectangular.
Why are modern PIDs lead-lined?
A) To increase scatter
B) To limit scatter radiation
C) To raise mA
D) To shorten processing time
B) To limit scatter radiation — Lead lining helps limit production of scatter radiation.
Common PID lengths are:
A) 4 and 6 inches
B) 6 and 10 inches
C) 8 and 16 inches
D) 12 and 24 inches
C) 8 and 16 inches
— Short and long PIDs are commonly 8 and 16 inches.
Which PID length is preferred for reducing beam divergence?
A) 8-inch
B) 10-inch
C) 12-inch
D) 16-inch
D) 16-inch
— The 16-inch PID produces less beam divergence.
Which PID shape is most effective in reducing patient exposure?
A) Rectangular
B) Conical
C) Pointed plastic
D) Open circular only
A) Rectangular
— The rectangular PID best limits the exposed area.
During exposure, which device protects the thyroid from scatter radiation?
A) Beam alignment device
B) Thyroid collar
C) Control panel
D) Receptor holder
B) Thyroid collar
— The thyroid collar shields the thyroid gland from scatter.
The thyroid collar is recommended for:
A) All intraoral exposures
B) Only panoramic exposures
C) Only extraoral exposures
D) No dental exposures
A) All intraoral exposures
— The source material recommends the thyroid collar for intraoral exposures.
Why is a thyroid collar generally not recommended for extraoral exposures?
A) It increases kVp
B) It can obscure information and make the image nondiagnostic
C) It cannot block scatter
D) It damages the receptor
B) It can obscure information and make the image nondiagnostic
— The collar may interfere with extraoral image formation.
A lead apron protects mainly:
A) Only the thyroid
B) Reproductive and blood-forming tissues from scatter
C) The x-ray tube
D) The receptor from light
B) Reproductive and blood-forming tissues from scatter
— The apron is placed over the chest and lap to shield radiosensitive tissues.
Lead aprons should be stored:
A) Folded tightly
B) Rolled into a small drawer
C) Without folding or creasing
D) Under the x-ray tubehead
C) Without folding or creasing
— Folding can create cracks in the protective material.
Which receptor type requires the least patient radiation exposure according to the chapter?
A) Traditional D-speed film
B) Digital receptor
C) Occlusal film
D) Duplicating film
B) Digital receptor
— Digital receptors are identified as the most effective receptor method for reducing exposure.
When digital sensors are not used, which film is preferred to reduce patient dose?
A) Slow film
B) D-speed film only
C) Fast film
D) Duplicating film
C) Fast film
— Fast film reduces the exposure needed.
Which is faster, D-speed or F-speed film?
A) D-speed
B) F-speed
C) They are identical
D) Neither is used
B) F-speed
— F-speed is the faster of the two.
The main factor determining film speed is the size of the:
A) Lead foil sheets
B) Silver bromide crystals
C) Plastic packet
D) Collimator opening
B) Silver bromide crystals
— Larger silver bromide crystals make film faster.
A slight disadvantage of F-speed film is:
A) More patient radiation
B) Slightly decreased contrast
C) Greater beam divergence
D) Longer processing time is always required
B) Slightly decreased contrast
— The larger crystals may produce slightly decreased contrast.
A beam alignment device primarily:
A) Stabilizes the receptor and helps align the beam
B) Raises kVp
C) Filters low-energy photons
D) Measures MPD
A) Stabilizes the receptor and helps align the beam
— It stabilizes the receptor and helps position the PID correctly.
Using a beam alignment device reduces the need for the patient to:
A) Wear a thyroid collar
B) Hold the receptor with a finger
C) Sit upright
D) Remove jewelry
B) Hold the receptor with a finger
— The device stabilizes the receptor so the patient's finger does not need to hold it.
What may be used to help stabilize a film holder in an area of missing teeth?
A) Lead foil
B) Cotton rolls
C) Aluminum disks
D) Sterile water
B) Cotton rolls
— Cotton rolls may help support the film-holding instrument.
Exposure factor selection involves adjustment of:
A) kVp, mA, and time
B) Only film speed
C) Collimator shape only
D) Apron thickness and PID color
A) kVp, mA, and time
— kVp, milliamperage, and exposure time determine x-ray output.
According to the slide content, what kVp range helps keep patient exposure to a minimum?
A) 20–40 kVp
B) 40–50 kVp
C) 60–80 kVp
D) 100–120 kVp
C) 60–80 kVp
— The highlighted teaching point gives a range of 60 to 80 kVp.
Why should nondiagnostic images be avoided?
A) They increase filtration
B) They may require retakes and additional radiation
C) They lower film speed
D) They eliminate scatter
B) They may require retakes and additional radiation
— Retakes add unnecessary radiation exposure.
