1/41
Looks like no tags are added yet.
characteristics of the ultrasound wave (4)
audible sound ranges b/w 16-20,000 Hz
sound energy > 20,000 = ultrasound
1 Hz = 1 cycle/second
number of collisions undergoes in 1 sec defines the freq of a sound wave and is measured in Hz
characteristics of the ultrasound wave components (3)
frequency
mode
intensity
frequency
1 MHz or 3 MHz
3 MHz used when target tissue is within 1-2cm from body surface (aka superficial)
1 MHz used when target tissue is > 2cm beneath the skin (aka deep)
3 MHz may be used to treat
plantar fasciitis, achilles tendinitis, tennis elbow
1 MHz may be used to treat
soleus, piriformis, hip adductors, or pts with high % of body fat
duty cycle/mode can either me
continuous = thermal effect
pulsed - non-thermal effect
continuous duty cycle/mode (3)
thermal effect
sound energy is constant
u/s energy produced 100% of the time
continuous duty cycle is used
later in the healing process
pulsed duty cycle/mode (3)
non-thermal effect
energy is periodically interrupted
no u/s energy is produced during the off period
pulsed duty cycle is used
during acute inflammatory phase
treatment parameters: power
energy is produced by an u/s generator and is measured in watts (W)
power (2)
function of both pulse width and pulse frequency
represents the amount of energy being produced by the transducer
treatment parameters: intensity
rate at which energy is being delivered per unit area (W/cm2)
intensity (2)
strength of sound waves at a given location within tissue being treated
also referred to as SAI (spatial average intensity)
spatial average intensity (SAI) def
intensity of the u/s beam averaged over the area of the soundhead (central third)
most therapeutic u/s generators are limited to a max output of
3.0 W/cm2 (WHO guidelines)
intensities greater than 10 W/cm2 are used to
destroy tissues (surgically)
intensities less than 0.1 W/cm2 used for
diagnostic purposes
SAI: goal
to select the lowest intensity to achieve the desired therapeutic effect
effective radiating area (ERA)
actual cross sectional area of the beam as it exits the metal end plate
always smaller than the sound head because the crystal is smaller than the sound head
ERA facts (4)
ideally crystal and sound head should be close to the same size
measured 5mm away from sound head
most energy is concentrated at the center of the head
large ERAs produce a more collimated beam vs smaller ERAs
ERA is expressed in
square cm
large ERA
collimated beam
smaller ERA
more divergent beam
spatial average intensity (SAI) def
amount of ultrasound energy passing through the ultrasound head, expressed in watts per square centimeter (W/cm2)
SAI formula
SAI = total watts (W) / effective radiating area (cm2)
beam nonuniformity ratio (BNR) def
indicator of the variability of intensity within the beam
BNR ratio
ratio of the peak intensity : SAI
BNR cont (4)
BNR should fall between 2 and 5
the lower the BNR the more uniform the output
high intensity areas of the beam are called “hot spots”
pt may complain of severe pain or a dull ache
depth of penetration
the higher the freq, the less the sound will diverge or spread out
depth of penetration is inversely related to output freq
collimated def
beam of parallel rays/waves forming a column of energy
due to the depth of penetration heat produced by 1MHz
lasts longer than 3 MHz
in bone u/s travels in
longitudinal and transverse waves
in other biological tissues u/s travels in
ONLY longitudinal waves
acoustic energy can be (4)
transmitted
absorbed
reflected
refracted
acoustic impedance def
a material’s ability to transmit sound
reflection and refraction
occur when energy is transmitted b/w materials with different impedances
standing wave def
a single frequency wave caused by the collision of 2 waves of equal frequency and speed travelling in opposite directions
inc risk of tissue damage
refraction def
the bending of waves as a result of a change in the speed of a wave as it enters a medium of a different density
when energy leaves a dense layer and enters a less dense one the speed inc
tends to occur as it passes through joint spaces
factors influencing energy absorption (2)
tissue (all or part of the energy may be absorbed)
each time some of energy is absorbed/refracted/reflected less energy is available to transmit into deeper tissues
attenuation def
measure of the dec in sound energy as the sound wave travels
factors influencing energy absorption from most → least collagen
1) tendon
2) ligaments
3) cartilage
4) muscle
5) bone