1/84
Looks like no tags are added yet.
Exp 1: Agar media used for E. coli
LB agar
Exp 1: Agar media used for L. reuteri
MRS agar
Exp 1: Starting concentration of E. coli
~10^9 CFU/ml
Exp 1: Starting concentration of L. reuteri (and conversion to CFU/ml)
~10^4 CFU/µl = 10^7 CFU/ml
Exp 1: Volume and countable range for spread plating
100 µl (0.1 ml); 30-300 CFU
Exp 1: Volume and countable range for spot plating
Three 10 µl drops; 3-30 CFU per spot
Exp 1: Why change pipette tips during serial dilutions?
To prevent carrying concentrated bacteria into lower dilutions (which overestimates counts)
Exp 1: Why can you reuse the same tip when plating from 10^-7 to 10^-5?
Negligible cells carried over from a 10x more dilute tube won't affect a 10x more concentrated tube
Exp 1: Why dry spread/spot plates near a flame before inverting?
So liquid evaporates completely and colonies don't smear; inverting stops lid condensation from dripping
Exp 1: Formula to calculate CFU/ml from a spot plate
(Average CFU per spot) / (Dilution factor × 0.01 ml)
Exp 2: D-value (Decimal Reduction Time) definition
Time (in minutes) required to kill 90% (1 log10 cycle) of a microbial population at a specific temperature
Exp 2: How to calculate D-value from a survivor graph
D = -1 / slope (when plotting log10 survivors vs. time)
Exp 2: TDT (Thermal Death Time / F-value) definition and formula
Time (in min) to reduce a population to 10^0 (zero): TDT = D × log10(initial population)
Exp 2: F0 value definition
Equivalent time at 250°F (121.1°C) needed to reduce a microbial population to 10^0
Exp 2: Z-value definition
Temperature change (°F or °C) needed to change the D-value or TDT by 1 log10 cycle (10-fold)
Exp 2: D-value vs. Z-value difference
D-value = heat resistance at ONE temperature; Z-value = sensitivity to CHANGES in temperature
Exp 2: Food components that INCREASE microbial heat resistance (higher D-value)
Low water content (water activity), high fat, and high protein
Exp 2: Food additives that DECREASE microbial heat resistance (lower D-value)
Salt and acid
Exp 2: Three temperatures tested in Exp 2
55°C, 60°C, and 65°C
Exp 2: Six time points sampled in Exp 2
0, 2, 5, 10, 15, and 20 minutes
Exp 2: Why add water to heating block wells and cool tubes on ice immediately?
Water improves heat transfer into the tube; ice rapidly stops thermal killing
Exp 2: Why include only ONE 0 CFU/ml data point in the D-value regression graph?
Multiple trailing zeros artificially flatten the slope and skew the D-value
Exp 3: Ratio used to make 1X preservative samples from 10X stocks
1 ml of 10X preservative stock + 9 ml homogenized food (100 g/L) = 10 ml total
Exp 3: Purpose of the PBS control tube in Exp 3
Accounts for the 10% volume dilution (9 ml food + 1 ml PBS) with no preservative added
Exp 3: Final 1X concentrations of all 7 preservatives in Exp 3
3% NaCl, 1.5% citric acid, 1% & 0.1% sodium benzoate, 0.1% potassium sorbate, 200 ppm sodium nitrate, 6.5% sugar
Exp 3: Two agar media and incubation conditions used in Exp 3
Nutrient Agar (bacteria) and Yeast & Mold agar (fungi), incubated at 30°C for 48 hours
Exp 3: Why does yogurt (pH 4.6) still spoil, and what indicates yeast growth?
Low pH inhibits bacteria, but yeasts/molds still grow; lid doming indicates gas from yeast fermentation
Exp 3: Five factors required for mold growth
Oxygen, high moisture, temperature, pH, and nutrients
Exp 3: How to convert CFU/ml to CFU/g in Exp 3
Multiply CFU/ml by 10 (since food was homogenized at 100 g/L = 0.1 g/ml)
Exp 4: Microbial vs. non-microbial factors affecting shelf life
Microbial: water activity, pH, storage temp, handling. Non-microbial: moisture, light, chemical changes, tampering, pests
Exp 4: Direct vs. indirect shelf-life study
Direct = real-time normal storage conditions; Indirect = accelerated harsher conditions or modeling
Exp 4: What is ARISA?
