Orgo Lab Final Exam (2026)

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/850

encourage image

There's no tags or description

Looks like no tags are added yet.

851 Terms

1
New cards

[Lab01] What is recrystallization used for?

Purifying organic solids.

2
New cards

[Lab01] Why does a well-ordered, tightly packed crystal lattice matter?

Pure molecules self-assemble into an ordered lattice, giving a narrow melting-point range. Impurities disrupt the lattice.

3
New cards

[Lab01] Ideal recrystallization solvent: behavior when HOT?

Dissolves both the desired compound AND the impurities at/near its boiling point.

4
New cards

[Lab01] Ideal recrystallization solvent: behavior when COLD?

Desired compound is insoluble (or very low solubility); impurities stay soluble.

5
New cards

[Lab01] Why must impurities stay soluble in the cold solvent?

Otherwise they recrystallize together with the target compound.

6
New cards

[Lab01] How much solvent do you use to dissolve the impure solid?

The MINIMUM amount of boiling solvent (gives a saturated solution on cooling).

7
New cards

[Lab01] How are insoluble impurities removed during recrystallization?

Hot gravity filtration.

8
New cards

[Lab01] What happens as the hot solution cools to room temp?

Small pure seed crystals form and act as nucleation sites; more molecules deposit in layers. Slow growth = very pure, shiny crystals.

9
New cards

[Lab01] Possible crystal shapes (depends on nucleation)?

Plates, needles, snowflakes.

10
New cards

[Lab01] Why put the flask in an ice bath after it reaches room temp?

To maximize crystal formation.

11
New cards

[Lab01] How are crystals collected and rinsed?

Vacuum filtration; rinse with ICE-COLD solvent to wash away surface impurities.

12
New cards

[Lab01] What is the "mother liquor"?

The leftover filtrate. It can be reheated, evaporated slightly and cooled for a second crop of crystals.

13
New cards

[Lab01] The 7 steps of recrystallization (in order)

1) choose solvent 2) dissolve solid properly 3) filter 4) cool 5) crystallize 6) isolate 7) purify.

14
New cards

[Lab01] Why is activated carbon used during hot gravity filtration?

It decolorizes: huge surface area and porous structure ADSORBS large, colored impurity molecules.

15
New cards

[Lab01] What colored impurity forms in p-phenetidine and why?

Air oxidation of the amine gives red-brown oxidation products. Pure p-phenetidine is colorless.

16
New cards

[Lab01] What removes the carbon + trapped impurities?

Fluted filter paper during hot gravity filtration, leaving a clear solution.

17
New cards

[Lab01] What functional group is synthesized in Lab 1, and how is it isolated?

An amide (acetophenetidin), isolated from suspension by vacuum filtration.

18
New cards

[Lab01] Solvent selection concept: "hot solubility"

Solvent must completely dissolve compound + impurities at/near boiling.

19
New cards

[Lab01] Solvent selection concept: "cold insolubility"

Target compound must be insoluble/very low solubility at RT or in an ice bath.

20
New cards

[Lab01] Solvent selection concept: "impurity behavior"

Soluble impurities stay dissolved in cold solvent and remain in the mother liquor.

21
New cards

[Lab01] Why dissolve crude solid in a MINIMUM of hot solvent?

Ensures saturation on cooling. Slow cooling lets molecules lock into an ordered lattice (nucleation + growth) and leave impurities in solution.

22
New cards

[Lab01] How do you take a melting point?

Pack dry sample in a capillary tube; insert when apparatus reaches the starting temp; record T when it first melts and T when completely melted (a RANGE).

23
New cards

[Lab01] Melting point ramp rate?

Rate the temp increases: ~5 for general/rough, ~2 for a specific/accurate measurement (degrees per minute).

24
New cards

[Lab01] Plan to show a molecule made by two methods is identical?

Compare melting points, IR, 1H NMR, and TLC (and mixed mp).

25
New cards

[Lab01] Reaction/mechanism types in Lab 1

Amide acetylation (amide formation) via nucleophilic acyl substitution; the study guide also lists Williamson ether synthesis.

26
New cards

[Lab01] Mechanism of acetophenetidin formation (3 stages)

1) HCl protonates amine to ammonium salt 2) Carbon decolorizes 3) NaOAc frees amine; amine lone pair attacks anhydride C=O, tetrahedral intermediate collapses, acetate leaves, giving amide + acetic acid.

