1/13
Looks like no tags are added yet.
Multiple forces for distortion
Stretching, bending, or compressing a stationary object requires more than one force. If only one unbalanced force acts on the object, it will simply accelerate or move in the direction of the force rather than changing shape.
Difference between elastic and inelastic distortion
Elastic: when an object returns back to its original shape when the stretching or compressing force is removed
Inelastic: occurs when an object does not return to its original shape and length after the forces are removed, causing permanent deformation
Formulae
Hooke’s law: F= kx (gradient of graph)
Work done in stretching a spring: E= kx²/2 (area under graph)
Equation for density: P=F/A
Pressure in a column of liquid: P= Δhρg
F is force(N)
E is work done(J)
k is spring constant(N/m)
x is extension (length of distorted spring - original length of spring, cm)
P is pressure(Pa, N/m²)
ρ is density(kg/m³)
A is area(bh,m²)
h is height(m)
g is gravitational field strength (N/kg)
Difference between linear and non-linear relationships between force and extension
Linear relationship: Force and extension are directly proportional, producing a straight line passing through the origin on a force-extension graph
Non-linear relationships: Force and extension are not directly proportional producing a curved line on a force-extension graph
Practical: investigate the extension and work done when applying forces to a spring method
Measure original length of spring using a ruler
Add a known mass of 100g and wait until the spring stops vibrating. Record new length
Calculate extension by subtracting new length by original length
Repeat steps 2-3 when adding successive masses until 500g
Remove the masses one by one and remeasure the spring, checking that the spring returns to its original length confirming it has stayed within its elastic limit
Repeat steps1-5 4 more times then find a mean for each weight
Plot a graph with force on the y axis and extension on the x axis
Find spring constant by gradient and work done by area under graph
Spring practical reducing errors
Avoid parallax error by reading ruler at eye level. Take repeats to identify anomalies and find a mean. Use a set square to ensure that the ruler is completely parallel to the spring.
Why does atmospheric pressure vary with altitude?
Air becomes less dense as altitude increases. Atmospheric pressure is a result of air molecules colliding with a surface, so a s height increases fewer air molecules are above a surface, resulting in fewer collisions and lower atmospheric pressure.
Fluid
A substance that is either a liquid or a gas
Pressure in a fluid
The total pressure experienced by an object submerged in a liquid is the sum of the pressure due to the liquid + the atmospheric pressure pushing down on the surface of the liquid
The pressure in a fluid causes a force that acts normal (perpendicular) to any surface in contact with the fluid
Pressure relation with force and area
Pressure is the concentration of a force over a given area.
A larger area speads the force out, resulting in lower pressure e.g. to prevent sinking into softer ground
A small area concentrates the force resulting in high pressure e.g. a sharp knife easily piercing surfaces
Pressure relation to depth and density
Pressure in a fluid increases as the depth increases and increases as the density of the fluid increases.
This is because as you go deeper in a liquid, there is a greater weight of liquid above you pushing down, which increases the pressure.
Also, a denser liquid has more mass per unit volume so the same depth liquid has a greater weight pushing down, causing higher pressure.
Cause of upthrust
When a object is partially or fully submerged in fluid, the bottom of the object is deeper than the top. Because fluid pressure increases with depth, the upwards pressure on the bottom surface is greater than the downward pressure on the top of the surface. This creates the resultant upwards force capled upthrust e.g. a baloon floating on water or a helium baloon rising in the air
What is upthrust equal to?
The weight of fluid displaced
How upthrust, weight, and density effect whether an object floats or sinks
Floating: if an object’s density is less than tje density of the fluid, it displaces a volume of fluid equal to its own weight before being fully submerged. Upthrust=weight so it floats.
Sinking: if an object’s density is greater than the density of the fluid, even when fully submerged it cannot displace a weight of fluid equal to its own weight. Weight>upthrust so it accelerates downwards and sinks.