Automated Ribosomal Intergenic Spacer Analysis (molecular method to identify food microbes to species level)
Exp 4: Storage temperatures and sampling days for raw & pasteurized milk
4°C and 22°C/25°C; sampled on Days 0, 2, 4, and 7
Exp 4: Agar media and incubation conditions for milk shelf life
Nutrient Agar (total microbes, 30°C for 48 h) and MacConkey agar (coliforms, 37°C for 24 h)
Exp 4: Why does milk spoil so quickly?
Nutrient-rich composition and near-neutral pH
Exp 4: What does "
0 colonies observed; below the detection limit of 100 CFU/ml
Exp 5: Why are antibiotic residues in milk a problem?
Public health risks and inhibition of beneficial lactic acid bacteria (L. casei, L. lactis) in dairy fermentations
Exp 5: How do β-lactam antibiotics work, and what are 4 examples?
Inhibit bacterial cell wall synthesis; penicillin, ampicillin, amoxicillin, cephalosporin
Exp 5: FDA antibiotic withdrawal period and milk testing rules
Cows cannot receive antibiotics for 48 hours before milking; all farm-to-factory milk must be tested
Exp 5: Indicator organism used in Delvo-P and Charm BSDA tests
Bacillus stearothermophilus
Exp 5: Delvo-P test color results (negative vs. positive)
Purple -> Yellow = Negative (bacteria grew and made acid); Stays Purple = Positive (antibiotic inhibited growth)
Exp 5: Charm BSDA positive control requirement
0.010 mg/ml penicillin must produce a 16-20 mm zone of inhibition
Exp 5: BSDA result: No zone around untreated milk
Negative for inhibitory substances
Exp 5: BSDA result: Zone around untreated milk, NO zone around penicillinase-treated milk
Positive for β-lactam residue (penicillinase degraded the β-lactam)
Exp 5: BSDA result: Equal-sized clear zones around both untreated and penicillinase-treated discs
Positive for non-β-lactam inhibitor(s)
Exp 5: BSDA result: Zone around penicillinase-treated milk is ≥4 mm smaller than untreated milk
Positive for BOTH β-lactam residue and another inhibitor
Exp 5: Indicator organism, agar, and incubation used in our class antibiotic assay
Lactococcus lactis MG1363 on GM17 agar, incubated at 30°C for 24 hours
Exp 5: Why include the β+PM+A control disc?
Positive enzyme control proving that the β-lactamase actively degrades penicillin
Exp 6: Key cellular and growth traits of Listeria
Small, Gram-positive, catalase-positive, non-spore-forming rods; psychrotrophic (grows at 4°C)
Exp 6: Only human-pathogenic Listeria species and fatality rate
Listeria monocytogenes; 20-30% fatality rate (causes meningitis, bacteremia, fetal abortion)
Exp 6: High-risk foods for Listeria and treatments that kill it
Soft cheeses, milk, ready-to-eat meats; eliminated by pasteurization and irradiation
Exp 6: How L. monocytogenes survives inside the host
Induces macrophage phagocytosis, escapes phagolysosome into cytosol, spreads cell-to-cell; cleared by cell-mediated immunity
Exp 6: Selective agents in Listeria Enrichment Broth (EB)
Acriflavin, nalidixic acid, and cycloheximide (incubated at 30°C for 2 days)
Exp 6: Listeria appearance and incubation on PALCAM agar
Black colonies with black halos (esculin hydrolysis); incubated at 35°C for 24-48 hours
Exp 6: Listeria appearance and illumination on LPM agar
Sparkling bluish ("crushed glass") colonies under Henry illumination (45° incident light, 90° viewing angle)
Exp 6: Why purify colonies on TSAYE, and what do typical colonies look like?