A major cause of unnecessary radiation exposure in dental imaging is:
A) Rectangular collimation
B) Retakes
C) Digital sensors
D) Long PIDs
B) Retakes
— Retakes are specifically identified as a major source of unnecessary exposure.
After exposure, careful receptor handling is important because:
A) Artifacts may make images nondiagnostic
B) It increases beam energy
C) It controls mA
D) It replaces filtration
A) Artifacts may make images nondiagnostic
— Improper handling can cause artifacts and lead to repeat exposures.
Improper film processing may result in:
A) Less need for retakes
B) A nondiagnostic image requiring retake
C) Increased filtration
D) Reduced scatter at the tubehead
B) A nondiagnostic image requiring retake
— Processing errors can make an image unusable and require another exposure.
The dental radiographer should avoid occupational exposure by:
A) Standing in the primary beam
B) Maintaining distance, proper position, and shielding
C) Holding the receptor for every patient
D) Increasing exposure time
B) Maintaining distance, proper position, and shielding
— Operator protection depends on avoiding the primary beam and using distance and shielding.
Ideally, during exposure the radiographer should:
A) Stand next to the patient without shielding
B) Leave the room or stand behind a suitable barrier
C) Hold the PID
D) Stand directly behind the receptor
B) Leave the room or stand behind a suitable barrier
— Leaving the room or using a protective barrier minimizes operator exposure.
If adequate distance cannot be maintained, the operator should:
A) Use a protective barrier
B) Increase kVp
C) Remove filtration
D) Use a shorter PID
A) Use a protective barrier
— A suitable protective barrier is required when distance cannot be maintained.
A radiation-monitoring badge is used to:
A) Direct the beam
B) Measure occupational radiation exposure
C) Hold the receptor
D) Set the timer
B) Measure occupational radiation exposure
— Monitoring badges track radiation received by personnel.
Radiation monitoring devices are commonly worn:
A) On the patient's wrist
B) On the operator's clothing, such as a breast pocket
C) Inside the PID
D) On the receptor
B) On the operator's clothing, such as a breast pocket
— The small badge can be worn on the operator's work clothing.
Radiation monitoring badges are typically:
A) Never sent for analysis
B) Periodically sent to an agency for exposure reports
C) Used to filter the beam
D) Placed on the patient
B) Periodically sent to an agency for exposure reports
— They are processed by a monitoring service that reports exposure.
The Radiation Control for Health and Safety Act was passed in:
A) 1948
B) 1958
C) 1968
D) 1981
C) 1968
— The slide identifies the Radiation Control for Health and Safety Act of 1968.
The Consumer-Patient Radiation Health and Safety Act was passed in:
A) 1968
B) 1974
C) 1981
D) 1991
C) 1981
— The slide identifies this act as 1981.
MPD stands for:
A) Maximum permissible dose
B) Minimum patient distance
C) Measured photon density
D) Maximum processing duration
A) Maximum permissible dose
— MPD is the maximum dose equivalent permitted in a specified period.
The annual MPD for occupationally exposed persons is:
A) 1 mSv/year
B) 5 mSv/year
C) 10 mSv/year
D) 50 mSv/year
D) 50 mSv/year
— The chapter gives 50 mSv per year for occupational exposure.
The annual MPD for nonoccupationally exposed persons is:
A) 0.5 mSv/year
B) 1 mSv/year
C) 5 mSv/year
D) 50 mSv/year
B) 1 mSv/year
— The chapter gives 1 mSv per year for nonoccupationally exposed persons.
The MPD for an occupationally exposed pregnant worker is:
A) 0.5 mSv per month during pregnancy
B) 5 mSv per month
C) 50 mSv per month
D) 1 mSv per day
A) 0.5 mSv per month during pregnancy
— The chapter specifies 0.5 mSv per month during pregnancy.
Cumulative occupational dose refers to:
A) Dose from a single exposure
B) Dose accumulated over a lifetime
C) Dose received only by patients
D) Scatter from one image
B) Dose accumulated over a lifetime
— It is the total occupational dose accumulated over time.
A worker's cumulative occupational effective dose should not exceed:
A) Age × 1 mSv
B) Age × 5 mSv
C) Age × 10 mSv
D) Age × 50 mSv
C) Age × 10 mSv
— The slide states age multiplied by 10 mSv.
According to the chapter, the minimum age for a person who works with radiation is:
A) 16
B) 17
C) 18
D) 21
C) 18
— The slide states 18 years.
For a 60-year-old radiation worker, the recommended cumulative occupational dose limit is:
A) 60 mSv
B) 300 mSv
C) 600 mSv
D) 3000 mSv
C) 600 mSv
— 60 × 10 mSv equals 600 mSv.
ALARA means radiation exposure should be kept:
A) As low as reasonably achievable
B) At the legal maximum
C) Above 70 kVp at all times
D) At zero by eliminating all imaging
A) As low as reasonably achievable
— ALARA is the principle of minimizing exposure while accomplishing necessary imaging.
