1/29
Looks like no tags are added yet.
There are __________ cardinal directions on a compass. (Page 234)
A) 16
B) 6
C) 4
D) 8
D) 8
The 8 cardinal directions on a compass are:
-north
-northeast
-east
-southeast
-south
-southwest
-west
northwest
The difference between magnetic north and true north is called: (Page 234)
A) back azimuth.
B) declination.
C) azimuth.
D) magnetic north.
B) Declination.
Declination is the angular difference between true north (geographic North Pole) and magnetic north (the direction a compass needle points).
This difference matters when firefighters use a compass and map to navigate. Magnetic declination varies depending on your geographic location.
A) Back azimuth: The direction opposite an original azimuth, found by adding or subtracting 180°.
C) Azimuth: A direction measured as an angle clockwise from north, usually from 0° to 360°.
D) Magnetic north: The direction indicated by a magnetic compass needle, not the difference between magnetic and true north.
Study Tip
Declination = the difference.
Think of the deviation between the north shown on a map and the north indicated by your compass. For navigation questions, look for declination when the question asks about the difference between true north and magnetic north.
You need to take this declination into account when using your compass to find a location. This concept is very important because all maps are oriented to: (Page 235)
A) declination north.
B) azimuth ring.
C) true north.
D) magnetic north.
C) True north.
Maps are generally oriented to true north, which is the direction toward the geographic North Pole. Compasses point toward magnetic north, which differs from true north. The angular difference between these two directions is called magnetic declination.
When using a compass with a map, you must account for declination to navigate accurately.
Study Tip:
True north = Geographic North Pole; map reference.
Magnetic north = Where your compass needle points.
Declination = The angle between true north and magnetic north.
A(n) __________ is the horizontal angle of a point measured clockwise from true north. (Page 234)
A) chain
B) azimuth
C) easting value
D) declination
B) Azimuth.
An azimuth is a horizontal angle measured clockwise from a reference direction, usually true north, and expressed in degrees from 0° to 360°.
0° = North
90° = East
180° = South
270° = West
A) Chain: A unit of measurement used in surveying.
C) Easting value: Measures a location's position east or west on a grid.
D) Declination: The angular difference between true north and magnetic north.
Study Tip:
Azimuth = direction in degrees, clockwise from north!
__________ is the difference between magnetic north and true north. Also called magnetic declination or magnetic variation. (Page 234)
A) Azimuth
B) Chain
C) Easting value
D) Declination
D) Declination.
Declination is the angular difference between magnetic north and true north. It is also called magnetic declination or magnetic variation. This difference matters when using a compass with a map because the compass points toward magnetic north, while maps are generally referenced to true north.
A) Azimuth: A horizontal angle measured clockwise from north.
B) Chain: A unit of measurement used in surveying.
C) Easting value: A grid coordinate that indicates how far east a location is.
Study Tip:
Declination = the difference between the two norths!
At the bottom of every USGS map is a diagram that displays the difference and direction between: (Pages 235-236)
A) true north, magnetic north, and calibrated north.
B) absolute north, grid north, and magnetic north.
C) true north, grid north, and magnetic north.
D) true north, declination, and magnetic north.
C) True north, grid north, and magnetic north.
USGS topographic maps include a declination diagram that shows the difference in direction between three north references:
-True north: The direction toward the geographic North Pole.
-Grid north: The direction toward the top of the map's coordinate grid.
-Magnetic north: The direction a magnetic compass needle points.
These directions can differ slightly, so understanding the diagram helps you use a compass and map together accurately.
Study Tip:
The three norths: True, Grid, Magnetic (TGM).
__________ is north according to the earth's axis. (Page 234)
A) Perceived north
B) Magnetic north
C) Actual north
D) True north
D) True north.
True north is the direction toward the geographic North Pole, which is determined by Earth's rotational axis.
Perceived north: Not a standard navigation reference.
Magnetic north: The direction a magnetic compass needle points.
Actual north: Not the standard term used in map and compass navigation.
