P Post-test 4 (Aircraft Construction, Repair, and Modification)

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/49

encourage image

There's no tags or description

Looks like no tags are added yet.

50 Terms

1
New cards

1. If the cabin rate of climb is too great, the control should be adjusted to cause the

A. outflow valve to close slower.

B. outflow valve to close faster.

C. cabin compressor speed to decrease.

D. All of the above

B. outflow valve to close faster.

2
New cards

2. The oxyacetylene flame used for aluminum welding should

A. be neutral and soft.

B. be slightly oxidizing.

C. contain an excess of acetylene and leave the tip at a relatively low speed.

D. None of the above

A. be neutral and soft.

3
New cards

3. Hydraulic system thermal relief valves are set to open at a

A. lower pressure than the system relief valve.

B. higher pressure than the system relief valve.

C. lower pressure than the system pressure regulator.

D. None of the above

B. higher pressure than the system relief valve.

4
New cards

4. Which heat-treating process of metal produces a hard, wear-resistant surface over a strong, tough core?

A. Case hardening.

B. Annealing.

C. Tempering.

D. All of the above

A. Case hardening.

5
New cards

5. In brake service work, the term 'bleeding brakes' is the process of

A. withdrawing air only from the system.

B. withdrawing fluid from the system for the purpose of removing air that has entered the system.

C. replacing small amounts of fluid in reservoir.

D. None of the above

B. withdrawing fluid from the system for the purpose of removing air that has entered the system.

6
New cards

6. What is the function of a cam incorporated in a nose gear shock strut?

A. Provides an internal shimmy damper.

B. Straightens the nosewheel.

C. Provides steering of aircraft during ground operation.

D. None of the above

B. Straightens the nosewheel.

7
New cards

7. What can be done to eliminate or minimize the microbial growth problem in an aircraft jet fuel tank?

A. Use anti-icing and antibacterial additives.

B. Add CO(2) as a purgative.

C. Keep the fuel tank topped off.

D. None of the above

A. Use anti-icing and antibacterial additives.

8
New cards

8. Which of the following copper electrical cable sizes should be selected to replace a No. 6 aluminum electrical cable?

A. No. 4.

B. No. 6.

C. No. 8.

D. None of the above

B. No. 6.

9
New cards

9. When repairing puncture-type damage of a metal faced laminated honeycomb panel, the edges of the doubler should be tapered to

A. two times the thickness of the metal.

B. 100 times the thickness of the metal.

C. whatever is desired for a neat, clean appearance.

D. None of the above

B. 100 times the thickness of the metal.

10
New cards

10. Which of the following factors must be taken into consideration when determining the wire size to use for an aircraft installation?

1. Mechanical strength.

2. Allowable power loss.

3. Ease of installation.

4. Resistance of current return path through the aircraft structure.

5. Permissible voltage drop.

6. Current carrying capability of the conductor.

7. Type of load (continuous or intermittent).

A. 2, 5, 6, 7.

B. 1, 2, 4, 5.

C. 2, 4, 6, 7.

D. All of the above

A. 2, 5, 6, 7.

11
New cards

11. When riveting dissimilar metals together, what precautions must be taken to prevent an electrolytic action?

A. Treat the surfaces to be riveted together with a process called anodic treatment.

B. Place a protective separator between areas of potential electrical difference.

C. Avoid the use of dissimilar metals by redesigning the unit according to the recommendations outlined in AC 43.13-1A.

D. All of the above

B. Place a protective separator between areas of potential electrical difference.

12
New cards

12. Why do tire and wheel manufacturers often recommend that the tires on split rim wheels be deflated before removing the wheel from the axle?

A. To relieve the strain on the wheel retaining nut and axle threads.

B. As a safety precaution in case the bolts that hold the wheel halves together have been damaged or weakened.

C. To remove the static load imposed upon the wheel bearings by the inflated tire.

D. None of the above

B. As a safety precaution in case the bolts that hold the wheel halves together have been damaged or weakened.

13
New cards

13. Which material cannot be heat treated repeatedly without harmful effects?

A. Unclad aluminum alloy in sheet form.

B. 6061-T9 stainless steel.

C. Clad aluminum alloy.

D. All of the above

C. Clad aluminum alloy.

14
New cards

14. An automatic damping action occurs at the steer damper if for any reason the flow of high-pressure fluid is removed from the

A. outlet of the steer damper.

B. inlet of the steer damper.

C. replenishing check valve.

D. All of the above

B. inlet of the steer damper.

15
New cards

15. When drilling stainless steel, the drill used should have an included angle of

A. 90 degrees and turn at a low speed.

B. 118 degrees and turn at a high speed.

C. 140 degrees and turn at a low speed.

D. None of the above

C. 140 degrees and turn at a low speed.

16
New cards

16. The major advantages of alternating current (AC) over direct current (DC) is the fact that its current and voltage can easily be increased or decreased