Which action follows ALARA?
A) Order images only for diagnostic purposes
B) Take a full-mouth series at every visit
C) Use the shortest PID
D) Repeat every imperfect image
A) Order images only for diagnostic purposes
— Images should be prescribed only when diagnostically justified.
Which receptor choice best follows ALARA?
A) Slow film only
B) F-speed film or digital imaging
C) Duplicating film
D) Any film if exposure time is increased
B) F-speed film or digital imaging — Fast film and digital imaging reduce required exposure.
Which equipment choice best follows ALARA?
A) Short pointed PID
B) Long rectangular PID
C) No collimator
D) Wide circular beam only
B) Long rectangular PID
— A longer PID and rectangular beam reduce divergence and exposed tissue.
Which practice best follows ALARA?
A) Avoid retakes
B) Increase exposure time routinely
C) Have patients hold receptors with fingers
D) Remove aluminum filtration
A) Avoid retakes
— Avoiding retakes prevents unnecessary additional exposure.
Patient education about radiation protection should explain:
A) Only what happens after exposure
B) Protection before, during, and after exposure
C) Only equipment brand names
D) Only legal dose limits
B) Protection before, during, and after exposure
— The radiographer should be able to explain protection throughout the entire procedure.
Before exposure, patient protection includes:
A) Proper prescribing and proper equipment
B) Only processing film
C) Only wearing a monitoring badge
D) Only surface disinfection
A) Proper prescribing and proper equipment
— These are the major pre-exposure protection measures.
During exposure, patient protection includes:
A) Thyroid collar, lead apron, appropriate receptor, beam alignment, proper factors, and technique
B) Only darkroom processing
C) Only operator monitoring
D) Only patient education
A) Thyroid collar, lead apron, appropriate receptor, beam alignment, proper factors, and technique
— These measures reduce dose and the need for repeats during exposure.
After exposure, patient protection includes:
A) Careful receptor handling and proper processing/image retrieval
B) Changing kVp
C) Replacing the collimator
D) Increasing mA
A) Careful receptor handling and proper processing/image retrieval
— Correct handling and processing prevent nondiagnostic images and retakes.
Which statement best reflects the relationship between dental imaging benefits and radiation risk in the chapter?
A) Properly prescribed imaging benefits can outweigh the small radiation risk
B) Radiation risk always exceeds diagnostic benefit
C) Dental images have no diagnostic benefit
D) Every patient should receive the same number of images
A) Properly prescribed imaging benefits can outweigh the small radiation risk
— The source emphasizes individualized, justified imaging whose diagnostic benefit outweighs the small exposure risk.
Before what year were there no federal standards for manufacture of dental x-ray machines?
A) 1954
B) 1964
C) 1974
D) 1984
C) 1974
— Federal manufacturing standards began in 1974.
Since 1974, who regulates the manufacture and installation of dental x-ray equipment?
A) Federal government
B) Patients
C) Only equipment manufacturers
D) Only dental assistants
A) Federal government
— Federal regulation applies to manufacture and installation.
Who regulates how dental x-ray equipment is used?
A) Only the federal government
B) State and local governments
C) Only the dentist
D) Only the manufacturer
B) State and local governments
— State and local governments dictate use and applicable radiation codes.
Depending on local codes, dental x-ray equipment may need to be:
A) Registered, inspected, and monitored periodically
B) Replaced every year
C) Used only in hospitals
D) Operated without a control panel
A) Registered, inspected, and monitored periodically
— Registration, inspection, and monitoring may be required.
Intraoral receptors are positioned:
A) Inside the mouth
B) Outside the mouth
C) Behind the operator
D) Inside the tubehead
A) Inside the mouth
— Intraoral receptors are used inside the oral cavity.
Extraoral receptors are positioned:
A) Inside the mouth
B) Outside the mouth
C) Inside the PID
D) Under the lead apron
B) Outside the mouth
— Extraoral receptors are used outside the mouth.
Portable intraoral x-ray units are especially useful for:
A) Only darkroom processing
B) Exposures outside the dental office
C) Replacing all extraoral units
D) Sterilizing instruments
B) Exposures outside the dental office
— Portable units allow imaging in locations such as nursing homes and mobile clinics.
Portable dental x-ray units are typically:
A) Battery powered
B) Steam powered
C) Film powered
D) Manually cranked
A) Battery powered
— The handheld units are battery powered.
Portable dental x-ray units have been approved for dental use by the:
A) CDC only
B) FDA
C) NCRP only
D) ADA only
B) FDA
— The slides identify FDA approval.
Portable x-ray units are approved:
A) In all states without exception
B) In many, but not all, states
C) In no states
D) Only outside the United States
B) In many, but not all, states
— State radiation boards determine whether and how they may be used.