Study Tip:
True north = Earth's axis and the geographic North Pole.
Percentage of slope is determined by dividing the amount of elevation change by the amount of __________ distance covered (sometimes referred to as "the rise divided by the run") and then multiplying the result by __________. (Page 238)
A) linear; 50
B) horizontal; 100
C) linear; 100
D) vertical; 100
B) Horizontal; 100.
Percentage of slope is calculated by dividing the elevation change (the rise) by the horizontal distance traveled (the run) and multiplying by 100.
A pace is measured by: (Page 239)
A) two walking steps heel to toe.
B) four natural walking steps.
C) two natural walking steps.
D) five natural walking steps.
C) Two natural walking steps.
In land navigation, a pace is typically counted as two natural walking steps, or one complete stride (for example, left foot to left foot). Firefighters use pace counting to estimate distance traveled when navigating terrain.
1 pace = 2 steps. Pace counting helps you estimate distance when navigating in the field.
A chain is a unit of measure in land survey equaling 66 ft (20.1 m); 80 chains is equal to: (Page 239)
A) 1 mile.
B) a pace.
C) ¼ mile.
D) ½ mile.
A) 1 mile.
A chain is a unit of land measurement equal to 66 feet (20.1 meters).
Study Tip:
80 chains = 1 mile. This is useful for land navigation, surveying, and wildland firefighting.
The __________ is a system of navigational satellites operated by the U.S. Department of Defense and available for civilian use. It can track objects anywhere in the world with an accuracy of approximately 40 to 300 ft. (Page 240)
A) global positioning system (GPS)
B) truncated repeater
C) global navigating system (GNS)
D) cellular positioning system (CPS)
A) Global positioning system (GPS).
The Global Positioning System (GPS) is a satellite-based navigation system developed and operated by the U.S. Department of Defense. It is available for civilian use and helps determine a person's or object's location anywhere in the world.
GPS is commonly used in land navigation, mapping, emergency response, and wildland firefighting.
B) Truncated repeater: Not a satellite-based navigation system.
C) Global navigating system (GNS): Not the correct name for the U.S. satellite navigation system.
D) Cellular positioning system (CPS): Uses cellular network information rather than the GPS satellite system.
Study Tip:
GPS = Global Positioning System = satellites that help determine your location. The accuracy range given in the question is the textbook's stated range; actual GPS accuracy varies depending on equipment and conditions.
Topographic maps are a representation of the earth's surface. They are also called __________ maps. (Page 240)
A) elevation
B) relief terrain
C) global terrain
D) quadrangle
D) Quadrangle.
Topographic maps are often called quadrangle maps because USGS maps traditionally cover a specific rectangular area of land. They show natural and human-made features, including elevation, hills, valleys, roads, and streams.
A) Elevation: Refers to the height of a location above a reference point.
B) Relief terrain: Describes variations in the land's elevation, not the standard map name.
C) Global terrain: Not the standard term for USGS topographic maps.
Study Tip:
Topographic map = quadrangle map when studying USGS maps and land navigation.
The horizontal lines that run east and west around Earth are called: (Page 240)
A) longitude.
B) parallels.
C) meridians.
D) latitude.
B) Parallels.
Parallels are imaginary lines that run east and west around Earth. They measure latitude, or how far north or south a location is from the Equator.
A) Longitude: Measures distance east or west of the Prime Meridian.
C) Meridians: Lines that run north and south between the poles.
D) Latitude: The measurement of position north or south, not the name for the lines themselves.
Study Tip:
Parallels = Latitude = East/West lines
Meridians = Longitude = North/South lines
The vertical lines that run north and south are called: (Page 240)
A) parallels.
B) latitude.
C) meridians.
D) longitude.
C) Meridians.
Meridians are imaginary lines that run north and south between the North Pole and the South Pole. They are used to measure longitude, which identifies how far east or west a location is from the Prime Meridian.
A) Parallels: Lines that run east and west around the Earth.