A. by means of a inverter.

B. by means of a rectifier.

C. by means of a transformer.

D. None of the above

C. by means of a transformer.

17
New cards

17. How is the cabin pressure of a pressurized aircraft usually controlled?

A. By a pressure-sensitive switch that causes the pressurization pump to turn on or off as required.

B. By an automatic outflow valve that dumps all the pressure in excess of the amount for which it is set.

C. By a pressure-sensitive valve that controls the output pressure of the pressurization pump.

D. None of the above

B. By an automatic outflow valve that dumps all the pressure in excess of the amount for which it is set.

18
New cards

18. Internal leakage in a brake master cylinder unit can cause

A. fading brakes.

B. slow release of brakes.

C. the pedal to slowly creep down while pedal pressure is applied.

D. All of the above

C. the pedal to slowly creep down while pedal pressure is applied.

19
New cards

19. A certificated mechanic without an inspection authorization who signs the appropriate block on FAA Form 337 is doing what?

A. Certifying that the work was done in accordance with the requirements of 14 CFR part 43.

B. Approving the work for return to service.

C. Certifying the maintenance information used as FAA-approved data.

D. All of the above

A. Certifying that the work was done in accordance with the requirements of 14 CFR part 43.

20
New cards

20. Aircraft flight control trim systems must be designed and installed so that the

A. pilot can determine the relative position of the trim tab from the cockpit.

B. operating control and the trim tab will always move in the same direction.

C. trim system will disengage or become inoperative if the primary flight control system fails.

D. None of the above

A. pilot can determine the relative position of the trim tab from the cockpit.

21
New cards

21. An aircraft owner was provided a list of discrepancies on an aircraft that was not approved for return to service after an annual inspection. Which of the following statements is/are true concerning who may correct the discrepancies?

1. Only a mechanic with an inspection authorization.

2. An appropriately rated mechanic.

3. Any certificated repair station.

A. 2 & 3.

B. 2

C. 1

D. None of the above

B. 2

22
New cards

22. The strength of a well-designed and properly prepared wood splice joint is provided by the

A. bearing surface of the wood fibers.

B. glue.

C. reinforcement plates.

D. None of the above

B. glue.

23
New cards

23. Which maintenance record entry best describes the action taken for a control cable showing approximately 20 percent wear on several of the individual outer wires at a fairlead?

A. Wear within acceptable limits, repair not necessary.

B. Removed and replaced the control cable and rerigged the system.

C. Cable repositioned, worn area moved away from fairlead.

D. All of the above

A. Wear within acceptable limits, repair not necessary.

24
New cards

24. Which statement is true with respect to an aircraft equipped with hydraulically operated multiple-disk type brake assemblies?

A. There are no minimum or maximum disk clearance checks required due to the use of self-compensating cylinder assemblies.

B. Do not set parking brake when brakes are hot.

C. No parking brake provisions are possible for this type of brake assembly.

D. All of the above

B. Do not set parking brake when brakes are hot.

25
New cards

25. A potted compound repair on honeycomb can usually be made on damages less than

A. 4 inches in diameter.

B. 2 inches in diameter.

C. 1 inch in diameter.

D. None of the above

C. 1 inch in diameter.

26
New cards

26. A typical large transport aircraft fuel manifold system allows how many of the following?

1. All tanks can be serviced through a single connection.

2. Any engine can be fed from any tank.

3. All engines can be fed from all tanks simultaneously.

4. A damaged tank can be isolated from the rest of the fuel system.

A. 1 and 2.

B. 1, 2, and 3.

C. 1, 2, 3, and 4.

D. None of the above

C. 1, 2, 3, and 4.

27
New cards

27. Movement about the lateral axis (pitch) in a helicopter is effected by movement of the

A. collective pitch control.

B. cyclic pitch control.

C. tail rotor pitch control.

D. All of the above

B. cyclic pitch control.

28
New cards

28. To be eligible for recharging, a DOT 3HT oxygen cylinder must have been hydrostatically tested every three years and be retired from service after

