1/103
Looks like no tags are added yet.
What is selective hydrogenation?
Converting unwanted unsaturated compounds into valuable products while preserving desired olefins.
What is the main objective of selective hydrogenation?
Remove impurities while minimising the loss of valuable olefins.
What are the valuable products from the C2 cut?
Ethylene.
What unwanted compound is present in the C2 cut?
Acetylene.
What are the valuable products from the C3 cut?
Propylene.
What are the unwanted compounds in the C3 cut?
Methyl-acetylene and propadiene (MAPD).
What valuable products are obtained from the C4 cut?
Butadiene, butene-1 and butenes-2.
What unwanted compounds are found in the C4 cut?
Vinyl-acetylene, ethyl-acetylene and excess butadiene.
What unwanted compounds are found in pygas?
Diolefins, alkenylaromatics and olefins.
Why is selective hydrogenation often preferred to extraction?
It is cheaper and converts unwanted compounds into valuable products.
What does a catalyst do?
Increases reaction rate by lowering activation energy.
Is a catalyst consumed during a reaction?
No. It is not consumed, but it can become deactivated.
What is the Arrhenius equation?
k = k₀e^(-Ea/RT).
What are the two ways to increase reaction rate?
Increase temperature or decrease activation energy using a catalyst.
What type of process is catalytic hydrogenation?
Heterogeneous catalytic process.
Is catalytic hydrogenation exothermic or endothermic?
Exothermic.
What are the four stages of catalytic hydrogenation?
Diffusion, adsorption, surface reaction and desorption.
What are the three key catalyst properties?
Activity, selectivity and stability.
What is catalyst activity?
The ability of a catalyst to promote reaction rate.
What is catalyst selectivity?
The ability to favour desired reactions over undesired reactions.
What is catalyst stability?
The ability to maintain performance over time.
What is the adsorption strength order?
Alkynes > Diolefins > Olefins > Alkanes.
Why does acetylene react preferentially over ethylene?
Acetylene adsorbs faster and more strongly on the catalyst.
How can catalyst selectivity be improved?
Promoters such as nitrogen compounds or silver reduce olefin adsorption.
Which metals are preferred for C2, C3 and C4 hydrogenation?
Palladium-based catalysts.
Which metals may be used for C5+ hydrogenation?
Palladium or nickel, depending on product specifications and feed impurities.
Why is nickel attractive compared with palladium?
It has a much lower catalyst cost.
What is the typical palladium particle size?
Less than 10 nm.
What is the typical nickel particle size?
Approximately 100–200 nm.
What is catalyst dispersion?
The proportion of total metal atoms exposed at the catalyst surface.
How is catalyst dispersion calculated?
100 × surface metal atoms / total metal atoms.
What is the preferred support for selective hydrogenation catalysts?
High-purity alumina.
Why is alumina used as a catalyst support?
It promotes metal dispersion, is chemically inert and mechanically resistant.
What are the main catalyst manufacturing steps?
Support beads, impregnation, drying, calcination, delivery, reactor loading and activation.
What is the typical palladium content in the catalyst?
Approximately 0.3 wt%.
What is the typical nickel content in the catalyst?
Approximately 15 wt%.
Why is heat removal important in selective hydrogenation?
The reactions are highly exothermic and can create hot spots.
What are the two reactor technology types discussed?
Adiabatic chamber and isothermal multitubular reactors.
What is the predominant hydrogenation technology?
Mixed vapour/liquid phase, co-current flow and fixed catalyst bed.
What is an advantage of liquid-phase technology?
Liquid vaporisation limits the exotherm and continuous washing helps extend catalyst cycles.
What happens when hydrogen is in excess locally?
Overreaction, reduced selectivity and hot spots can occur.
What happens when there is insufficient hydrogen?
Incomplete reaction and low conversion occur.
How can uniform gas/liquid distribution be achieved?
Optimise flowrates, flow direction, temperature, pressure, distributors and catalyst loading.
What is the purpose of reactor distributors?
Ensure uniform gas/liquid distribution at the catalyst-bed inlet.
What is catalyst channeling?
Uneven flow through the catalyst bed, reducing effective catalyst utilisation.
What is the mounding effect during sock loading?
Smaller particles concentrate near the mound axis while larger particles roll towards the outer edge.
What is the advantage of CATAPAC dense loading?
Improves bed homogeneity, prevents bypassing and sustains performance and selectivity.
What is the purpose of grading materials?
Trap particulates and contaminants, mitigate pressure-drop build-up and extend catalyst cycle length.
What is the desired C2 hydrogenation reaction?
Acetylene + H₂ → Ethylene.
