1/31
Looks like no tags are added yet.
How to be current to act as PIC under IFR conditions?
6 HITS
6 instrument approaches
Holding procedures and tasks
Intercepting and tracking courses
What if you’re not current within the last 6 months
You can log 6 hits with a safety pilot
Safety pilot must have at least a PPL, can see front and side of aircraft, and aircraft must have dual control system
What if you’re not current within the last year
Instrument proficiency check with a CFII, examiner, or anyone else approved
How to carry passengers as PIC
3 takeoffs and landings within the last 90 days
How can you fly in IFR conditions
91.173
No person may operate an aircraft in controlled airspace unless they’ve filed an IFR flight plan and received an appropriate ATC clearance
You can fly IFR in class G but you must remain in class G until you file and get clearance
How to file an IFR flight plan
Call the FSS
Online
Foreflight
With ATC
File at least 30 minutes before departure
How to cancel a flight plan
Towered airport - automatically cancelled by atc upon landing
Non towered - pilot must contact atc to cancel
Cancel anytime in flight out of IMC and out of class A airspace
What are the IFR minimum fuel requirements
91.167
Fuel from departure to destination airport, plus fuel from destination to most distant alternate, plus 45 minutes calculated at normal cruise
When is a destination alternate not required
91.169
An instrument approach is published and available for the destination, AND,
■ For at least 1 hour before to 1 hour after ETA:
▷ Ceiling will be at least 2000’ above airport
elevation; and
▷ Visibility will be at least 3 SM.
MINIMUM WEATHER CONDITIONS REQUIRED AT AN AIRPORT TO LIST IT AS AN ALTERNATE
The alternate airport minimums published in the
procedure charts, or, if none:
■ Precision approach:
600 ft ceiling and 2 SM visibility.
■ Non-precision approach:
800 ft ceiling and 2 SM visibility.
■ No instrument approach available at the
alternate:
Ceiling & visibility must allow descent from MEA,
approach and landing under VFR.
§91.169
What are the IFR cruising altitudes
0-179° odd thousands
180-359° even thousands
IFR takeoff minimums
Prescribed takeoff minimums for the runway, and if none
1-2 engine airplanes: 1SM visibility
More than 2 engines: ½ SM visibility
What do the departure procedures do
Ensures obstacle clearance, provided:
▷ the airplane crossed the departure end of the
runway at least 35 ft AGL,
▷ reaches 400 ft AGL before turning, and
▷ climbs at least 200 Feet per NM (FPNM), or as
published otherwise on the chart.
What are the 2 types of departure procedures
Obstacle Departure Procedure (ODP)
□ Provides only obstacle clearance.
▷ Standard Instrument Departure (SID)
■ designed to provide obstacle clearance and facilitate efficient ATC routing.
basic STAR procedure.
■ Usually named according to the fix at which the
basic procedure begins.
■ As with a SID, you can state “NO STARs” in the
remarks section of the flight plan, to avoid getting a
clearance containing a STAR.
■ RNAV STARs require RNAV 1 performance.
□ Some SIDs may depict special radio failure
procedures.
Minimum IFR altitudes
no person may operate an aircraft under
IFR below-
▷ Minimum altitudes prescribed for the flown
segment, or if none:
▷ Mountainous areas: 2,000 ft above the highest
obstacle within a horizontal distance of 4 NM
from the course.
▷ Non-mountainous areas: 1,000 ft above the
highest obstacle within 4 NM from the course.
Types of altitude
Indicated altitude – Uncorrected altitude indicated on the dial when set to local pressure setting (QNH).
■ Pressure altitude – Altitude above the standard 29.92. Hg plane. (QNE). Used when flying above the transition altitude
(18,000’ in the US)
■ Density altitude – Pressure alt. corrected for nonstandard temperature. Used for performance calculations.
■ True altitude – Actual altitude above Mean Sea Level (MSL).
■ Absolute altitude – Height above airport elevation (QFE)
VFR Day required equipment
A - Altimeter
T - Tachometer for each engine
O - Oil temperature indicator for each engine
M - Manifold pressure gauge for each altitude engine
A - Airspeed indicator
T - Temperature gauge for each liquid cooled engine
O - Oil pressure gauge for each engine
F - Fuel quantity gauge for each tank
L - Landing gear position lights (if retractable gear)
A - Anticollision lights (aircraft certified after March
11, 1996)
M - Magnetic direction indicator (mag. compass)
E - ELT, if required by §91.207
S - Safety belt / shoulder harness
VFR night required equipment
F - Fuses (spare set)
L - Landing light (if for hire)
A - Anticollision lights
P - Position lights (navigation lights)
S - Source of electrical power
IFR required equipment
VFR requirements and
G - Generator / alternator
R - Radios (two-way navigational equipment appropriate for the route
to be flown)
A -Altimeter (sensitive = adjustable for barometric pressure)
B - Ball (slip-skid indicator)
C - Clock (shows hours, minutes and seconds and installed as part of
aircraft equipment)
A -Attitude indicator
R - Rate-of-turn indicator
D - Directional gyro (heading indicator)
What’s a localizer
Provides lateral course guidance.
■ Frequencies: 108.1 - 111.95 MHz with odd tenths only.
■ Width: Between 3°-6° so that the width at the threshold would be 700 feet.
