1/67
Looks like no tags are added yet.
In passing through the material, which two things may happen to the X-rays and gamma radiation?
Transmitted or absorbed
Three items that directly affect geometric unsharpness when using film radiography are
Object to film distance, source to film distance and source size
Radiation that is transmitted completely through a material will produce
The radiographic image
Radiographic film images showing a lighter area on the image indicate
Less radiation reaching the film due to thicker areas of the part
Radiographic film images showing a darker area on the image indicates
More radiation reaching the film due to thinner areas of the part
The term attenuation is the same as _?of radiation
Absorption
Geometric un-sharpness is what type of shadow?
Penumbra
Geometric unsharpness can be reduced by
A small source size, large distance from the source and small distance of the test object to the film/imaging plate
Discontinuity enlargement occurs
When the discontinuity is farthest from the film/imaging plate
The principle of geometric unsharpness is that
The farther the distance between the test object and the film, with the source in the same position, the greater the penumbral shadow
Optimum geometrical image sharpness in film radiography is obtained with a combination of a
Smaller source, greater distance between the source and the test object, and a shorter distance between the test object and the film
Three forms of radiation scatter are
Internal, side and back
Internal scatter radiation is commonly reduced or eliminated by the use of
Lead Screens
Gamma rays are generated by which of the following?
Radioactive isotopes undergoing disintegration
The most widely used standard (imperial) unit of measurement for measuring the rate at which the output of a gamma ray source decays is the
Curie
A gamma ray source is designated as Iridium-192. The 192 designation is the
Mass number
The activity of a gamma ray source is measured in
Curies in the US system and Becquerels in the SI system
Which of the gamma ray sources listed below has an energy greater than 1 million electron volts?
Cobalt 60
Natural and artificial radioisotopes disintegrate by releasing energy in the following forms:
Gamma rays, Beta particles, Alpha particles
Gamma ray intensity is
A measure of amount (quantity) of radiation emission
A half life is the time it takes for
The activity of an isotope to decay to 1/2 of its initial strength
A typical atom generally consists of all of the following except
Negatively charged neutrons
The following radioactive isotope is produced in neutron activation
Iridium 192
Radiographic testing images are typically
Digital images or film images
Advantages of radiographic testing include
Can be used on most materials and can reveal discontinuities within a material
Radiographic testing uses X-ray and gamma ray sources that generate great amounts of radiation that can cause
Damage to cells of living tissue, which is a health hazard
The spontaneous decay process "radioactivity" was discovered by
Marie Curie
A number raised to the power of 0 (excluding 0 itself) is always
1
Which of the following is an advantage of radiographic testing?
Can reveal discontinuities open to the surface and can reveal discontinues within the material
Three basic principles to minimize radiation exposure are
Time, distance and shielding
How many different levels of qualification currently exist in the radiographic testing industry?
3
X-rays and gamma rays have each of the following characteristics except
Have an electrical charge and large mass
X-rays and gamma rays overlap on the
Electromagnetic spectrum
X-rays are generated when __________ interact with matter.
High energy electrons
The target in an x-ray tube is located in the
Anode
The filament is the source of free electrons in an x-ray tube head and is located in the
Cathode
The intensity of the X-ray or gamma ray beam varies inversely with the square of the distance from the radiation source. This principle is referred to as the
Inverse square law
While using an x-ray tube for radiography, the operator wants to increase the radiation intensity. What should be done?
Tube current should be increased
The most commonly used target material in an x-ray tube is
Tungsten
The ability of a material to block or partially block the passage of X-rays and gamma rays is called
Absorption
When a radiograph is viewed, which area provides the least radiographic film density?
The thickest area with no voids
Which of the following is not a characteristic of X and gamma rays?
They resist absorption by matter
X-rays are created when
Rapidly moving electrons interact with matter
Which side of an x-ray tube has a positive charge?
Anode side
With other variables unchanged, an increase in kilo voltage (kV) of an x-ray machine will generate
High intensity hard x-rays
The inverse square law states that the
Intensity of an x-ray beam is inversely proportional to the square of the distance to the radiation source
X-ray equipment has three basic requirements for generating x-rays. What are they?
Source of free electrons, Means of moving the electrons rapidly in a desired direction, A suitable material for the electrons to strike
An x-ray tube contains a vacuum sealed envelope, which in turn contains
The cathode and anode
The filament of an x-ray tube that generates free electrons is located in the
Cathode
The target that free electrons strike to generate x-rays in an x-ray tube is located in the
Anode
The focusing cup in an x-ray tube performs what function?
Act as an electrostatic lens that directs the electrons in a beam towards the anode
The filament of an x-ray tube is usually a coil of what type of material that can withstand high temperature?
Tungsten
Why is a high vacuum required in an x-ray tube?
It prevents oxidation of the electrode material, It provides electrical insulation between the electrodes, It permits electron passage without ionization of gas in the tube
The major limitation in making a very small focal spot in an x-ray tube is
The heat generated in target bombardment
X-ray energy above 500 keV cannot be obtained with which type of x-ray machine?
Typical portable x-ray unit
The electron emitting portion of an x-ray tube is the
Filament
The intensity of x-rays can be increased by increasing the
Milliamperes
While an x-ray machine is on and in an operating mode, most of the energy of the electron beam is
Expended in heat
The penetrating ability of an x-ray machine is increased by applying
Increased kilo voltage
The phenomenon known as the "heel effect" creates a beam intensity that
Decreases from the central ray toward the anode side and increases from the central ray toward the cathode
Which of the following materials are used inside an ANSI category 1 exposure device to shield the operator from gamma rays during transport?
Depleted uranium
Compared to the effective focal spot in x-ray machine, the actual focal spot is
The area struck by electrons
Which of the following is an x-ray generator that operates on an electrostatic principle to accelerate electrons?
Van de graaff accelerator
Which of the following is a distinguishing feature of an ANSI category 2 exposure device that sets it apart from a category 1 device?
A rotating cylinder
A tube that carries the source from the shielded position in an exposure device to the place where the radiographic exposure is made is called a
Guide tube
The on-off switch of a Type 2 exposure device is used to
Indicate the position of the source within the cylinder
Which of the following are ionization processes?
Photoelectric effect, Compton effect, Pair production
Which of the following ionization processes of X or gamma rays is more likely with a low energy photon and material with a high atomic number?
Photoelectric absorption