1/47
Comprehensive vocabulary flashcards covering key definitions, units, scientific laws, and biological concepts across Electricity, Reproduction, Metals and Non-Metals, and Optics.
Electric Current
The rate of flow of electric charges through a conductor, expressed as the amount of charge flowing through a particular area in unit time: I=tQ.
Electric Circuit
A continuous and closed path along which an electric current flows.
Ampere (A)
The SI unit of electric current, defined as the flow of one coulomb of charge per second (1A=1C/1s).
Electric Potential Difference (V)
The work done to move a unit charge from one point to another in a current-carrying conductor: V=QW.
Volt (V)
The SI unit of electric potential difference, defined as the potential difference between two points when 1joule of work is done to move a charge of 1coulomb (1V=1JC−1).
Ohm's Law
The principle stating that the potential difference across the ends of a given metallic wire in an electric circuit is directly proportional to the current flowing through it, provided its temperature remains the same (V=IR).
Electrical Resistance (R)
The property of a conductor to resist the flow of charges through it, mathematically given by R=IV and measured in ohms (Ω).
Electrical Resistivity (ρ)
A characteristic material constant of proportionality relating resistance to length and cross-sectional area (R=ρAl), measured in Ωm.
Joule's Law of Heating
The law stating that the heat produced in a resistor is directly proportional to the square of the current, the resistance, and the time for which current flows (H=I2Rt).
Electric Power (P)
The rate at which electric energy is dissipated or consumed in an electric circuit, given by P=VI=I2R=RV2 and measured in watts (W).
Kilowatt Hour (kWh)
The commercial unit of electrical energy, representing the energy consumed when 1000watts of power is used for 1hour, equal to 3.6×106J.
Binary Fission
A form of asexual reproduction in unicellular organisms where a single mature cell splits into two equal halves (e.g., in Amoeba and Leishmania).
Multiple Fission
A mode of asexual reproduction where a single-celled organism divides into many daughter cells simultaneously (e.g., in Plasmodium).
Fragmentation
An asexual reproductive method in multi-cellular organisms with simple body design where the organism breaks into smaller pieces upon maturation, each piece growing into a new individual (e.g., in Spirogyra).
Regeneration
The ability of fully differentiated organisms to give rise to complete new individual organisms from cut or broken body parts via specialised proliferating cells (e.g., in Hydra and Planaria).
Budding
An asexual mode of reproduction where a bud develops as an outgrowth due to repeated cell division at one specific site, maturing and detaching from the parent body (e.g., in Hydra and yeast).
Vegetative Propagation
A mode of plant reproduction in which vegetative parts such as the root, stem, or leaves develop into new individual plants under appropriate conditions.
Tissue Culture
A technique of growing new plants by removing tissue or cells from the growing tip, placing them in an artificial medium to form a callus, and transferring them to a hormone medium for differentiation.
Pollination
The process of transferring pollen grains from the anther of a stamen to the receptive stigma of a pistil, categorized as self-pollination or cross-pollination.
Puberty
The period during adolescence when general body growth slows down and reproductive tissues begin to mature, signaling sexual maturation.
Placenta
A special disc-shaped tissue embedded in the uterine wall containing villi that provides a large surface area for glucose, oxygen, and waste transfer between the mother's blood and the embryo.
Menstruation
The monthly breakdown and vaginal shedding of the unneeded thick, spongy blood-rich uterine lining and unfertilized egg, lasting about two to eight days.
Metallic Lustre
The characteristic physical property of metals in their pure state possessing a shining, polished surface.
Malleability
The property of metals that allows them to be beaten or hammered into thin sheets without shattering (gold and silver being the most malleable).
Ductility
The physical ability of a metal to be drawn into thin wires (gold being the most ductile metal).
Sonorous
The physical property of metals that cause them to produce a ringing sound when struck against a hard surface.
Amphoteric Oxides
Metal oxides that react with both acids and bases to produce salts and water (e.g., aluminium oxide, Al2O3, and zinc oxide, ZnO).
Anodising
The industrial process of forming a thick, protective, corrosion-resistant oxide layer on aluminium by making it the anode during electrolysis with dilute sulphuric acid.
Reactivity Series
A vertical arrangement of metals placed in the order of their decreasing chemical reactivities.
Ionic Compounds
Compounds formed by the transfer of valence electrons from a metal to a non-metal, held together as aggregates by strong electrostatic forces of attraction.
Roasting
The metallurgical process of converting sulphide ores into metal oxides by heating them strongly in the presence of excess air.
Calcination
The metallurgical process of converting carbonate ores into metal oxides by heating them strongly in limited air.
Thermit Reaction
The highly exothermic reduction of iron(III) oxide by aluminium (Fe2O3+2Al→2Fe+Al2O3+Heat), producing molten iron used to weld railway tracks or cracked machine parts.
Gangue
The unwanted earthly impurities, including soil, sand, and rocky debris, that naturally contaminate mined ores.
Galvanisation
A protective method used to prevent the rusting of iron and steel by coating them with a thin layer of zinc.
Aqua Regia
A freshly prepared, fuming, highly corrosive mixture of concentrated hydrochloric acid and concentrated nitric acid in a volume ratio of 3:1, capable of dissolving noble metals like gold and platinum.
Alloy
A homogeneous mixture composed of two or more metals, or a metal and a non-metal, manufactured to achieve desired material properties.
Diffraction of Light
The phenomenon in which light bends around the edge of an opaque object that is extremely small, deviating from strict straight-line ray propagation.
Principal Focus (F)
The point on the principal axis where rays of light travelling parallel to the principal axis either converge (concave mirror/convex lens) or appear to diverge from (convex mirror/concave lens) after reflection or refraction.
Focal Length (f)
The distance between the pole (or optical centre) and the principal focus of a spherical mirror or lens.
Aperture
The diameter of the circular outline representing the effective reflecting surface of a spherical mirror or refracting surface of a spherical lens.
Mirror Formula
The mathematical relationship relating object distance (u), image distance (v), and focal length (f) for spherical mirrors: v1+u1=f1.
Magnification (m)
The ratio of the height of the image (h′) to the height of the object (h), represented as m=hh′=−uv for mirrors, and m=hh′=uv for lenses.
Refraction of Light
The change in the direction of propagation of a light ray as it enters obliquely from one transparent medium to another due to a difference in light speed across the media.
Snell's Law of Refraction
The law stating that the ratio of the sine of the angle of incidence to the sine of the angle of refraction is constant for light of a given colour and a given pair of media: sin(r)sin(i)=constant.
Absolute Refractive Index
The ratio of the speed of light in vacuum or air (c) to the speed of light in the medium (v): n=vc.
Lens Formula
The mathematical equation expressing the relationship between object distance (u), image distance (v), and focal length (f) for a spherical lens: v1−u1=f1.
Power of a Lens (P)
The degree of convergence or divergence achieved by a lens, defined as the reciprocal of its focal length in metres (P=f1) and measured in dioptres (D).