What is an undesired C2 reaction?
Ethylene + H₂ → Ethane.
What is another undesired C2 reaction?
Acetylene oligomerisation, which forms green oils.
What does DeC1-first mean?
Demethanizer-first fractionation configuration.
What does DeC3-first mean?
Depropanizer-first fractionation configuration.
What is the C2 feed in the back-end configuration?
The C2 cut.
How is hydrogen injection controlled in the C2 back-end configuration?
According to the acetylene concentration and H₂/acetylene molar ratio.
What is the typical run length of the C2 back-end configuration?
Approximately 6–18 months.
What characterises the C2 front-end DeC3-first configuration?
Significant hydrogen excess, low oligomer formation and sensitivity to CO variations.
What is the typical run length of the C2 front-end configuration?
Approximately 5 years.
What is the role of CO in C2 selective hydrogenation?
It improves selectivity but lowers catalyst activity.
What is the role of MAPD in C2 front-end operation?
It acts as an activity moderator.
What does MAPD stand for?
Methyl-acetylene and propadiene.
What are the desired reactions in C3 MAPD hydrogenation?
Methyl-acetylene and propadiene are hydrogenated to propylene.
What is an undesired reaction in C3 hydrogenation?
Propylene + H₂ → Propane.
What is another undesired C3 reaction?
Methyl-acetylene hydrogenation to C6H12 dimer.
What is the difference between one-stage and two-stage C3 hydrogenation?
One-stage targets polymer-grade propylene; two-stage targets chemical-grade propylene.
Why is liquid-phase technology used in C3 hydrogenation?
It allows continuous washing to remove gums and extend catalyst cycle length.
What is pyrolysis?
Thermal decomposition without oxygen.
What is the typical pygas boiling range?
Approximately 50–200°C.
What is the purpose of GHU-1?
Stabilise unstable diolefins and alkenylaromatics while preserving aromatics.
What is the purpose of GHU-2?
Remove sulphur and remaining olefins while minimising aromatic hydrogenation.
What is the desired reaction of diolefins in GHU-1?
Diolefins are hydrogenated to olefins.
What happens to alkenyl aromatics in GHU-1?
They are hydrogenated to alkyl aromatics.
What is the desired reaction of indenics in GHU-1?
They are hydrogenated to indanes.
What is the operating temperature range of GHU-1?
Approximately 50–180°C.
What is the operating pressure range of GHU-1?
Approximately 25–30 barg.
What is the operating phase of GHU-1?
Liquid phase.
What are the benefits of palladium in GHU-1?
High activity and stability, lower oligomer formation and better regenerability.
What is an advantage of nickel in pygas hydrogenation?
Greater tolerance to contaminants and lower catalyst filling cost.
What are the main objectives of GHU-2?
Hydrodesulphurisation and hydrogenation of olefins and alkenyl aromatics.
What undesired reaction must be minimised in GHU-2?
Aromatic hydrogenation.
Which catalyst systems are used in GHU-2?
Nickel-molybdenum (NiMo) and cobalt-molybdenum (CoMo).
What is the operating phase of GHU-2?
Vapour phase.
What is the typical operating pressure of GHU-2?
Approximately 25–30 barg.
What is the GHU-2 sulphur specification?
Less than 1 ppm wt.
What is the GHU-2 bromine index specification?
Less than 100 mg/100 g.
What is the target aromatic recovery in pygas processing?
More than 99.5%.
What indicates the end of a catalyst cycle?
Off-spec product due to activity loss or increasing pressure drop.
What is catalyst regeneration?
Treatment to restore catalyst performance after deactivation.
What is catalyst end of life?
When regeneration intervals become too short or regeneration no longer restores performance.
What is a catalyst inhibitor?
A substance that reduces catalyst performance.
What is a temporary catalyst poison?
A poison whose effect can be reversed by treatment.
What is a permanent catalyst poison?
A contaminant that causes irreversible catalyst deactivation.
What is the effect of free water on catalyst activity?
It can severely reduce or kill catalyst activity.
What is the maximum free-water tolerance stated for Pd C3 and GHU-1?
Nil.
At what temperature can water-damaged catalyst be recovered using hydrogen treatment?
Approximately 150°C.
What are the main sources of sulphur contamination?
Feedstock and furnace sulphur injection.
How does H₂S affect palladium at 100°C?
It acts as an inhibitor.
How does H₂S affect palladium at 40°C?
It poisons palladium through PdS formation.
How does H₂S affect nickel catalysts?
It acts as a poison.
What is arsenic's effect on catalysts?
It is a temporary poison, particularly relevant to FCC-derived feeds.