1/29
Comprehensive practice flashcards covering semiconductor characteristics, thyristor operations, triggering methods, commutation types, and device protection methods from the Power Electronics lecture notes.
What is the definition of Power Electronics according to the lecture notes?
Power Electronics is the branch of Electronics that tells how power is used and utilised.
What are the two primary reasons for using a power diode instead of a low-power diode?
1) To handle maximum power, and 2) to stop breakdown or increase breakdown voltage.
What are the doping concentrations of the cathode substrate, drift region, and anode in a power diode?
The cathode (n+ substrate) has a doping level of 1019/cm3, the lightly doped drift region (n− layer) has a doping level of about 1014/cm3, and the diffused anode (p+ region) has a doping level of 1019/cm3.
What factor determines the breakdown voltage of a power diode?
The thickness of the lightly doped n− drift region.
How does conductivity modulation occur in the drift layer of a forward-biased power diode?
Under forward bias, holes injected from the p+ region into the n− drift region attract electrons from the n+ region. Simultaneous injection of holes and electrons drastically reduces the drift region resistance, allowing current to rise significantly.
What is defined as the reverse recovery time of a power diode?
The time required for stored minority charge carriers (holes and electrons) in the PN junction and bulk semiconductor material to recombine with opposite charges and neutralize upon sudden polarity reversal.
What are the operating ranges and reverse recovery times of General Purpose, Fast Recovery, and Schottky diodes?
General Purpose: 5000V, 3500A, and 20−30μs; Fast Recovery: 3000V, 1000A, and 2−5μs; Schottky: 100V, 300A, and extremely low (a few nanoseconds).
What is the cut-in voltage (or knee voltage) of a power diode?
The forward voltage at which current through the diode increases very rapidly after the external voltage overcomes the internal potential barrier.
Why does a power BJT utilize a vertically oriented four-layer structure?
It maximizes the cross-sectional area through which device current flows, minimizing on-state resistance and device power dissipation.
What are the junction bias conditions for a power BJT operating in the cut-off, active, and saturation regions?
Cut-off: both EB and CB junctions are reverse biased (OFF switch); Active: EB junction is forward biased and CB junction is reverse biased (amplifier); Quasi and Hard Saturation: both EB and CB junctions are forward biased (closed/ON switch).
How does the quasi-saturation region of a power BJT differ from the hard saturation region?
Quasi-saturation occurs due to the lightly doped n− drift layer and does not push the BJT into deep saturation, enabling faster turn-off; hard saturation minimizes voltage drop and power dissipation, but requires a longer time to turn off.
What are the differences between a Power BJT and a Power MOSFET regarding control type, carrier type, and temperature coefficient?
A Power BJT is a current-controlled, bipolar device with a negative temperature coefficient, whereas a Power MOSFET is a voltage-controlled, unipolar device with a positive temperature coefficient.
Why is an n-channel enhancement Power MOSFET more commonly used than a p-channel enhancement MOSFET?
Because of the higher mobility of electrons compared to holes.
What combined features make the IGBT advantageous, and what are its typical ratings?
The IGBT combines the high input impedance of a MOSFET with the low on-state conduction losses of a BJT; single devices can achieve ratings up to 400A, 1200V, and switching frequencies up to 20kHz.
What is the physical structure of a Silicon Controlled Rectifier (SCR)?
A vertically oriented four-layer structure (p+−n−−p/p+−n+) forming three junctions (J1,J2,J3) and three external terminals: Anode (A), Cathode (K), and Gate (G).
What are the bias states of junctions J1, J2, and J3 when an SCR is in forward blocking mode?
Junctions J1 and J3 are forward biased, while junction J2 is reverse biased, preventing bulk conduction and permitting only a small leakage current.
What condition causes turn-on in the two-transistor analogy of an SCR?
When the sum of the common-base current gains reaches unity (α1+α2=1), the denominator in IA=1−(α1+α2)α2IG+ICBO1+ICBO2 approaches zero, causing regenerative current flow that latches the device ON.
What is the difference between latching current (IL) and holding current (IH) in an SCR?
Latching current is the minimum anode current required to transition and latch the SCR into the ON state during turn-on; holding current is the minimum anode current required to maintain the SCR in the ON state before it turns OFF.
Why is forward voltage triggering never used in practical SCR circuits?
Applying voltage up to the forward breakover voltage (VBO) induces avalanche breakdown of junction J2; the continuous flow of huge currents at high voltages can destroy the junction and permanently damage the device.
How does dv/dt triggering occur in an SCR?
The reverse-biased junction J2 acts as a capacitor with charging current ic=Cdtdv. If the rate of rise of voltage is steep, the resulting transient current acts like a gate current, turning on the SCR prematurely.
How does light triggering turn on a Light-Activated SCR (LASCR)?
A beam of light of appropriate wavelength and frequency shines on the inner p-layer, generating electron-hole pairs that inject free carriers into junction J2, turning the thyristor ON.
What is the firing angle range limitation of an SCR resistance (R) triggering circuit?
The firing angle can only vary over a limited range of 0∘ to 90∘.
What is the function of the diode placed in the gate path of an R-triggering circuit?
It prevents the reverse voltage across the thyristor gate from exceeding the peak reverse voltage limit during the negative half-cycle.
How does an RC triggering circuit improve firing control compared to a simple R triggering circuit?
The capacitor provides a phase shift that extends the controllable firing angle beyond 90∘ up to nearly 180∘.
How is the thyristor turned off in Class A (self/load) commutation?
An underdamped resonant L-C-R load circuit causes the conducting current to naturally oscillate back to zero and reverse polarity, commutating the thyristor off.
How does Class C (complementary) commutation turn off the main SCR (T1)?
When the auxiliary SCR (TA) is triggered, a previously charged capacitor applies a reverse voltage across T1, driving reverse current through it and forcing it to turn off.
How do circuit breakers and fast-acting fuses differ in SCR overcurrent protection?
Circuit breakers protect against sustained fault currents or surges of large duration due to their longer tripping times, whereas fast-acting/current-limiting fuses protect against high surge currents of very short duration.
What are the common internal and external causes of overvoltage across a thyristor?
Internal causes: reverse recovery current transients during commutation producing large Ldtdi spikes; External causes: interruption of inductive circuits, lightning strikes, and switching transients on the transformer primary.
What two types of protection does an RC snubber circuit provide when placed across an SCR?
It provides overvoltage protection (by suppressing reverse-recovery voltage spikes) and dv/dt protection (by limiting the rate of voltage rise).
How does a varistor protect a thyristor from overvoltage?
A varistor is a non-linear clamping resistor whose resistance sharply decreases as voltage exceeds a specific threshold, clamping transient overvoltages across the device.