Operator exposure from a handheld x-ray unit is limited by:
A) A lead acrylic disk shield around the PID
B) A pointed plastic cone
C) Removing the PID
D) Using no collimation
A) A lead acrylic disk shield around the PID
— The disk shield minimizes backscatter from the patient.
Which are the three main components of a typical intraoral x-ray machine?
A) Tubehead, extension arm, control panel
B) Sensor, apron, keyboard
C) PID, film, darkroom
D) Tubehead, chair, developer
A) Tubehead, extension arm, control panel
— These are the three standard intraoral unit components.
Which component contains the x-ray tube?
A) Control panel
B) Tubehead
C) Extension arm
D) Receptor holder
B) Tubehead
— The tubehead houses the x-ray tube.
The extension arm primarily:
A) Processes images
B) Suspends and positions the tubehead and houses electrical wires
C) Measures MPD
D) Sterilizes receptors
B) Suspends and positions the tubehead and houses electrical wires
— It supports the tubehead and allows its movement.
The control panel allows the radiographer to:
A) Regulate the x-ray beam
B) Sterilize the PID
C) Hold the receptor
D) Filter saliva
A) Regulate the x-ray beam
— The control panel includes the operating controls for exposure.
The on-off switch on the control panel:
A) Activates film processing
B) Must be on to operate the x-ray unit
C) Controls collimator shape
D) Measures scatter
B) Must be on to operate the x-ray unit
— The unit cannot be operated unless the switch is on.
The exposure button:
A) Activates the machine to produce x-rays
B) Changes film speed
C) Sterilizes the receptor
D) Moves the patient chair
A) Activates the machine to produce x-rays
— Firmly depressing it initiates x-ray production.
During x-ray production, the control panel typically provides:
A) Only a smell
B) A visible exposure light and an audible beep
C) No indication
D) A flashing receptor
B) A visible exposure light and an audible beep
— Light and sound indicate that x-rays are being produced.
The timer controls:
A) Beam shape
B) Length of exposure time
C) Film crystal size
D) Patient positioning
B) Length of exposure time
— The timer determines exposure duration.
kV and mA selectors allow the radiographer to adjust:
A) Kilovoltage and milliamperage
B) Processing temperature and time
C) Collimator shape and PID length
D) Chair height and headrest
A) Kilovoltage and milliamperage
— They control beam energy and tube current settings.
Preset programmable settings may be based on:
A) Anatomic area and patient size
B) Operator age only
C) Film packet color only
D) Room temperature only
A) Anatomic area and patient size
— Many units provide presets for regions and patient sizes.
Which is a main component of an extraoral x-ray machine?
A) Tubehead
B) Darkroom timer only
C) Autoclave
D) Film duplicator
A) Tubehead
— Extraoral systems include a tubehead, positioning devices, and control panel.
Extraoral positioning devices may stabilize the:
A) Lateral head, chin, forehead, and anterior teeth
B) Only the hands
C) Only the shoulders
D) Only the thyroid
A) Lateral head, chin, forehead, and anterior teeth
— These positioning supports help align and stabilize the patient.
In many extraoral machines, the tubehead and receptor are:
A) On the same side
B) On opposite sides of the patient
C) Both inside the mouth
D) Both in the control panel
B) On opposite sides of the patient
— The x-ray source is typically on one side and detector on the opposite side.
Head-stabilizing devices on extraoral machines help:
A) Keep the patient correctly positioned and still
B) Increase scatter
C) Shorten the PID
D) Filter low-energy photons
A) Keep the patient correctly positioned and still
— Stabilization is important during the longer extraoral exposure.
A receptor holder is used to:
A) Hold and align an intraoral receptor
B) Control kVp
C) Measure occupational dose
D) Filter x-rays
A) Hold and align an intraoral receptor
— It stabilizes the receptor in the mouth.
Receptor holders eliminate the need for the patient to:
A) Wear PPE
B) Stabilize the receptor with a finger
C) Remove jewelry
D) Sit in the chair
B) Stabilize the receptor with a finger
— The holder supports the receptor.
Which intraoral technique specifically requires a receptor-holding device according to the chapter?
A) Paralleling technique
B) Freehand extraoral technique
C) Panoramic technique
D) Cephalometric technique
A) Paralleling technique
— A receptor holder is required for the paralleling technique.
A beam alignment device helps position the:
A) PID in relation to the tooth and receptor
B) Patient's apron only
C) Darkroom safelight
D) Monitoring badge
A) PID in relation to the tooth and receptor
— Its purpose is beam/receptor/tooth alignment.
The simplest receptor holder described is a:
A) Disposable Styrofoam bite-block
B) Metal forceps
C) Lead disk
D) Plastic cone
A) Disposable Styrofoam bite-block — The chapter lists a simple disposable Styrofoam bite-block with backing plate and slot.