B) Latitude: Measures distance north or south of the Equator.
D) Longitude: The measurement of position east or west, not the name for the lines themselves.
Study Tip:
Meridians = Longitude = North/South lines
Parallels = Latitude = East/West lines
__________ is a point north or south of the equator. (Page 240)
A) Longitude
B) Parallels
C) Latitude
D) Meridians
C) Latitude.
Latitude measures how far north or south a location is from the Equator. It is measured in degrees, from 0° at the Equator to 90° north or south at the poles.
A) Longitude: Measures how far east or west a location is from the Prime Meridian.
B) Parallels: Imaginary lines that run east and west around Earth and represent lines of latitude.
D) Meridians: Imaginary lines that run north and south between the poles and represent lines of longitude.
Study Tip:
Remember latitude = north or south and longitude = east or west!
__________ is a point on Earth's surface that is east or west of what we call the prime meridian. (Page 241)
A) Meridians
B) Parallels
C) Latitude
D) Longitude
D) Longitude.
Longitude measures how far east or west a location is from the Prime Meridian, which is located at 0° longitude in Greenwich, England. Longitude is measured in degrees, up to 180° east or west.
A) Meridians: Imaginary lines that run north and south and represent longitude.
B) Parallels: Imaginary lines that run east and west and represent latitude.
C) Latitude: Measures how far north or south a location is from the Equator.
Study Tip:
Latitude = North/South
Longitude = East/West
Each degree of latitude and longitude is broken down into: (Page 241)
A) 60 minutes.
B) 60 seconds.
C) meridians.
D) parallels.
A) 60 minutes.
Each degree of latitude and longitude is divided into 60 minutes, and each minute is further divided into 60 seconds. These smaller units allow you to identify locations more precisely on a map.
B) 60 seconds: Each minute, not each degree, contains 60 seconds.
C) Meridians: Imaginary lines running north and south that represent longitude.
D) Parallels: Imaginary lines running east and west that represent latitude.
Study Tip:
Remember the coordinate breakdown:
1 degree = 60 minutes
1 minute = 60 seconds
This is important for reading coordinates during land navigation!
Each minute is broken down into: (Page 241)
A) parallels.
B) 60 seconds.
C) meridians.
D) 60 minutes.
B) 60 seconds.
In geographic coordinates, each minute of latitude or longitude is divided into 60 seconds. This allows locations to be measured with greater precision when navigating with maps or GPS.
A) Parallels: Imaginary lines that run east and west and represent latitude.
C) Meridians: Imaginary lines that run north and south and represent longitude.
D) 60 minutes: Each degree is divided into 60 minutes, not each minute.
Study Tip:
1 degree = 60 minutes
1 minute = 60 seconds
These measurements help you pinpoint an exact location on Earth!
A(n) __________ is a type of topographic map. (Page 242)
A) elevation gain map
B) adjusted relief map
C) meridian map
D) contour relief map
D) Contour relief map.
A contour relief map is a type of topographic map that uses contour lines to represent the shape and elevation of the land. These lines help identify hills, valleys, ridges, and steep or gentle slopes.
A) Elevation gain map: Not a standard type of topographic map.
B) Adjusted relief map: Not a standard map classification.
C) Meridian map: Meridians are lines of longitude used to identify locations on Earth.
Study Tip:
Remember contour lines = elevation and terrain shape. Lines close together indicate a steep slope, while lines farther apart indicate a gentler slope.
A __________ is a line of equal elevation on the ground that delineates the same elevation above sea level. (Page 243)
A) meridian
B) latitude
C) parallel
D) contour line
D) Contour line.
A contour line connects points on a map that have the same elevation above sea level. Contour lines help firefighters and other navigators understand the shape of the terrain, including hills, valleys, ridges, and slopes.
A) Meridian: A line running north and south that represents longitude.
B) Latitude: Measures how far north or south a location is from the Equator.
C) Parallel: An imaginary line running east and west that represents latitude.
