Seams, Fasteners, Sealants, and insulation (Theory)

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/50

flashcard set

Earn XP

Description and Tags

**** Could use more notes, specifically allowances and insulation

51 Terms

1
New cards

Name two ways that sheet metal can be fastened?

Sheet metal seams are fastened by forming the sheet metal itself and by the use of fastening devices such as screws, bots or rivets.

2
New cards

what is another name for the peen seam?

The single seam

3
New cards

what is the function of the drip edge?

to divert the flow of water away from the structure it is attached to.

4
New cards

The Pittsburgh Lock can withstand higher operating pressures than the button lock?

True

5
New cards

what type of notch is cut at a 45 degree angle to prevent overlapping of edges when single hems are to meet at right angles?

A slant notch

6
New cards

What are two types of blind rivets?

open end and closed end

7
New cards

to obtain full strength of a riveted joint, a rivet of the correct ____ and ____ must be used

Length and diameter

8
New cards

Name 5 types of screw heads typically used by sheet metal workers

Slotted, Robertson, Phillips, Hex head, and combination

9
New cards

What types of anchor is a setting tool used with?

Drop-in expansion shell anchors have a cone-shaped plug inside that is driven in with a setting tool after it is dropped into a pre-drilled hole.

10
New cards

the plastic toggle anchor can be used in both hollow and solid walls, True or false?

True

11
New cards

Name four reasons for using caulking

Moisture resistance, air tightness, thermal improvement and aesthetics.

12
New cards

what is the surface area temperature range duct sealer must withstand?

-30 degrees F to 175 degrees F

13
New cards

Hot melt sealants are usually applied in the field, true or false?

False

14
New cards

Duct line adhesives can be either ____ based or _____ based?

Water or solvent

15
New cards

Name three reasons for installing metal nosing on duct liner?

1) When air reaches past 4000 ft per min a metal nosing must be served to the edge of the duct to protect the insulation.

2) Metal nosing is required when an unlined duct meets a lined duct.

3) When transverse edges are facing the air stream at fan discharge

16
New cards

what is grip range when reffering to rivets?

The total thickness of material being joined.

17
New cards

what are Rivet burrs used for?

they are used for backing when connecting soft materials like neoprene in a canvas connector.

18
New cards

if a standing drive joint has a standing part or height of ¾ what is the total allowance?

1 1/4 , ¾ plus a half in for the drive connection.

19
New cards

what is the allowance for a wired edge for 24 guage and lighter?

2 ½ times the diameter

20
New cards

what is the allowance for a female part of a pittsburgh lock?

The allowance can range from 15/16'“ to 1 3/8”

21
New cards

what is another name for a dovetail seam?

Stop Lock

22
New cards

Another name for a Standing drive joint?

CP Joint

23
New cards

sheet metal seams are fastened by forming the sheet metal itself into a seam and by the use of _______ devices

Fastening

24
New cards

The lap seam is the most _____ seam of all seams used in sheet metal

basic

25
New cards

The allowance for the lap seam is _____” width or 1W

1/2”

26
New cards

the grooved seam is used to join edges on ______ objects such as pipe and round fittings

round

27
New cards

The standing seam is used primarily because of it’s ____ and reinforcing qualities on metal over large, flat areas.

Stiffing

28
New cards

the end slip joint is an ______ shaped joint that is formed on the end or edge of a piece of material

S

29
New cards

the single seam is also known as the ______ seam

peened

30
New cards

the double seam is a single seam that is ______ over to form the double seam.

hammered

31
New cards

The elbow seam is used for joining individual sections or gores of round _____ or offsets

elbows

32
New cards

The dovetail seam is normally a ______ fabricated seam

field

33
New cards

Edges are used to add safety and improve the _____, as well as adding strength to metal fittings or projects

appearance

34
New cards

The allowance for a single hem is?

1W

35
New cards

A drip edge is used on flashing to _____ the flow of water away from the structure it is attached to.

divert

36
New cards

the Pittsburgh Lock can withstand higher operating ______ than the button lock.

pressure

37
New cards

the allowance for a hammer lock is ____ times the width

3 typically 3/4”

38
New cards

the slip and drive joint uses _____ cleat and _____ cleats to attach ductwork and fittings together.

Slip and Drive

39
New cards

The transverse duct connector, or TDC adds _____to the duct and is formed by a special roll forming machine.

Strength

40
New cards

Notching is the process of removing ____ material

excess

41
New cards

A straight notch is used when ______ or notching for a flange on an outside corner.

dovetailing

42
New cards

A slant notch is cut at what angle to prevent overlapping of edges when single hems are to meet at right angles?

45 degrees

43
New cards

blind rivets are also known as?

pop rivets

44
New cards

The total thickness of the material being joined is referred to as?

Grip range

45
New cards

Solid rivets can be made from aluminium, carbon steel, stainless steel, copper, brass and _____ metal

monel

46
New cards

Sheet metal screws form their own _____ in metal so that the fastener can be removed and pit back in if required

thread

47
New cards

The self- piercing sheet metal screw has a _____ point and requires no pre drilling of holes

sharp

48
New cards

The lag screw has a very _____ thread, with either a square or hex head

coarse

49
New cards

anchors are used when the fasteners cannot penetrate a solid material or a _____ wall

hollow

50
New cards

The plastic screw anchor is an all-purpose, ____-duty anchor that can be used in both hollow and solid walls

light

51
New cards

Duct liner adhesives can be either _____ based or solvent based

water