Materials Processing 2

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/20

encourage image

There's no tags or description

Looks like no tags are added yet.

21 Terms

1
New cards

Machining Definition

Substractive

Shapes a component by cutting, shaving, or boring away unwanted material from solid raw stock using cutting tools.

Material is removed as chips

2
New cards

Forging Definition

Froming Process

Shapes the material through bulk plastic deformation and compressive forces rather than material removal

No waste

3
New cards

Grain Machining vs Forging

Machining: cutting tool shears crystal grains, breaking continuous grain lines at the machined surface.

Higher precision, smoother finish.

Forging: Bulk deformation causes the internal grain structure to reorient and flow continuously along the external contours.

4
New cards

Machining defects

Improper cutting speeds, excessive friction, or dull tools can generate microcracks, surface tears, and locked-in residual stresses

5
New cards

Surface Integrity Machining vs Forging

Machining: Induces localized metallurgical alterations near the cut zone, including plastic deformation of near-surface grain structures, heat-affected microstructural alterations, and phase transformations

Forging: Compressive forces close up internal voids or porosity within the bulk material, producing a dense, continuous microstructural network

6
New cards

Mechanical Strength & Fatigue: Machining vs Forging

Forged - superior structural integrity, toughness, and fatigue resistance CUZ continuous grain flow distributes operational loads along intact grain boundaries

Machined - rely on the bulk properties of the starting raw stock

  • localized tensile residual stresses or microcracks from cutting lowers surface fatigue limits


7
New cards

Considerations for machining

Hardness and speed - Hardness ^ = (spindle power^, feed rate v, rigid machines)

Heat and thermal expansion - Friction and heat generate; gentel materials can dull

Corrosion & Post-treatment - Metals rust or chemically degrade = protective/planting/painting coat need.

8
New cards

Surface Characteristics after machining:

Intense thermal and mechanical stresses:

  • Surface Roughness: Creates microscopic, closely spaced peaks and valleys formed by tool edge geometry and feed marks

  • Residual Stresses: Induces locked-in mechanical and thermal stresses within the surface layers due to high cutting forces and localized thermal expansion/contraction[5].

  • Plastic Deformation: Deforms microstructural crystal grains near the cut surface zone[5].

  • Microcracks & Surface Tears: Produces surface damage and micro-cracking caused by excessive cutting heat, improper cutting speeds, or dull cutting tools[5].


9
New cards

Preferred machining method for forming holes in a workpiece

Drilling is the primary and most popular machining method for creating through- or blind holes in raw stock

10
New cards

Four Processes to Modify a Drilled Hole

1.      Reaming: Uses a multi-fluted rotary tool to refine, smooth, and bring a pre-drilled hole to precise dimensional tolerances and an accurate diameter[7].

2.      Boring: Uses a single-point cutting tool to expand or enlarge an existing hole, improving hole concentricity, taper, or internal cylindrical geometry[8].

3.      Tapping: Cuts internal helical screw threads into the wall of a drilled hole so threaded fasteners can be installed[7].

4.      Internal Broaching: Pushes or pulls a multi-toothed cutting tool through a pre-drilled hole to cut internal shapes such as keyways, splines, or non-circular polygons[9][10].

11
New cards

Main difference between shaping and planing

·        In planing, the workpiece is mounted to a moving table that reciprocates against a stationary cutting tool[11][12].

·        In shaping, the workpiece remains stationary (moving only incrementally for feed), while the cutting tool reciprocates linearly across the workpiece.

12
New cards

Process Selection between shaping and planing

·        Planing is chosen for large, heavy workpieces or long flat surfaces and slots, where moving a massive workpiece back and forth under a rigid tool post is more practical than moving a large machine ram[11].

·        Shaping is preferred for smaller components, smaller cut profiles, and lower-volume jobs due to smaller machine footprints and simpler tool ram setups[12].

13
New cards

1.      A twist drill with a diameter of 12 mm is used to drill a through-hole into a steel workpiece. The drill operates at a rotational speed of 600 rpm with a feed rate of 0.20 mm/rev. Calculate the material removal rate (MRR) in mm³/min.

knowt flashcard image
14
New cards

What factors cause tool wear in machining?

·        High Temperatures: Frictional heating at the cutting interface softens tool materials, causing plastic deformation and accelerating chemical diffusion wear[16][17].

·        Excessive Cutting Forces: Heavy feed rates, deep cuts, or hard workpieces place severe mechanical stresses on the tool tip[16].

·        Friction & Mechanical Abrasion: Microscopic hard inclusions within the workpiece rub continuously against the flank and rake faces of the tool[16][18].

·        Improper Operational Parameters: Incorrect cutting speeds, poor feeds, or inadequate lubrication exacerbate tool degradation[16].

15
New cards

How does the use of cutting fluid improve tool life and the surface finish of the workpiece?

