1/39
Practice vocabulary flashcards covering air properties, ventilation standards, duct fabrication, fittings, dampers, duct sizing, fans, and air curtains from Chapter 30 and Section 9 Indoor Air Fundamentals.
Latent Heat
The heat or energy stored within moisture in the air.
Air Stratification
The thermal layering of air in a conditioned space, which is prevented by an air distribution system keeping the air moving.
Primary Air
Air delivered directly to a room from a supply duct.
Throw
The distance that air entering a room travels from the duct outlet before it slows to 50fpm.
Negative Pressure
The pressure condition produced in a room when more air is leaving than entering, which increases infiltration around windows and doors.
Minimum Cooling Ventilation Rate
The ventilation standard requiring an air-conditioning system in cooling mode to supply at least 15cfm of outdoor air per person.
Air Exchange Rate
The rate at which volume of indoor air is replaced per hour, calculated as 1.8 air exchanges per hour for 10 people in a 5000ft3 space requiring 15cfm per person.
Natural Convection
The thermal circulation mechanism utilized in vented attics by placing upper vents and lower vents to allow warm, rising air to exit.
Soffit Vents
Intake vents located at the lower eaves of an attic through which outside air enters, rather than an exhaust opening for rising hot air.
Whole House Fan
A home cooling ventilation fan operated only after opening windows and confirming that outdoor temperature is lower than indoor temperature.
Insulated Ducts
Ductwork installed in unconditioned spaces, such as attics or crawl spaces, specifically treated to reduce heat loss.
Return Air Plenum
An air collection compartment frequently created within the open space between a false ceiling and the real structural ceiling.
Fabric Joint
A flexible duct connection installed to absorb and account for the thermal expansion and contraction of sheet metal ductwork.
Starting Collar
A sheet metal fitting used to connect a round duct run directly to a plenum.
Crimped End
The tapered end of a round duct section that must always be oriented facing toward the direction of airflow.
Duct Tape
An adhesive tape that should never be used to seal ductwork joints.
Aspect Ratio
The dimensional ratio of a rectangular duct's wide side to its narrow side.
Elbow
A duct fitting that provides a directional turn in a duct run, usually 90∘.
Butterfly Damper
A single-blade circular damper used inside round ducts to regulate or balance airflow.
Diffuser
A supply air terminal device that spreads air leaving a duct uniformly across a room, distributing air more evenly than a register.
Grille
A nonadjustable louvered fixture used to cover a return duct inlet.
Multiple-Blade Damper
A damper assembly primarily used in square or rectangular ducts to restrict or completely shut off airflow.
Register
A supply terminal device that delivers air into a room using one or more adjustable airstreams.
Split Damper
An adjustable damper installed at a junction where an airstream branches off in two directions.
Variable Air Volume (VAV) Controller
A controller required in an HVAC system that regulates the volume of conditioned air delivered to zones by modulating dampers.
Vertical Fire Damper
An automatic fire damper required in all vertical ducts that pass through a fire-rated ceiling or floor in commercial and industrial buildings.
Dynamic Fire Damper
A type of fire damper certified and required at locations where the HVAC fan pressure will remain active during a fire.
Class A Fire Damper
The rating classification for a fire damper designed to hold back a fire indefinitely.
Fusible Link
A temperature-sensitive metal link that holds a fire damper open during normal conditions and melts at high temperatures to close the damper.
External Static Pressure (ESP)
The static pressure difference measured directly between the blower inlet and the blower outlet.
Available Static Pressure (ASP)
The amount of friction or resistance pressure allocated to design the longest duct run in an HVAC system.
Device Pressure Loss (DPL)
The pressure drop caused by in-duct air-handling accessories such as air filters, dampers, and evaporator coils.
Effective Length
The total design length of a duct run calculated by adding the physical length of ductwork to the equivalent effective lengths of all fittings.
Friction Loss
The static pressure drop resulting from moving air rubbing against the inside surface of a duct, typically expressed in inches of water column per 100′ of duct.
Manual D
The Air Conditioning Contractors of America (ACCA) manual developed for designing and sizing both supply and return ducts in buildings.
Induced Draft
The incoming air stream drawn into the inlet side of a fan, which operates under negative pressure.
Forced Draft
The discharged air stream pushed out from the exhaust side of a fan, which operates under positive pressure.
Radial Flow
The discharge flow pattern in a fan where air exits outward at right angles (90∘) relative to the fan axle.
Air Curtain
A downward air stream device installed over an entrance with the purpose of reducing heat gain and heat loss by barring outdoor air infiltration.
Air Stagnation
An indoor air condition characterized by still, uncirculated air where air velocity drops to 15fpm or less.