1/42
Comprehensive practice flashcards covering Chapter 4: X-Ray Circuit learning objectives, including electrostatics, electrodynamics, Ohm's law, circuit components, magnetism, transformers, and x-ray circuit operation.
What is the difference between electrostatics and electrodynamics?
Electrostatics studies stationary electric charges, whereas electrodynamics studies electric charges in motion (electricity).
Which subatomic particles carry charge, and which are free to move in solid conductors?
Electrons have a negative charge and protons have a positive charge; only electrons are free to move in solid conductors.
How is electric charge measured, and how many electrons correspond to one unit of this charge?
Electric charge is measured in coulombs (C); 1C is approximately 6.25×1018 electrons.
What are the fundamental electrostatic principles regarding charge interaction, location, and distribution on conductors?
Like charges repel and unlike charges attract; force increases with charge and decreases with the square of distance (Coulomb's law); charges reside on the outside of conductors; charge concentrates at areas of greatest curvature; and only negative charges (electrons) move in solid conductors.
Through what three processes can electrification occur?
Electrification can occur by friction, contact, or induction (which is charge redistribution without direct contact).
What condition is required for an electric current to flow, and in what direction do electrons travel?
An electric current requires a potential difference; electrons move from an area of electron abundance toward an area of electron deficiency.
What is electric potential (voltage), and what does the kVp selection control in x-ray equipment?
Electric potential (V) is the ability to do work due to separation of charges (the electrical potential difference driving current) measured in volts. The kVp selection controls the potential applied to the x-ray tube and the energy/penetrating ability of the x-ray beam.
What is electric current, how is it measured, and how is tube current expressed?
Electric current (I) is the rate of flow of electric charge, measured in amperes (A), where 1A=1C of charge per second. Tube current is expressed in milliamperes (mA).
What is resistance, and what is its unit of measurement?
Resistance (R) is the opposition to the flow of electric current, measured in ohms (symbol: Ω).
What is the distinction between direct current (DC) and alternating current (AC), and what is the frequency of U.S. mains AC?
Direct current (DC) flows in one direction, while alternating current (AC) periodically reverses direction as source polarity changes. U.S. mains AC operates at 60cycles per second (60Hz).
Which four physical factors determine the resistance of a conductor?
Resistance depends on material, length, cross-sectional area, and temperature. A longer conductor has more resistance, a larger cross-sectional area has less resistance, and in metallic conductors, increasing temperature increases resistance.
What are the algebraic expressions for Ohm's law?
V=I×R, I=RV, and R=IV, where V=voltage, I=current, and R=resistance.
What rules govern current, resistance, and voltage in a series circuit?
Current is the same at every point (IT=I1=I2=I3); total resistance is the sum of individual resistances (RT=R1+R2+R3); and total voltage is the sum of voltage drops (VT=V1+V2+V3, also expressed as VT=IT×RT).
What rules govern voltage, current, and resistance in a parallel circuit?
Voltage is equal across all branches (VT=V1=V2=V3); total current is the sum of branch currents (IT=I1+I2+I3); and total resistance is found via the reciprocal rule (RT1=R11+R21+R31, also expressed as VT=IT×RT).
In the series circuit practice example with 10A and voltage drops of 10V, 50V, and 70V, what are the branch resistances and total circuit values?
R1=1Ω, R2=5Ω, R3=7Ω, VT=130V, RT=13Ω, and IT=10A.
In the parallel circuit practice example with 110V across 3Ω, 1Ω, and 12Ω branches, what are the branch currents and total values?
I1=36.67A, I2=110A, I3=9.17A, IT=155.83A, RT≈0.706Ω, and VT=110V.
What are conductors, insulators, and semiconductors, and what examples are given for each?
Conductors have many free electrons and allow current flow (copper, gold, other metals, and water with dissolved mineral impurities). Insulators have few free electrons and resist current flow (rubber, plastic, glass, ceramic, and wood). Semiconductors have properties between conductors and insulators (silicon, germanium, and diamond).
How does a capacitor differ from a battery in how it handles electric charge?
A battery uses a chemical reaction to produce an electric potential and stores charge for later use, whereas a capacitor stores electric charge temporarily and does not produce new electrons.
What is the function of a diode / solid-state rectifier in an x-ray circuit?
It allows current to flow in only one direction; rectifier banks convert alternating current (AC) into direct current (DC) for the x-ray tube.
How do fuses and circuit breakers differ in their method of circuit protection?
A fuse contains a protective wire that melts and permanently opens the circuit if current is excessive, whereas a circuit breaker is a protective switch that trips open when current becomes excessive and can be reset.
What is a rheostat and how is it used in the x-ray machine?
A rheostat is an adjustable resistor used to limit or regulate current; it serves as the mA selector to control filament current.
What is the purpose of grounding in electrical equipment, and to what is the grounding wire attached?
