1/68
Looks like no tags are added yet.
What is quality control
Comparing output to standards and correcting unacceptable resuts
What are the 3 phases of QA
Acceptance Sampling → Process Control → Continuous Improvement
What is the optimal amount of inspection
The inspection level that minimizes total inspection and defect costs
Attributes vs Variables
Attributes are counted/classified; Variables are measured
When is centralized inspection preferred
Wehn specialzed equipment or labratory conditions are needed
When should inspection happen before a covering process
Before work hides defects, such as checking plumbing before dry wall
Why is inspection alone insifficent for QC
It detects but doesn’t neccessarily prevent them. Process control help prevent defects
What is acceptace Sampling
Inspecting a sample from a batch to decide whether the batch is acceptable
Process control
Monitoring and correcting a process during production to maintaon quality
Continuous improvement
Continously improving processed to build quality into prodction and prevent defects
Which QA assurance phase is most progressivr
Continuous Improvement bc quality is built into the process
Does increasing inspection always reduce total cost?
No. Inspection costs rise while the cost of passing defects falls. Total cost is minimized at the optimal inpection level
What are the 4 main inspection decisions
How much/how often
Where in process
centralized vs onsite
attributes vs variables
Why inspect before a costly or irreverable operation
To catch defected before they cause expenive waste or become impossible to correct
What is the main advantage of on-site inspection
Faster decisions, less disruption, and QA at the source
What is the main trade-off between centralized and on-site inspection
Centralized offers specialized testing ; onsite offers faster feedback and less dsruption
Statistical Process Control ( SPC)
Statistical evalualtion of process output to determine whether a process is in control
Quality of confomance
The extent to which a product or service meets it’s specification
Main question of process control
Is the process stable, with only random variation?
Main question of process capability
Can a stable process consistently meet specifications
Can a process be stable but not capable
Yes. It may operate conistently while producting output outside it’s specifications
Why should process control be assesed before capability
Capability assumes the process is stable; unstable process is not predictable
What is random ( common cause) variation?
Natural Variation caused by numerous minor factors
What is assignable ( special cause variation)
Nonrandom variation with an identfifiable cause
Does every variation require corrective action
No. Normal random variation is expected; Special causes require investigation
Purpose of Sampling in SPC
To periodically collect data and evaluate whether process variation is random
What are the 6 steps of the control processes
Define
Measure
Compare
Evaluate
Correct
Monitor
Ask chat the change the cheatsheet and then make the cheatsheet + finish this chapter today
Control chart
A time-ordered plot of sample statistics used to distinguish random from nonrandom variation
What fo UCL and LCL represent
Upper and loqer control limits defining the expected range of process variation
What does the centre line ( CL) represent
The process average or epected value of the plotted statistic
What does a point outside the control limits indicate
An out-of-control signal suggesting assignable variation that needs investigation
Does a point inside control limits guarentee the process is in control
No. Random patterns may exist even when all points are inside the limits
Can a process be in control but produce defective products?
Yes. It may be stable but unable to meet specifications
Type I error
False Alarm: Concluding a process is out of control when it is actually in control
Type II error
Missed Alarm: Concluding a process is in control when it is actually out of control
Which error is manufacturer’s risk?
Type I bc it can cause unncecessary investigatio or correction
Which error is consumer’s risk
Type II bc a real process problem goes undected
What is a (alpha) for three-sigma control limits under normality
Approx. 0.27%, with 0.135% in each tail
What are control Charts for variables used for?
Monitoring measurable characteristics, such as length, weight, or temperature
What does an X-bar chart monitor?
The central tendency (mean) of a process
What does an R-chart monitor?
Process dispersion ( variability or spread)
If the process average shifts, which chart is most useful
X-bar chart
If the process mean stays constant but variability increases, which chart is most useful?
R Chart
How to calculate a sample range
Maximum observation - Minimum observation
Grand Mean
The average of all sample means
Average range
The average of all sample ranges
A factory takes 25 samples of 4 items each. Which n is used for the constants?
n = 4, not 25
Why shoulf X-bar and R charts be used together?
They monitor different things: the process mean and it’s variabilty
Can X-bar chart appear in control while the R-chart is out of control
Yes. The mean can be stable while variability is excessive
How many samples does the prof reccomend for intial controls
20-25 samples
What should you do if preliminary control limits reveal an out-of-control signal?
Investigate and correct assignable causes, then collect new observations and reassess
What is the difference between p-charts and c-charts?
P-chatr monitors proportion of defective items; c-chart monitors the number of defects per unit
A product has five scratches. How would p-chart and c-chart treat it?
P-chart: 1 defective item
C-chart: 5 defects
What happens when a calculated control-chart LCL is negative?
Set it to zero because negative defect counts or proportions are impossible
What is an important requirement for using a c-chart?
The inspection unit or opportunity for defects must retain constant
What is a run test
A test for nonrandom patterns like a sequence of observations
What is the difference between a trend and cycle
Trend = sustained movement in one direction. Cycle = repreating wave-like movement
What does bias mean on a control chart?
Too many observations occur on one side of the centre line
Can a process be out of control even if all observations fall within control limits?
Yes. Nonrandom patterns can indicate an unstable process
What is process capability
How well a stable process’s natural variation fits within the specification limits
What is the difference between Cp and Cpk
Cp measured potential cabailty based on spead; Cpk also accounts for centering
How do you interpret Cp <1 , =1, >1
<1 : Process wider than specs
=1 : Equal widths
>1 : Process narrower than specs
Can Cp be high while Cpk is low
Yes. The process may have lower variabilty but be off-centre
Can Cpk ever be greater than Cp
No. Cpk ≤ Cp. They are equal when is the process is centered.
5 ways to improve process capability
Simplify, Standardize, Mistake-proof, Upgrade equipment, automate
What do the X and Y axes of an OC curve represent
X= Actual proportion defective; Y = probability of accepting the lot
What happens to acceptance probability as the defect rate increases
It decreases
What happens if the acceptance number c increases while n stays fixed
The sampling plan becomes more lenient, so acceptance probability increases