A. 24 years or 4,380 filling cycles.

B. 15 years or 10,000 filling cycles.

C. 10 years or 5,000 filling cycles.

D. None of the above

A. 24 years or 4,380 filling cycles.

29
New cards

29. Which instruments are connected to an aircraft's pitot-static system?

1. Vertical speed indicator.

2. Cabin altimeter.

3. Altimeter.

4. Cabin rate-of-change indicator.

5. Airspeed indicator.

A. 1, 2, 3, 4, and 5.

B. 1, 2, and 4.

C. 1, 3, and 5.

D. All of the above

C. 1, 3, and 5.

30
New cards

30. A barometric altimeter indicates pressure altitude when the barometric scale is set at

A. 29.92" Hg.

B. 14.7" Hg.

C. field elevation.

D. None of the above

A. 29.92" Hg.

31
New cards

31. Long Range Navigation (LORAN) systems determine aircraft location by

A. measuring the inertial forces acting on the aircraft.

B. means of pulsed signals transmitted from ground stations.

C. means of signals transmitted to and from navigation satellites.

D. None of the above

B. means of pulsed signals transmitted from ground stations.

32
New cards

32. What is the minimum edge distance for aircraft rivets?

A. Two times the diameter of the rivet shank.

B. Two times the diameter of the rivet head.

C. Three times the diameter of the rivet shank.

D. None of the above

A. Two times the diameter of the rivet shank.

33
New cards

33. The evacuation of a vapor-cycle cooling system removes any water that may be present by

A. drawing out the liquid.

B. raising the boiling point of the water and drawing out the vapor.

C. lowering the boiling point of the water and drawing out the vapor.

D. None of the above

C. lowering the boiling point of the water and drawing out the vapor.

34
New cards

34. What is the condition of the refrigerant as it leaves the evaporator of a vapor-cycle cooling system?

A. Low-pressure liquid.

B. Low-pressure vapor.

C. High-pressure vapor.

D. None of the above

B. Low-pressure vapor.

35
New cards

35. Which of the following are characteristic of a chemical or solid state oxygen system?

1. An adjustable oxygen release rate.

2. A volume storage capacity about three times that of compressed oxygen.

3. The system generators are inert below 400°F even under severe impact.

4. A distribution and regulating system similar to gaseous oxygen systems.

A. 2 & 3.

B. 3 & 4.

C. 1 & 2.

D. None of the above

A. 2 & 3.

36
New cards

36. Corrosion should be removed from magnesium parts with a

A. stiff, nonmetallic brush.

B. silicon carbide brush.

C. carborundum abrasive.

D. All of the above

A. stiff, nonmetallic brush.

37
New cards

37. Which of the following are characteristic of a chemical or solid state oxygen system?

1. An adjustable oxygen release rate.

2. A volume storage capacity about three times that of compressed oxygen.

3. The system generators are inert below 400 degrees F even under severe impact.

4. A distribution and regulating system similar to gaseous oxygen systems.

A. 2 & 3.

B. 3 & 4.

C. 1 & 2.

D. All of the above

A. 2 & 3.

38
New cards

38. Which motor would be most likely to have an armature brake?

A. Starter motor.

B. Landing light retraction motor.

C. Inverter drive motor.

D. None of the above

B. Landing light retraction motor.

39
New cards

39. In Gas Tungsten Arc (GTA) welding, a stream of inert gas is used to

A. prevent the formation of oxides in the puddle.

B. concentrate the heat of the arc and prevent its dissipation.

C. lower the temperature required to properly fuse the metal.

D. None of the above

A. prevent the formation of oxides in the puddle.

40
New cards

40. An embossed letter "H" on an air valve core stem

A. is the manufacturer's trademark.

B. indicates hydraulic type.

C. indicates high-pressure type.

D. All of the above

C. indicates high-pressure type.

41
New cards

41. On an air valve core stem, what indicates high-pressure type?

A. An embossed letter 'NP.'

B. An embossed letter 'HP.'

C. An embossed letter 'H.'

D. All of the above

C. An embossed letter 'H.'

42
New cards

42. Power boost brake systems are used on aircraft that have

A. high landing speeds.

B. low normal hydraulic system pressure.

C. more than one brake assembly per axle.

D. All of the above

A. high landing speeds.

43
New cards

43. In examining and evaluating a welded joint, a mechanic should be familiar with

A. likely ambient exposure conditions and intended use of the part, along with type of weld and original part material composition.

B. the welding technique, filler material, and temperature range used.

C. the parts, proportions, and formation of a weld.

D. None of the above

A. likely ambient exposure conditions and intended use of the part, along with type of weld and original part material composition.

44
New cards

44. Fuel is moved overboard in most fuel jettison systems by

A. boost pumps.

B. gravity.

C. gravity and engine-driven fuel pumps.

D. None of the above

A. boost pumps.

45
New cards

45. Which of the following are the desired effects of using Alodine on aluminum alloy?

1. A slightly rough surface.

2. Relieved surface stresses.

3. A smooth painting surface.

4. Increased corrosion resistance.

A. 3 and 4.

B. 1, 2, and 4.

C. 1 and 4.

D. None of the above

C. 1 and 4.

46
New cards

46. A radar altimeter indicates

A. flight level (pressure) altitude.

B. altitude above sea level.

C. altitude above ground level.

D. None of the above

C. altitude above ground level.

47
New cards

47. What icing condition may occur when there is no visible moisture present?

A. Injector ice.

B. Inlet ice.

C. Carburetor ice.

D. None of the above

C. Carburetor ice.

48
New cards

48. Why are the iron cores of most induction coils laminated?

A. To reduce the core reluctance.

B. To increase the core permeability.

C. To reduce the effects of eddy currents.

D. None of the above

C. To reduce the effects of eddy currents.

49
New cards

49. An emergency supply of fluid is often retained in the main hydraulic system reservoir by the use of a standpipe. The supply line is connected to the

A. inlet of the main hydraulic system.

B. inlet of the emergency pump.

C. outlet of the main system pump.

D. None of the above

A. inlet of the main hydraulic system.

50
New cards

50. When bleeding aircraft brakes, one of the indications that the air has been purged from the system is

A. partial brake pedal travel.

B. full brake pedal travel.

C. firm brake pedals.

D. All of the above

C. firm brake pedals.