ME 121: P-v Characteristics of a Diesel Engine

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/19

flashcard set

Earn XP

Description and Tags

Comprehensive review flashcards covering experimental apparatus, sensor instrumentation, thermodynamic cycle theory, valve timing, equations, and procedures for ME 121 Diesel Engine testing.

20 Terms

1
New cards

What engine model is tested in this experiment, and what are its key specifications?

The tested engine is a Yanmar L70V, single-cylinder, diesel, internal combustion engine rated at 6.5 HP6.5\,\text{HP}, featuring a compression ratio of 2020, a cylinder bore of 3.1 in3.1\,\text{in} (78 mm78\,\text{mm}), a stroke of 2.5 in2.5\,\text{in} (64 mm64\,\text{mm}), and a total displacement of 19.5 in319.5\,\text{in}^3 (0.32 liters0.32\,\text{liters}).

2
New cards
<p>In internal combustion engine geometry, what do the abbreviations TDC, BDC, and CV represent?</p>

In internal combustion engine geometry, what do the abbreviations TDC, BDC, and CV represent?

TDC stands for Top Dead Center, BDC stands for Bottom Dead Center, and CV stands for Clearance Volume.

3
New cards

How is engine speed maintained, and what is the maximum operating speed limit for the Yanmar L70V?

The engine speed is maintained by a built-in governor and cannot exceed 3600 RPM3600\,\text{RPM}.

4
New cards

How does the fuel injection timing vary with engine speed in the Yanmar L70V engine?

Fuel injection timing is approximately 15∘15^\circ before top dead center (TDC) for speeds up to 2100 RPM2100\,\text{RPM}, and advances to 33∘33^\circ before TDC at 3600 RPM3600\,\text{RPM}.

5
New cards

What are the exact valve opening and closing angles relative to TDC and BDC for the tested Diesel engine?

The inlet valve opens (IVO) at 16∘16^\circ before TDC and closes (IVC) at 36∘36^\circ after BDC. The exhaust valve opens (EVO) at 44∘44^\circ before BDC and closes (EVC) at 8∘8^\circ after TDC.

6
New cards
<p>What engine timing and stroke sequence is illustrated in this diagram?</p>

What engine timing and stroke sequence is illustrated in this diagram?

The schematic displays the four-stroke diesel engine valve operation across two crankshaft rotations (720∘720^\circ), identifying the suction, compression, power, and exhaust phases along with IVO, IVC, EVO, EVC, and FI (fuel injection).

7
New cards

Which sensors are used to determine piston position and detect Top Dead Center (TDC)?

Piston position (cylinder volume) is measured using a Kearfott brushless transmitter/resolver, and the TDC (0∘0^\circ) position is detected using a magnetic pick-up that senses the passing of a set screw on a shaft rotating at engine RPM.

8
New cards

How is cylinder pressure measured during the test, and how is the sensor protected from thermal damage?

Cylinder pressure is measured using a piezoelectric pressure transducer, which is protected from overheating by circulating cooling water through an attached water jacket.

9
New cards
<p>What device is shown attached to the engine output shaft, and how is the engine load controlled?</p>

What device is shown attached to the engine output shaft, and how is the engine load controlled?

A Go-Power water dynamometer is attached to the output shaft. The engine load is varied by adjusting the water flow rate through the dynamometer.

10
New cards

What are the four thermodynamic processes that make up the idealized air-standard Diesel cycle?

  1. Process 1→21 \rightarrow 2: Isentropic compression (reversible and adiabatic)
  2. Process 2→32 \rightarrow 3: Isobaric heat addition
  3. Process 3→43 \rightarrow 4: Isentropic expansion (reversible and adiabatic)
  4. Process 4→14 \rightarrow 1: Isochoric heat rejection
11
New cards
<p>What thermodynamic cycle is depicted in this $$P\text{-}v$$ diagram?</p>

What thermodynamic cycle is depicted in this P-vP\text{-}v diagram?