27
New cards

[Lab01] Stoichiometry of the acetylation

1 mol p-phenetidin : 1 mol acetic anhydride : 1 mol acetophenetidin (1:1 ratio).

28
New cards

[Lab01] Step 1 (hot water prep): purpose of water and the step

Heat source/supply of hot water for washing and solution prep. Pre-heated because heating large volumes takes a long time.

29
New cards

[Lab01] p-Phenetidine: role

Organic starting material (limiting reagent, an amine); often contains red-brown air-oxidation impurities.

30
New cards

[Lab01] Dilute HCl (3.25%): role

Protonates the amine (-NH2 to -NH3+ Cl-), making a water-soluble salt that dissolves in the aqueous solution.

31
New cards

[Lab01] Activated carbon (charcoal): role

Decolorizing agent; adsorbs large colored impurity molecules onto its surface.

32
New cards

[Lab01] Purpose of Step 2 (purifying p-phenetidine)

Remove colored oxidation impurities by hot gravity filtration, giving a clean acidified solution.

33
New cards

[Lab01] Sodium acetate solution: role

Mild base/buffer; neutralizes excess HCl and converts ammonium salt back to the free amine so it can react.

34
New cards

[Lab01] Acetic anhydride: role

Acylating agent; the free amine attacks it to form the amide bond (acetophenetidin).

35
New cards

[Lab01] Byproduct of the acetylation?

Acetic acid.

36
New cards

[Lab01] Purpose of Step 3 (amide synthesis)

Make the amide, cool in ice bath to maximize solid, isolate crude product by vacuum filtration.

37
New cards

[Lab01] Recrystallization solvent in Lab 1

Water: dissolves compound + impurities hot; lets pure molecules form an orderly lattice on cooling.

38
New cards

[Lab01] Wooden applicator stick in recrystallization: role

Provides nucleation sites for bubbles; promotes smooth boiling and prevents bumping.

39
New cards

[Lab01] Purpose of Step 4 (recrystallization)

Purify crude solid: dissolve in minimum boiling solvent, cool slowly, impurities stay in mother liquor, isolate by vacuum filtration.

40
New cards

[Lab01] Step 1 mechanism correlation: protonation/solubilization

HCl protonates basic -NH2 to ammonium salt, turning a poorly water-soluble organic liquid into a water-soluble ionic salt (homogeneous aqueous solution).

41
New cards

[Lab01] Step 2 mechanism correlation: decolorization

Oxidation impurities are large, conjugated, colored molecules with high surface affinity; they physically adsorb onto carbon and are filtered off hot.

42
New cards

[Lab01] Step 3 mechanism correlation: neutralization + nucleophilic acyl substitution

NaOAc neutralizes HCl, regenerating reactive Ar-NH2. N lone pair attacks electrophilic C=O of acetic anhydride; tetrahedral intermediate collapses, ejecting acetate to form Ar-NH-COCH3.

43
New cards

[Lab01] Why is hot gravity filtration done while the solution is HOT?

Removes solid impurities and carbon while the target stays dissolved; if cooled, impurities would stay with the product.

44
New cards

[Lab01] Why add acetic anhydride only AFTER sodium acetate?

If amine is still -NH3+, its lone pair is tied up and cannot act as a nucleophile. NaOAc must free the amine right before Ac2O or no reaction occurs.

45
New cards

[Lab01] Why separate synthesis from recrystallization?

Synthesis uses an ice bath to rapidly precipitate crude product (max yield). Recrystallization redissolves it and cools SLOWLY so molecules reject impurities and build a pure lattice.

46
New cards

[Lab01] Why an Erlenmeyer flask (not a beaker) to heat recrystallization solvent?

Narrow neck + sloped sides let vapors condense and fall back (mini-reflux), limiting evaporation and boiling dry. A beaker loses solvent too fast.

47
New cards

[Lab01] Why add a wooden stick or boiling chip when heating?

Rough surface gives nucleation sites for bubbles: smooth boiling, prevents bumping (superheated liquid violently splattering).

48
New cards

[Lab01] Why never put a hot Erlenmeyer directly on a cold benchtop?

Thermal shock: uneven contraction can crack/shatter glass. Use an insulating layer (wire mesh, notebook).

49
New cards

[Lab01] Why a STEMLESS funnel for hot gravity filtration?

A long stem lets hot filtrate cool, so product prematurely crystallizes and clogs it. Stemless minimizes contact time/cold surface.

50
New cards

[Lab01] Why wash crystals with ICE-COLD solvent?

