1/100
Looks like no tags are added yet.
Coolant Reservoir
The fluid level should be in the proper range on the sight glass. All compartments and latches should be secure.
Leaks & Engine Hatch
The engine hatch door should not be damaged and should latch securely. There are no leaks or puddles (or if there is a puddle, inspect to see if it is water).
Power Steering Fluid
For the bus to be safe to operate, the fluid should be between the add and full lines on the sight glass (or visible in the round sight glass). The power steering is gear-driven, so there is no power steering belt.
Hoses
The hoses are secure, not cracked or broken, and not leaking fluid.
Oil Level
For the bus to safely operate, the level of the oil should be between the full and the add lines.
Alternator & Belt
The alternator should be securely mounted and the wires should be securely fastened. The belt should not be cracked or frayed. There should be no loose fibers or signs of wear and the belt should not give more than 3⁄4 of an inch.
Water Pump
The water pump should be securely mounted and not leaking. I am inspecting the belt.
Air Compressor
The air compressor should be securely mounted and not leaking. The air compressor is gear driven, so there is no air compressor belt.
Exhaust System
The exhaust system should be mounted securely and connected tightly. There should be no loose clamps. The exhaust system should not be damaged or leaking and not have any cracks, holes, or severe dents.
Fuel Tanks
I do not detect/smell any CNG leaking. The fuel cap should be tight, the fuel door and tanks (above the bus) should be secure.
Battery Compartment
The batteries are not visible or accessible. I’ll be turning on the battery switch. The door is not damaged and opens/closes securely.
Clip Lights and Hazards
The lights are clean, not missing or broken, and functioning properly. The lights are amber in the front and red in the rear except for the hazards which are amber.
Low Beams & High Beams
I’m inspecting the low beams and high beams.
Reflectors (4)
I’m inspecting the reflectors.
Turn Signals
The left and right turn signals are functioning properly as you indicated.
Mirrors
Both of the mirrors are securely mounted, not damaged, and clean.
Windshield
The windshield is clear and there are no obstructions or damage to the glass.
Windshield Wipers
The wiper arms and blades are secure and not damaged.
Running Lights
I’m inspecting the Running Lights.
Front Door Lights
I’m inspecting the Front Door Lights.
Kneeler & Wheelchair Ramp Light
I’m inspecting the Kneeler & Wheelchair Ramp Light.
Hazard Lights
I’m inspecting the Hazard Lights.
Reflectors
I’m inspecting the Reflectors.
Rear Door Lights
I’m inspecting the Rear Door Lights.
Rear Kneeler & Wheelchair Ramp Light
I’m inspecting the Rear Kneeler & Wheelchair Ramp Light.
Clip Lights
I’m inspecting the Clip Lights.
Tail Lights
I’m inspecting the Tail Lights.
Hazard Lights
I’m inspecting the Hazard Lights.
Reflectors
I’m inspecting the Reflectors.
Brake Light and Turn Signals
Can you give me a thumbs up when the brake light and turn signals come on? The brake light and the turn signals are functioning properly as you indicated.
Front Door
The door should not be damaged and secure to the hinges.
Front Door Windows
The windows are clean and not damaged.
Weather Stripping
The weather stripping in the middle of the doors should be intact.
Wheel Skirt
The wheel skirt is securely attached and not damaged.
Mud Flap
The mud flap is securely attached, not damaged, and not dragging on the ground.
Tread Depth
The tread depth on the front tire must be at least 4/32 of an inch. The tread should also be worn evenly.
Sidewall
The sidewall of the tire should not be cut/damaged or bulging.
Rim
The rim is not bent or damaged. There are no welding repairs or rust.
Lug Nuts
The lug nuts are present, not loose or cracked, and free from rust.
Hub Oil Seal
The hub seal is not leaking any oil.
Air Stem Valve & Cap
The air stem valve and cap are not missing, broken, or damaged.
Inflation
Inflation can only be properly checked with a tire gauge.
Front Suspension
Although not visible, the Front Suspension, Brakes, Steering, and Linkages are all located behind the tire. I will now explain the criteria I would use to inspect all of these items.
Shocks
The shock absorbers are secure and not leaking.
Air Bags
The air bag is mounted securely, not leaking or damaged.
Air Mounts
The air bag mounts are secure and not damaged.
U-bolts
The bolts on the suspension are secure and not damaged.
Brake Hoses
Brake hoses should supply air to the brakes. Hoses are not cracked, worn, or frayed. All couplings and fittings are secure and not leaking.
Brake Chamber
The brake chamber is not leaking, cracked, or dented. It is mounted securely and there are no loose or missing clamps.
Slack Adjustor & Pushrod
The slack adjustor should be securely mounted and have no bent, broken, loose, or missing parts. When the brakes are released and pulled by hand, the pushrod should not move more than 1 inch.
Brake Drum
The brake drum has no cracks or holes or any loose or missing bolts. The brake linings should not be worn dangerously thin. The drum and linings have no grease or oil on them.
Steering Box
The steering box should be securely mounted, not leaking, and have no missing nuts, bolts, or cotter pins. There should be no power steering fluid leaks or damage to the hoses.
Linkages
Links, arms, and rods from the steering box to the wheel are not worn or cracked. The joints and sockets are not worn or loose. There should be no loose or missing nuts, bolts, or cotter pins.
Rear Door
I am inspecting the rear door.
Rear Wheel Skirt
I am inspecting the Wheel Skirt.
Rear Mud Flap
I am inspecting the Mud Flap.
Rear Tread Depth
The tread depth on both rear tires is at least 2/32 of an inch. The tread should be worn evenly.