The idealized air-standard Diesel cycle, showing reversible adiabatic compression (1→21 \rightarrow 2), constant-pressure heat addition (2→32 \rightarrow 3), reversible adiabatic expansion (3→43 \rightarrow 4), and constant-volume heat rejection (4→14 \rightarrow 1).

12
New cards
<p>How does an actual Diesel engine $$P\text{-}V$$ curve differ from the idealized Diesel cycle?</p>

How does an actual Diesel engine P-VP\text{-}V curve differ from the idealized Diesel cycle?

An actual cycle includes intake and exhaust strokes (creating a pumping loop around atmospheric pressure), lacks a truly constant-pressure heat addition phase during expansion, and features smooth, continuous pressure changes rather than sharp, instantaneous state transitions.

13
New cards

Why is the discretized boundary work integral (∑Pavg ΔV\sum P_{\text{avg}}\,\Delta V) calculated only over the compression and power strokes in this experiment?

Because the work contributions of the intake and exhaust strokes are negligible relative to the boundary work produced and absorbed during the compression and power strokes.

14
New cards

What is the difference between Indicated Horsepower (IHP) and Brake Horsepower (BHP)?

Indicated Horsepower (inherent horsepower) is the power developed inside the cylinder by the combustion gases acting on the piston face, whereas Brake Horsepower is the actual mechanical power available and measured at the engine output shaft.

15
New cards

What equation is used to calculate Brake Horsepower (BHP) using the water dynamometer?

BHP=LOAD (lbf)×Moment Arm (0.33 ft)×N (RPM)×2π (radREV)33,000 ft⋅lbfHP⋅min\text{BHP} = \frac{\text{LOAD}\,(\text{lbf}) \times \text{Moment Arm}\,(0.33\,\text{ft}) \times N\,(\text{RPM}) \times 2\pi\,\left(\frac{\text{rad}}{\text{REV}}\right)}{33{,}000\,\frac{\text{ft}\cdot\text{lbf}}{\text{HP}\cdot\text{min}}}

16
New cards

How is the mechanical efficiency (ηMechanical\eta_{\text{Mechanical}}) of the engine defined?

ηMechanical=BHPIHP\eta_{\text{Mechanical}} = \frac{\text{BHP}}{\text{IHP}}, representing the fraction of indicated work produced in the cylinder that is delivered to the output shaft rather than lost to friction.

17
New cards

What formula defines Mean Effective Pressure (MEP) in psi for this engine?

MEP (psi)=HP×(33,000) ft⋅lbfHP⋅min×(12) inft(N2)Power strokesmin×(Vdisplacement) in3\text{MEP}\,(\text{psi}) = \frac{\text{HP} \times (33{,}000)\,\frac{\text{ft}\cdot\text{lbf}}{\text{HP}\cdot\text{min}} \times (12)\,\frac{\text{in}}{\text{ft}}}{\left(\frac{N}{2}\right)\frac{\text{Power strokes}}{\text{min}} \times (V_{\text{displacement}})\,\text{in}^3}

18
New cards

What safety rules must be followed regarding hearing protection and engine clearance?

Ear protection must be worn if remaining in the engine room for more than two minutes, and personnel must maintain at least a 3 foot3\,\text{foot} distance from the operating engine at all times to prevent contact with moving parts and hot surfaces.

19
New cards

What target engine speed and load settings are specified in the lab procedure?

The engine speed is set to approximately 3500 RPM3500\,\text{RPM} to 3600 RPM3600\,\text{RPM}, and data sets are recorded at three engine loads: 1 lbf1\,\text{lbf}, 6 lbf6\,\text{lbf}, and 12 lbf12\,\text{lbf}.

20
New cards

What software is used for computer data acquisition, and what file name is assigned to the exported experimental data?

LabVIEW is used for high-sampling-rate computer data acquisition, and the data files are saved as "pvdata.lvm" in the "PV ENGINE LAB" desktop folder.