1/25
Looks like no tags are added yet.
What safety precautions should be taken during titrations?
Wear eye protection and gloves, rinse equipment properly, and treat unknown substances as potentially toxic.
What range should each repeat titre result be in of eachother in order for the results to be included to calculate the mean titre?
IDEALLY WITHIN 0.1CM OF EACH OTHER

TITRATION steps
Rinse the burette with acid
Rinse the pipette with alkali so titration is done with a known concentration of (alkali)
Use a pipette to measure alkali into a conical flask.
Add a few drops of indicator.
Fill the burette with the acid and record the starting reading.
Add the acid from the burette to the flask while swirling.
Near the end point, add the acid drop by drop.
Stop when the indicator changes colour
Record the final burette reading.
Repeat until you get at least 2 concordant results
What is the endpoint color change when using phenolphthalein as an indicator?
Pink (alkali) to colorless (acid).
What is the endpoint color change when using methyl orange as an indicator?
Yellow (alkali) to red (acid).
What happens if the jet space in the burette is not filled properly before a titration?
It can lead to errors in the titre reading.
What is the purpose of using a white tile under the flask during titration?
To help observe the color change
How should acid be added to alkali during a titration?
Add acid dropwise at the end point while swirling the mixture.
What is the significance of obtaining concordant results in titration?
Concordant results are two readings within 0.1 cm³ of each other, indicating accuracy and consistency
Why is a conical flask preferred over a beaker for titration?
It is easier to swirl the mixture without spilling.
What should be done if too much indicator is added during titration?
It can affect the titration result; only a few drops should be added
How should results from a titration be recorded?
Results should be recorded in a table, including both initial and final readings, and titre volumes to 2 decimal places.
What is the role of distilled water during titration?
It washes the sides of the flask to ensure all acid reacts with the alkali.
What is the purpose of quality control in titration?
To ensure the concentration of the chemical being tested is consistent across samples.
What substances are good for neutralizing excess acid?
Sodium hydrogen carbonate (NaHCO3) and calcium carbonate (CaCO3).
What is the significance of using a volumetric flask in titration?
It ensures accurate dilution of solutions.
first 2/3 steps of back titrations
1) Reacting sample w/ an excess of acid/base (known concentration)
2) Titrating- a) resulting product b) excess acid/base (reactant)
3 reason for use of back titration
used for insoluble base/acid
volatile reactants
too slow reactants
What is the final step in a back titration calculation?
Calculate the concentration of the original substance in g/dm³.
What is the process for making a solution from a solid?
Weigh the solid, dissolve in water, and make up to the mark in a volumetric flask.
What happens when soluble ionic solids dissolve in water? Why does this matter?
They dissociate into separate ions. SO the ion concentrations CAN differ to solute’s concentrations, i.e;
MgCl2(s) +aq → Mg2+(aq) + 2Cl-(aq)
0.1 mol 0.1 mol 0.2 mol
IF substance doesnt dissolve well in beaker
the beaker and its contents could be heated gently until all the solid had dissolved
What is the dilution process of a solution using a volumetric pipette?
Pipette a specific volume of the original solution and dilute with distilled water.
What safety precautions should be taken when handling hazardous substances?
Wear goggles, gloves, and avoid skin contact
Diluting a solution effect on moles, concentration and volume:
will not change the amount of moles of solute present increase the volume of solution
the concentration will lower
What is the significance of the meniscus in volumetric measurements?
The bottom of the meniscus should sit on the line for accurate measurement.