Solubility rises with temperature; warm solvent would redissolve product and lower percent recovery. Ice-cold solvent washes impurities with minimal loss.

51
New cards

[Lab01] Why not stir crystals in the Buchner funnel under vacuum?

Stirring breaks the filter-paper seal, creates air channels (poor drying), and can tear paper, contaminating product with cellulose.

52
New cards

[Lab01] Why vent a separatory funnel often with volatile solvents (ether, DCM)?

Vapor pressure builds rapidly (hand heat + mixing). Invert, open stopcock pointed away from people to release pressure so it doesn't blow out the stopper.

53
New cards

[Lab01] How do you tell which layer is aqueous?

Drop test: add a drop of water. If it joins the top layer, the top is aqueous. If it sinks through, the top is organic. Check densities (DCM is denser than water, sits at the bottom).

54
New cards

[Lab01] Why must the mp sample be dry and packed tightly?

Residual solvent acts as an impurity (depresses and broadens mp). Loose packing/air gaps give uneven heat transfer and an artificially broad range.

55
New cards

[Lab01] Your mp is 132-134 and literature (aspirin) is 135. Does this prove purity?

No. A matching mp doesn't guarantee purity (e.g., eutectic mixtures can give a sharp mp). Definitive test: mixed melting point with authentic sample.

56
New cards

[Lab01] Why remove the stopper before opening the sep funnel stopcock?

Otherwise a partial vacuum forms, preventing smooth flow and disturbing the separation.

57
New cards

[Lab01] Can you extract with a water-miscible solvent (ethanol, acetone)?

No. Extraction needs two immiscible phases; miscible solvents form one layer.

58
New cards

[Lab01] Why was HCl mixed with p-phenetidin?

Amine is a weak base, poorly water soluble. HCl protonates it to a water-soluble ammonium salt (-NH3+ Cl-) so it dissolves for homogeneous reaction and carbon decolorization.

59
New cards

[Lab01] Mechanism of p-phenetidin + HCl

N lone pair attacks (abstracts) H+ of H-Cl; H-Cl bonding electrons go onto Cl to form Cl-. Ar-NH2 + HCl gives Ar-NH3+ Cl-.

60
New cards

[Lab01] Purpose of NaOAc(aq)

Mild base/buffer: neutralizes excess acid and shifts equilibrium to free amine (Ar-NH2), which has the lone pair needed to attack acetic anhydride.

61
New cards

[Lab01] 1H NMR of acetophenetidin: ethyl CH3

Triplet ~1.4 ppm (split by adjacent OCH2).

62
New cards

[Lab01] 1H NMR of acetophenetidin: OCH2

Quartet ~4.0 ppm (split by adjacent CH3).

63
New cards

[Lab01] 1H NMR of acetophenetidin: amide CH3 (NHCOCH3)

Singlet ~2.1 ppm.

64
New cards

[Lab01] 1H NMR of acetophenetidin: aromatic H

Multiplet/doublets ~6.8-7.5 ppm (AA'BB' pattern of a para-disubstituted benzene).

65
New cards

[Lab01] 1H NMR of acetophenetidin: amide N-H

Broad singlet ~8.0-8.5 ppm.

66
New cards

[Lab01] Expected NMR impurities in Lab 1

Water (~1.5-1.6 ppm in CDCl3, incomplete drying); acetic acid (~2.1 ppm singlet + exchangeable peak); unreacted p-phenetidin (small residual peaks).

67
New cards

[Lab02] Limitation of melting points for identifying compounds

Many different organic compounds share identical/similar melting points; supports but doesn't prove identity.

68
New cards

[Lab02] Historical identification method

Qualitative chemical tests for functional groups (color change, gas, precipitate).

69
New cards

[Lab02] Example qualitative test: bromine test

Reddish-brown Br2 reacts with alkenes/alkynes to give a colorless product (color disappears).

70
New cards

[Lab02] Drawbacks of qualitative tests

Time-consuming, hazardous reagents, only show presence/absence of a functional group (not the full structure).

71
New cards

[Lab02] What are solid derivatives (2,4-DNPH)?

Unknown aldehydes/ketones reacted with 2,4-DNPH give colored, sharp-melting 2,4-DNP derivatives; their mp is compared to reference books (CRC Handbook).

72
New cards

[Lab02] Limit of the solid-derivative method

Only works for already-known compounds (like matching a fingerprint to a database).