Removes invisible background competitors; 1-3 mm, smooth, convex, white colonies (incubated 30°C, 24-48 h)
Exp 6: Catalase test reagent and positive result for Listeria
3% H2O2; bubbling (O2 gas) = positive
Exp 6: Blood agar hemolysis results for L. monocytogenes vs. L. innocua
L. monocytogenes & L. ivanovii = narrow β-hemolysis clearing (+); L. innocua = no clearing (-) (35°C, 48 h)
Exp 7: Principle of the LST-MUG assay
Coliforms ferment lactose to gas; E. coli's β-glucuronidase (GUD) cleaves MUG to 4-methylumbelliferone (MU), which fluoresces blue under 365 nm UV
Exp 7: LST-MUG incubation conditions and confirmation medium
35°C for 24 ± 2 hours; confirmed by streaking fluorescent tubes onto L-EMB agar (35°C, 24 ± 2 h)
Exp 7: Four media used to isolate diverse meat bacteria for Exp 8
MRS, BHI, NA, and MAC (incubated at 37°C for 24 hours)
Exp 7: Indole test medium, reagent, and positive result
Tryptone broth + Kovac's reagent -> red ring at the top interface
Exp 7: Methyl Red (MR) test colors and pH meanings
Red/pink (pH ≤ 4.4) = mixed-acid fermentation (+); Yellow (pH ≥ 6.2) = butanediol fermentation (-); Orange = equivocal
Exp 7: Voges-Proskauer (VP) reagents and positive result
12 drops α-naphthol + 4 drops 40% KOH (read in 10-30 min) -> red color (detects acetoin)
Exp 7: Simmons Citrate slant positive result
Medium turns blue (alkaline reaction from citrate utilization)
Exp 7: Diagnostic IMViC patterns for E. coli
++-- (Biotype 1) or -+-- (Biotype 2)
Exp 8: Bacterial 16S rRNA gene regions and amplicon size in class
~1542 bp total; conserved regions (C1-C9) bind universal primers, variable regions (V1-V9) identify genus/species; class amplifies V3-V4 (~550 bp)
Exp 8: Two 16S sequence databases mentioned in Exp 8
NCBI (BLAST) and Ribosomal Database Project (RDP)
Exp 8: Why microwave Gram-positive colonies (e.g., Staphylococcus) for 1 min before PCR?
Thick peptidoglycan cell walls resist standard 95°C PCR lysis; microwaving breaks open cells to release DNA
Exp 8: Final concentration of each primer in the 50 µl PCR mix
0.4 µM (10 µl of 2 µM primer diluted into 50 µl total volume)
Exp 8: PCR thermocycler temperatures and steps
95°C 5 min; 30 cycles of [95°C 30 s, 55°C 30 s, 72°C 30 s]; final extension 72°C 2 min; hold 4°C
Exp 8: Two functions of DNA loading dye
Bromophenol blue tracks DNA migration; glycerol/sucrose adds density so DNA sinks into the well
Exp 8: Crucial pipetting rule when loading an agarose gel
Load at a 45° angle and DO NOT release the plunger until the tip is completely out of the well
Exp 8: How higher agarose percentage (2.5% vs. 0.5%) affects DNA migration
Creates smaller pores, slowing DNA migration and better separating smaller DNA fragments
Exp 8: How Ethidium Bromide (EtBr) works and its safety hazard
Intercalates between dsDNA bases to fluoresce under UV; hazardous mutagen (wear gloves and UV shield)
Exp 8: Why spin the empty GeneJET column before eluting DNA?
Removes residual ethanol from wash buffer, which would inhibit downstream Sanger sequencing
Exp 8: Why use Qubit fluorometer instead of NanoDrop to quantify DNA?
Qubit uses a DNA-specific fluorescent dye, whereas NanoDrop measures total nucleic acids (including contaminating RNA)
Exp 8: Target DNA concentration and volume for Sanger sequencing
3 ng/µl in at least 20 µl final volume (using C1V1 = C2V2)
Exp 8: Sequencing primer calculation (25 pmol needed from 5 µM working stock)
1 µM = 1 pmol/µl, so 5 µM = 5 pmol/µl; add 5 µl to get 25 pmol (more accurate than 0.5 µl of 50 µM stock)
Exp 9: Lytic vs. lysogenic bacteriophage cycles
Lytic = infects, replicates, and lyses host bacteria immediately; Lysogenic = phage DNA integrates dormant into host chromosome
Exp 9: How mitomycin C induces lysogenic bacteriophages
Damages bacterial DNA (0.2 µg/ml), triggering prophage excision, replication, and cell lysis (OD drops at 5-7 h)
Exp 9: Role of CaCl2 in the plaque assay
Helps bacteriophages adsorb (attach) to bacterial host cells
Exp 9: Why are plaque assay plates NOT inverted during 30°C incubation?
0.4% soft top agar stays semi-soft and would slide/flow onto the lid if inverted
Exp 9: Why measure phage titer in PFU/ml instead of virions/ml?
Only infectious phage particles form visible plaques (30-300 countable range)
Exp 9: Mechanism of quark formation and how phage affects sensitive vs. resistant strains
L. lactis ferments lactose to lactic acid (pH ~4.6), precipitating casein to thicken milk. Resistant strain makes quark ± phage (no plaques); sensitive strain fails to acidify/thicken milk when phage is present (forms plaques)