Usually 5° total width. (2.5 full deflection to each side, 4 times more sensitive
than a VOR).
■ Coverage range: 35° to each side of the centerline for the first 10NM and 10°
Back
Course
up to 18NM from the antenna and up to an altitude of 4500'.
What’s a glide slope
Provides vertical course guidance.
False Slope
■ Frequencies: 329.3 to 335 MHz (UHF) (automatically tuned with Localizer freq.)
1.4º
■ Width: 1.4º (full deflection is 0.7º either direction).
3º
10
NM
■ Range: typically up to 10 NM.
250-650 ft
■ Slope: typically 3°.
■ Errors: False glide slope above normal glide slope
What are marker beacons
Provide range information over specific points along the
M
approach. Transmits at 75 MHz.
I
■ Outer marker: 4-7 miles out. Indicate the position at which
the aircraft should intercept the GS at the appropriate interception altitude ±50ft. BLUE. “- - -“
■ Middle marker: ~3500ft from the runway. Indicates the approximate point where the GS meets the decision height. Usually
200ft above the touchdown zone elevation. AMBER. “. - . -”
■ Inner marker: between the MM and runway threshold. Indicates the point where the glide slope meets the DH on a CAT II ILS
approach. WHITE. “. . .”
■ Back course marker: Indicates the FAF on selected back course approaches. Not a part of the ILS approach. WHITE.
What’s the ALS
APPROACH LIGHT SYSTEMS
■ Provides basic visible means to transition between instrument-guided flight into a visual approach.
■ ALS extends from the landing threshold into the approach area up to:
ALSF-2
ILS
Category Visibility DH
▷ 2,400-3,000 feet for precision instrument runways, and
▷ 1,400-1,500 feet for non-precision instrument runways.
■ May include sequenced flashing lights, which appear to the pilot as a ball of light traveling
towards the runway at twice a second (AKA “The Rabbit”).
■ The visible parts of the ALS configuration can help the pilot estimate flight visibility.
Mandatory reports under IFR
■ Missed approach
■ Airspeed ±10 kts / 5% change of filed TAS (whichever Is greater)
■ Reaching a holding fix (report time & altitude)
■ VFR on top when an altitude change will be made.
■ ETA change ±3 min
■ Leaving a holding fix/point
■ Outer marker (or fix used in lieu of it) *
■ Un-forecasted weather
■ Safety of flight (any other information related to safety
of flight)
■ Vacating an altitude/FL
■ Final Approach fix
■ Radio/Nav/approach equipment failure (§91.187)
■ Compulsory reporting points ▲ * (§91.183)
■ 500 - unable climb/descent 500 fpm
* Required only in non-radar environments (including
ATC radar failure)
Position reports required in non radar environment
■ Aircraft ID
■ Position.
■ Time.
■ Altitude.
■ Type of flight plan (except when communicating with
ARTCC / Approach control).
■ ETA and name of next reporting fix.
■ Name only of the next succeeding point along the
route of flight.
■ Any pertinent remarks.
Lost comms procedure
Altitude to fly - FLY THE HIGHEST OF:
M.E.A–
■ M - Minimum altitude prescribed for IFR
■ E - Expected (as in: “Expect 5000 10 min after departure”)
■ A - Assigned. Last altitude assigned by ATC
Route to fly - SELECT THE ROUTE BY THIS ORDER:
A.V.E.F–
■ A - Assigned route, if none:
■ V - Vectored (fly to fix/route/airway last vectored to), if none:
■ E - Last Expected route by ATC, if none:
■ F - Filed route
When can you descend below DA/MDA
1. The aircraft is continuously in a position from which a descent to a landing on the intended runway can be made at a normal rate of descent using normal maneuvers.
2. The flight visibility (or the enhanced flight visibility, if equipped) is not less than the visibility prescribed in the standard instrument approach being used.
3. At least one of the following visual references for the intended runway is distinctly visible and identifiable to the pilot: (except for CAT II & III approaches)
i. The approach light system, except that the pilot may not descend below 100 feet above the touchdown zone elevation using the approach lights as a reference unless the red terminating bars or the red side row bars are also distinctly visible and identifiable.
ii. The threshold.
iii. The threshold markings.
iv. The threshold lights.
v. The runway end identifier lights.
vi. The visual glideslope indicator.
vii. The touchdown zone or touchdown zone markings.
viii. The touchdown zone lights.
ix. The runway or runway markings.
x. The runway lights.
What malfunctions must be reported?
Navigation equipment failures
Approach equipment failures
Communication equipment failures
If you only see the approach lights at DA, how low can you descend?
You can descend to 100 feet above touchdown zone elevation, provided the other requirements of 91.175(c) are satisfied.
To descend lower, you must see the red terminating bars or red side-row bars, or another qualifying runway reference.
What does the lightning bolt symbol on an approach plate represent?
It identifies the glideslope intercept altitude at the published fix on an ILS approach.
What happens if you lose sight of the runway while circling?
Execute the published missed approach. Make an initial climbing turn toward the landing runway, then follow the published missed approach unless ATC directs otherwise.
What is the standard leg timing for holds
At or below 14,000 feet MSL: 1-minute inbound legs.
Above 14,000 feet MSL: 1.5-minute inbound legs.