Spacing
There should be no foreign objects between the two tires and the tires should be spaced evenly.
Rear Sidewall
I am inspecting the Sidewall.
Rear Rim
I am inspecting the Rim.
Rear Lug Nuts
I am inspecting the lug nuts.
Rear Axle Seal
I am inspecting the axle seal.
Rear Air Stem Valves & Caps
These are two air stem valves and caps, and I am inspecting them.
Rear Inflation
The inflation can be properly inspected with a tire pressure gauge.
Rear Air Bags/Shocks/U-bolts
I am inspecting the air bags, shock absorbers and bolts on the suspension.
Rear Air Mounts & Torque Arms
There are no missing or damaged bushings. The torque arms are mounted securely and not damaged. There are also air bag mounts that I would inspect.
Rear Brakes
The rear brakes are also located behind the rear tires. They are identical to the front brakes and I would inspect them the same. The brake components include Brakes Hoses/Lines, Brake Chamber, Slack Adjustor & Pushrod, and Brake Drum.
Drive Shaft
The drive shaft should not be bent, twisted, or cracked. The U-joints should be free of foreign objects and secure.
Frame
There should be no cracks or bends on the longitudinal frame members. There should be no loose, cracked, bent, broken, or missing cross members.
Front Passenger Entryway
The step should be clear of obstructions and the tread on the stairs should not be excessively loose or worn. The handrails should be secure to the bus. The step lights and both passenger mirrors are in good condition.
Driver and Passenger Seats
There are no broken seat frames and the seats are firmly attached to the floor. All of the seat cushions are securely attached to the seat frames.
Emergency Exit Windows
Every window with a red handle is an emergency exit. To open, pull on the red handle while pushing out on the window. It is not damaged, operates smoothly, and closes securely.
Emergency Exit Roof Hatches
There are two emergency roof hatches, one in the front and one in the rear. To use the roof hatch, turn the knob and push the hatch out.
Rear Passenger Entryway
I am inspecting the rear passenger entryway.
Emergency Triangles
There are three emergency triangles with red reflectors on them.
Fire Extinguisher
The extinguisher is secured and the arrow is in the green therefore it is properly charged.
Circuit Breakers
This bus does not have spare fuses because it runs on circuit breakers, and they are located in the panel under the driver’s window.
Safe Start
The bus started in neutral with the parking brake engaged.
Heater
The heater came on.
Door Controls
The front and rear doors both open and close when switched to the correct positions.
Hazard Lights
The hazard indicator lights are working properly.
Turn Signals
Both turn signals are working properly.
High Beams
The high beam indicator light is working properly.
Defroster
The defrosters are blowing warm air.
Windshield Wiper
The windshield wipers and washer are functioning properly.
Air Pressure
The air gauge is working properly and the air compressor builds air until it cuts out at no higher than 140 psi.
Voltmeter
The voltmeter charge light on the dash has gone off and is within normal operating levels between 24-28 volts, showing that the alternator is charging.
Oil Pressure
The oil pressure warning light is not on and is within normal operating levels between 25-50 psi.
Water/Coolant Temperature
The temperature light on the dash is not on and is within normal operating levels of no higher than 220 degrees.
Wheelchair Ramp
To use the wheelchair ramp, I will open both doors & ensure my hazards are on. I will kneel the bus, then deploy and stow the ramp. The ramp stows properly and there is no damage.
Horn
The horn is functioning properly.
Interior & Exterior Mirrors
The interior and exterior mirrors are properly adjusted.
Governor Cut In
For the governor cut in test, I will make sure the needles are not rising. I will press and release the service brake then wait 20-30 seconds for the governor to cut in. I will know the governor cuts in when the arrows start rising. It should cut in by 85 psi to pass the test. If it does not cut in, I will repeat the procedure. The governor cut in at _ psi which is by 85 psi so the test was passed.
Low Air Buzzer and Light
For the low air buzzer and light test, I will be pumping the service brake until I hear the low air buzzer come on and see the light on both gauges come on. They should come on no lower than (by) 55 psi to pass the test. The low air buzzer and light came on at _ psi which is above 55 psi so the test was passed.
Spring Brake/Pop Out Test
For the spring brake test, I will be turning off the bus and releasing the parking brake. I will pump on the service brake until the parking brake pops back out. The parking brake popped out at _ psi so the test was passed.
Governor Cut Out
For the governor cut out test I will be turning on the bus and letting the bus air itself back up. The governor needs to cut out by 140 psi. I will know that it cuts out when the arrows stop moving. The governor cut out at _ psi which is by 140 psi so the test was passed.
Applied Brake Test
For the applied test, I will turn the Fast Idle off and turn the bus off. I will release the parking brake and apply the service brake with constant pressure for one minute. The bus cannot lose any more than 3 psi. The bus lost _ psi after one minute which is less than 3 psi so the test was passed.
Static Brake Test
For the static brake test, I will let the bus sit for a minute without applying any brakes. The bus cannot lose any more than 2 psi. The bus lost _ psi after one minute which is less than 2 psi so the test was passed.
Service Brake Test
For the service brake test, I will release the parking brake, put the bus in drive, and move forward at no more than 5 mph. (Do not apply the accelerator; allow the bus to roll.) When I apply the service brake, the bus should come to a complete stop and not pull to one side or the other. When I applied the service brake, the bus came to a complete stop and did not move to one side so the test was passed.
Parking Brake Test
For the parking brake test, I will engage the parking brake, put the bus in drive, and try to move forward.. The bus should not move. The bus did not move so the test was passed.