Study Tip:
Remember contour lines = equal elevation. Lines close together indicate steep terrain, while lines farther apart indicate a gentler slope.
On a contour map, every 4th or 5th line is printed darker. This is called a(n): (Page 243)
A) parallel.
B) latitude.
C) contour line.
D) index contour.
D) Index contour
An index contour is a contour line printed darker or thicker than the others, usually every fourth or fifth line on a topographic map. It often includes an elevation label to make it easier to determine the land's elevation.
A) Parallel: Lines of latitude that run east-west around the Earth, not elevation lines on a contour map.
B) Latitude: Measures distance north or south of the Equator; it does not represent elevation.
C) Contour line: A line connecting points of equal elevation, but this is the general term, not the specific name for the darker line.
Study tip
Remember: "Index = Important." Index contour lines are darker, often labeled, and help you quickly identify elevation on a map.
A(n) __________ line represents areas either manmade or natural that are lower than the immediate surrounding terrain. (Page 243)
A) contour
B) parallel
C) depression contour
D) index contour
C) Depression contour
A depression contour represents a natural or manmade area that is lower than the surrounding terrain, such as a crater, sinkhole, or excavated pit. These contour lines typically have small tick marks called hachures pointing toward the lower ground.
A) Contour: A general line connecting points of equal elevation; it does not specifically indicate a depression.
B) Parallel: Refers to lines of latitude running east-west around the Earth, not low areas of terrain.
D) Index contour: A darker, thicker contour line used to make elevation easier to read on a map.
Study tip
Remember: "Depression = Down." Depression contours indicate ground that dips below the surrounding land. Look for the small inward-pointing tick marks (hachures) to identify them on a topographic map.
The closer the contour lines are together, the __________ the slope will be. (Page 244)
A) steeper
B) flatter
C) less intense
D) more intense
A) Steeper
When contour lines are close together on a topographic map, the elevation changes over a short horizontal distance, indicating a steeper slope. When contour lines are far apart, the slope is gentler or flatter.
B) Flatter: Flat or gentle slopes have contour lines spaced farther apart.
C) Less intense: This is not the standard term used to describe slope steepness on a contour map.
D) More intense: Although it might suggest a steep slope, it is not the correct geographic term. Steeper is the precise answer.
Study tip
Remember: "Close lines = Climb steep; spread lines = Slope sweet."
Close together = steep slope.
Far apart = gentle slope.
Evenly spaced = uniform slope.
A __________ is a low topographic point between two hills or summits. (Page 244)
A) ridge
B) chimney
C) draw
D) saddle
D) Saddle
A saddle is a low point between two hills, peaks, or summits. It resembles a horseback saddle, with higher ground on either side and lower ground in between.
A) Ridge: An elongated area of high ground, often forming a crest between slopes.
B) Chimney: A vertical structure or a narrow rock formation, not a low point between summits.
C) Draw: A small, natural drainage course or depression on a hillside, often shaped like a shallow valley.
Study tip
Remember: "A saddle sits between two peaks." Picture a horseback saddle resting between two raised points. On a topographic map, contour lines form an hourglass-like pattern around a saddle.
A __________ is an area of lowland between two hills or mountains. (Page 244)
A) draw
B) saddle
C) chimney
D) valley
D) Valley
A valley is a low area of land between hills or mountains. Valleys are often formed by rivers, streams, or glaciers and may have a river or stream running through them.
A) Draw: A small drainage feature on a hillside where water flows downhill; it is generally smaller than a valley.
B) Saddle: A low point between two peaks or summits, rather than an extended area of lowland.
C) Chimney: A narrow vertical rock formation or structure, not a low area between hills or mountains.
Study tip
"Valleys lie between hills."
Valley: Lowland between hills or mountains.
Saddle: Low point between two summits.
Draw: Small drainage channel on a slope.
Ridge: Long, narrow area of high ground.