73
New cards

[Lab02] Modern spectroscopy idea

Specific energies of light (vibrational, electronic, nuclear spin) give a unique "molecular fingerprint" for structure elucidation.

74
New cards

[Lab02] What does IR spectroscopy tell you?

Which functional groups are present or absent.

75
New cards

[Lab02] What does NMR spectroscopy tell you?

Carbon skeleton, hydrogen environments and bonding (1H and 13C; 1H used mostly due to time).

76
New cards

[Lab02] Elemental (CHN) analysis: how it works

Burn sample in O2, measure CO2, H2O and nitrogen oxides produced.

77
New cards

[Lab02] How do you get an empirical formula from CHN data?

Convert each % composition to moles (divide by atomic mass), then divide all by the smallest mole value.

78
New cards

[Lab02] What does mass spectrometry give?

Ionizes the molecule with high-energy particles to find mass-to-charge ratio and molecular weight quickly.

79
New cards

[Lab02] What is IHD / DOU used for?

Index of Hydrogen Deficiency (degrees of unsaturation): combined with IR + NMR, narrows structural possibilities to propose a structure.

80
New cards

[Lab02] Exam focus (Lab 2)

Know general 1H NMR shift ranges for carboxylic acids, aldehydes, aromatic protons AND IR wavenumber ranges for C=O, O-H, N-H (see IR & NMR Ranges sheet).

81
New cards

[Lab02] Lab 2 mechanism / reagents

None: Lab 2 is a spectroscopy concept lab with no reaction mechanism or reagent steps.

82
New cards

[Lab03] What is extraction?

Pulling specific compounds out of a complex mixture using differences in solubility or chemical reactivity.

83
New cards

[Lab03] What is solid-liquid extraction?

A solvent is added to a solid matrix (tea leaves, plant material) to dissolve target components and leave solid waste behind.

84
New cards

[Lab03] Hardest part of solid-liquid extraction?

Finding a selective solvent that dissolves only the desired compounds.

85
New cards

[Lab03] Why were old chlorinated solvents (CCl4) abandoned?

Hard to remove completely and serious health risks (e.g., liver damage).

86
New cards

[Lab03] What replaced them as "green" solvents?

Liquid and supercritical CO2.

87
New cards

[Lab03] Why are liquid/supercritical CO2 ideal?

Inexpensive, nonflammable, nontoxic. It returns to a gas at room T/P, so it leaves zero solvent residue.

88
New cards

[Lab03] How is CO2 "green" even though it's a greenhouse gas?

Dry-ice CO2 is captured from existing atmospheric CO2 and only changes physical state; no new CO2 from a reaction. With efficient carbon capture it can be near carbon neutral.

89
New cards

[Lab03] Chromatography definition

A mobile phase (liquid/gas) carries a mixture through a stationary phase (silica gel/alumina); components separate by different speeds.

90
New cards

[Lab03] Polar vs nonpolar compounds on TLC

Polar: interact strongly with polar stationary phase (H-bonding), move slowly (small Rf). Nonpolar: prefer mobile phase, move far (large Rf).

91
New cards

[Lab03] How do chemists tune the mobile phase?

Adjust solvent ratios (e.g., polar methanol with nonpolar hexane) to change eluent polarity.

92
New cards

[Lab03] TLC rule 1: origin line

Draw ~1 cm from the bottom with a soft pencil (never ink).

93
New cards

[Lab03] TLC rule 2: spotting

Small, concentrated spots with capillary spotters; practice on paper towel first.

94
New cards

[Lab03] TLC rule 3: eluent depth

Solvent level must be BELOW the pencil origin line.

95
New cards

[Lab03] TLC rule 4: chamber saturation

Line chamber with filter paper to saturate air with solvent vapor.

96
New cards

[Lab03] When do you remove the TLC plate?

When the solvent front is ~1 cm from the top; immediately mark the solvent front with pencil.

97
New cards

[Lab03] How are TLC spots visualized?

Colored compounds directly; colorless ones as dark spots under short-wave UV (fluorescence quenching). Circle spots immediately in pencil.

98
New cards

[Lab03] Rf range

Always between 0 and 1.

99
New cards

[Lab03] Principle of solid-liquid extraction

Selectively transfers soluble target components from a solid matrix into a liquid solvent using solubility differences.

100
New cards

[Lab03] Spinach extraction: solvent and targets

Acetone penetrates crushed baby spinach to dissolve photosynthetic pigments (chlorophylls, carotenes), leaving debris and sand.