Grounding connects equipment to Earth through a conductor, providing a protective path for fault current and neutralizing charge; the grounding wire connects to non-current-carrying metal parts, such as the housing.
What direction do magnetic field lines travel outside a magnet, and what unit measures magnetic field strength?
Magnetic field lines (flux) travel from north to south outside a magnet and form closed loops; magnetic field strength is measured in tesla (T).
How are magnetic materials categorized, and what constitutes a magnetic domain?
Materials are categorized as ferromagnetic (strong attraction; iron, cobalt, nickel), paramagnetic (weak attraction), diamagnetic (weak repulsion), or nonmagnetic. Magnetic domains are groups of aligned atomic magnetic dipoles.
What is electromagnetism, and what three factors increase induced voltage?
Electromagnetism refers to the relationship where moving electric charge creates a magnetic field, and a changing magnetic field creates current. Induced voltage increases with stronger magnetic fields, faster relative movement, and a greater number of coil turns.
What is the difference between mutual induction and self-induction?
Mutual induction occurs when changing current in a primary coil creates changing flux that induces voltage in an independent secondary coil (used in step-up/step-down transformers). Self-induction occurs when changing current in a coil induces an opposing voltage in that same coil (used in autotransformers).
What is Lenz's law?
Lenz's law states that an induced current or voltage acts in a direction opposing the change that created it.
What energy transformations occur in electric generators and electric motors?
A generator converts mechanical energy into electrical energy by moving a conductor through a magnetic field; an electric motor converts electrical energy into mechanical energy by magnetic interaction (such as the induction motor rotating the anode).
How do step-up and step-down transformers alter voltage and current?
A step-up transformer raises voltage and lowers current, whereas a step-down transformer lowers voltage and raises current; voltage and current change inversely.
What are the ideal transformer formulas relating primary (p) and secondary (s) turns (N), voltage (V), and current (I)?
VpVs=NpNs, IpIs=NsNp, and IpIs=VsVp.
In the textbook transformer example with 10 primary turns, 50 secondary turns, 110V input, and 5A primary current, what are the output voltage and secondary current?
The output voltage is 550V and the secondary current is 1A.
What is an autotransformer, and what controls it in the x-ray circuit?
An autotransformer consists of one tapped coil acting as both primary and secondary using self-induction; it is controlled by the kVp selector to set the voltage delivered to the step-up transformer.
Which components make up the primary circuit of an x-ray system?
The main power switch, circuit breakers, autotransformer, exposure timer, and the primary side of the step-up transformer.
Which components make up the secondary circuit of an x-ray system?
The secondary side of the step-up transformer, milliampere meter, rectifier bank, and the x-ray tube (excluding the filaments).
Which components make up the filament circuit of an x-ray system?
The rheostat (mA selector), step-down transformer, and selected filament(s).
What is the function of the line compensator in the primary circuit?
It adjusts incoming power to the required level (typically described as adjusting incoming power to a standard 220V supply).
How does an automatic exposure control (AEC) system terminate an exposure?
It uses an ionization chamber located between the patient and image receptor; radiation passing into the chamber causes ionization, and when a preset amount of ionization is reached, it signals exposure termination.
What is the functional difference between half-wave rectification and full-wave rectification?
Half-wave rectification uses a single diode and allows only one half-cycle of alternating current to pass, whereas full-wave rectification uses four rectifiers to utilize both halves of the AC cycle.
How do three-phase and high-frequency generator waveforms compare to single-phase waveforms?
Three-phase power reduces voltage ripple compared with single-phase power; high-frequency generators reduce voltage ripple even further, supplying a more nearly constant tube voltage.
What physical process occurs at the cathode filament when heated, and what setting does the selected filament determine?
Heating the filament causes the emission of electrons via thermionic emission to form an electron cloud; the selected filament determines the large or small focal-spot option.
What sequence of events occurs along the primary and secondary electrical pathway during an exposure?
Incoming power passes through the main switch and protection devices; the autotransformer supplies the voltage selected by the kVp selector to the step-up transformer; the step-up transformer raises the voltage to kilovoltage; rectifiers convert AC to unidirectional power; and high voltage creates a positive anode and negative cathode to accelerate electrons across the tube.
What sequence of events occurs along the filament pathway during an exposure?
Power from the autotransformer passes through the rheostat (regulated by the mA selector); the step-down transformer lowers voltage and raises current; current heats the filament to produce electrons by thermionic emission; and the high potential difference accelerates these electrons to the anode target to produce x-rays and heat.
What x-ray beam characteristics do the operator controls (kVp, mA, exposure time, focal spot, and AEC) regulate?
kVp changes accelerating voltage and electron energy (affecting beam penetration); mA changes filament heating and tube current; exposure time controls current duration (mAs=mA×seconds governs total radiation quantity); focal-spot selection selects the filament size; and AEC terminates the exposure when a preset amount of radiation is detected.