The __________ system is a method of tracking boundaries with landmarks, lines, and words. (Page 244)
A) Public Land Survey System
B) GPS
C) topographic survey
D) metes and bounds
D) Metes and bounds
The metes and bounds system describes property boundaries using measurements, directions, distances, and identifiable landmarks or natural features. It uses written descriptions to define the exact limits of a piece of land.
A) Public Land Survey System: Divides land into a grid of townships and sections using principal meridians and baselines.
B) GPS: Uses satellite signals to determine geographic positions; it is not a traditional property-boundary description system.
C) Topographic survey: Measures and maps land features and elevations, rather than specifically describing property boundaries through written directions and landmarks.
Study tip
Remember: "Metes = Measurements; Bounds = Boundaries."
Metes and bounds describes property by distances, directions, and landmarks. If a question mentions property lines described by following a creek, road, or tree, think metes and bounds.
The __________, also called the township and range survey system or the rectangular survey system, is a method of dividing and tracking public land locations and boundaries. (Page 248)
A) metes and bounds
B) topographic survey
C) GPS
D) Public Land Survey System
D) Public Land Survey System
The Public Land Survey System (PLSS) is also known as the township and range system or the rectangular survey system. It divides public land into a grid using principal meridians, baselines, townships, ranges, and sections to identify land locations and boundaries.
A) Metes and bounds: Describes property boundaries using distances, directions, and landmarks rather than a rectangular grid.
B) Topographic survey: Maps land features, elevations, and terrain rather than dividing public land into townships and ranges.
C) GPS: Uses satellite signals to determine geographic locations; it is not a land-survey division system.
Study tip
Remember: "PLSS = Public Land in Squares."
Think of a checkerboard grid. The PLSS divides land into townships, ranges, and sections.
Bonus fact: One standard section contains 640 acres, and a standard township contains 36 sections (about 23,040 acres).
__________ is a special grid system consisting of 60 north-south zones that are only 6 degrees of longitude wide. (Page 249)
A) Metes and bounds
B) Topographic survey
C) Public Land Survey System
D) UTM
D) UTM
UTM (Universal Transverse Mercator) is a coordinate system that divides most of the world into 60 north-south zones. Each zone is 6 degrees of longitude wide and is used to identify locations accurately on maps.
A) Metes and bounds: Describes property boundaries using distances, directions, and landmarks.
B) Topographic survey: Maps land elevations and physical features, rather than dividing the world into 60 longitude zones.
C) Public Land Survey System: Divides public land into townships, ranges, and sections, primarily in the United States.
Study tip
Remember: "UTM = Universal Zones on a Map."
Memorize these two numbers for exams:
60 zones worldwide.
6 degrees of longitude per zone.
To locate the UTM coordinates on a topographic map, look at the __________ to locate the blue tick marks. (Page 251)
A) margin
B) parallels
C) contours
D) legend
A) Margin
To locate UTM (Universal Transverse Mercator) coordinates on a topographic map, look at the map margin, where blue tick marks indicate UTM grid coordinates. These marks help you identify locations using the map's coordinate system.
B) Parallels: Lines of latitude that run east-west around the Earth.
C) Contours: Lines connecting points of equal elevation, used to show terrain shape.
D) Legend: Explains the symbols and colors used on the map; it does not indicate the location of UTM tick marks.
Study tip
Remember: "UTM ticks are at the edges." Look along the map's margins for coordinate tick marks that help you pinpoint locations.
The __________ is a key accompanying a map that shows information needed to interpret that map. (Page 242)
A) chain
B) sub-map
C) azimuth
D) legend
D) Legend
A legend, also called a map key, explains the symbols, colors, and patterns used on a map so you can correctly interpret the information it displays.
A) Chain: A unit of measurement used in surveying, equal to 66 feet.
B) Sub-map: Not the standard term for the key that explains map symbols.
C) Azimuth: A direction measured as an angle clockwise from north, typically from 0° to 360°.
Study tip
Remember: "Legend = Learn the symbols."
When a question asks which part of a map explains its symbols and colors, choose legend or map key.