·        Tool Life Improvement: Coolants extract thermal energy directly from the cutting zone, maintaining tool hardness and preventing thermal cracking or premature softening[16][19]. Lubricants reduce friction at the tool-chip interface, reducing abrasive wear and cutting forces[16][19].

·        Surface Finish Improvement: Flushes away abrasive metal chips and swarf from the cut zone, preventing chip re-cutting, scratch defects, and built-up edge (BUE) formation on the tool tip[16].

16
New cards

Chemical chemical makeup and atomic arrangements comparison of polymers & metals

  • Polymers: Organic materials composed of large macromolecular chains made of repeating carbon- and hydrogen-based units ("mers")[1][2]. The atoms within individual polymer backbone chains are held together by strong covalent bonds, while adjacent chains interact through weaker secondary van der Waals forces or covalent cross-links[1].

  • Metals: Inorganic substances consisting of metallic atoms arranged in orderly, repeating, three-dimensional crystalline lattice structures bound by delocalized metallic bonding (an electron sea)[


17
New cards

Determine if the magnitude of the following polymer properties would  generally be higher or lower when compared to metals: Elastic modulus, Ultimate Strength, Max Strain (Elongation), Density, Melting Temperature, Electrical/Thermal Conductivity.


  • Elastic Modulus: Lower in polymers compared to metals[6][7].

  • Ultimate Strength: Lower in polymers compared to metals[6][7].

  • Max Strain (Elongation): Higher in polymers compared to metals due to chain uncoiling and sliding under load[7].

  • Density: Lower in polymers compared to metals[6].

  • Melting Temperature: Lower in polymers compared to metals[11][12].

  • Electrical/Thermal Conductivity: Lower in polymers compared to metals (polymers act as electrical and thermal insulators)[7][10].


18
New cards

Generic Stress-Strain Curves: Thermoplastics, Thermosets, Elastomers

  1. Thermoplastics: Linear or branched polymer chain architectures held together by weak secondary bonds[3][13]. They can be repeatedly heated to soften/melt and cooled to solidify without permanent chemical degradation[14][15].

  2. Thermosets: Network structures linked together by dense, irreversible chemical cross-linking that prevents melting upon heating[4].

  3. Elastomers: Lightly cross-linked polymer networks capable of large, reversible elastic deformations when subjected to stress[4][17].


<ol type="1"><li><p><span style="font-family: &quot;Times New Roman&quot;, serif;"><strong>Thermoplastics: Linear or branched polymer chain architectures held together by weak secondary bonds<sup>[3][13]</sup>. They can be repeatedly heated to soften/melt and cooled to solidify without permanent chemical degradation<sup>[14][15]</sup>.</strong></span></p></li><li><p><span style="font-family: &quot;Times New Roman&quot;, serif;"><strong>Thermosets: Network structures linked together by dense, irreversible chemical cross-linking that prevents melting upon heating<sup>[4]</sup>.</strong></span></p></li><li><p><span style="font-family: &quot;Times New Roman&quot;, serif;"><strong>Elastomers: Lightly cross-linked polymer networks capable of large, reversible elastic deformations when subjected to stress<sup>[4][17]</sup>.</strong></span></p></li></ol><p></p>
19
New cards

What are the three primary types of polymers?

  1. Thermoplastics: Linear or branched polymer chain architectures held together by weak secondary bonds[3][13]. They can be repeatedly heated to soften/melt and cooled to solidify without permanent chemical degradation[14][15].

  2. Thermosets: Network structures linked together by dense, irreversible chemical cross-linking that prevents melting upon heating[4].

  3. Elastomers: Lightly cross-linked polymer networks capable of large, reversible elastic deformations when subjected to stress[4][17].


20
New cards

Example of a commodity polymer or product for each of the three main polymer types.

  • Thermoplastic: Polyethylene (PE) used for film wraps/plastic bags, or Polypropylene (PP) used for food containers.

  • Thermoset: Epoxy resin used for structural adhesives/printed circuit boards, or Phenolic resin used for cookware handles.

  • Elastomer: Natural rubber used for vehicle tires, or Silicone used for high-temperature gaskets


21
New cards

What is the glass transition temperature?

Glass transition temperature (Tg) - The critical temperature boundary below which an amorphous or semi-crystalline polymer behaves as a rigid, glassy, and brittle solid, and above which it becomes soft, flexible, and rubbery.

Above Tg, thermal energy ^ = polymer chain segments rotate and slide past one another = drop in the elastic modulus (stiffness) = corresponding increase in ductility and impact resistance

Phenomenon Above Tg Under Shear Loads: In their liquid state above the melting temperature (TmT_m), polymer melts exhibit shear-thinning (non-Newtonian / pseudoplastic) flow behavior25more_horiz. Under increasing shear loads or rates, tangled polymer chains align along the flow direction, causing the apparent viscosity of the melt to decrease