1/67
Looks like no tags are added yet.
2 parts of evaluation for delivery
eval on the cast (prior to delivery)
eval on the patient
master cast vs sectioned cast
master cast uses sectioned and trimmed single dies —> shows margin of the resto, occlusion
solid cast (poured from the same impression) for proximal contact evaluation
restoration evaluation on cast prior to appointment
proximal contacts/ axial contour
marginal fit
occlusal contact/anatomy
surface/ shade
is it better to be hyper/ hypo-occluded
hyper; hypo must be sent back to the lab. you can modify hyper
in the caser of multiple restorations
try each in independently, then try them in together
what burs can you use to modify ceramic restorations
PPPD( circle polishing burs for glass ceramics and zirconia)
red/yellow band diamond burs (fine/ extra fine)
what are the appropriate burs for modifying metal restor
red/yellow diamond bur
brownie/greenie
try in/ adjust resto steps:
proximal contacts
margin/internal fit — fit checker (internal)
occlusion/anatomy (full coverage resto = before cement, bonded resto = after cement)
MIP
excursive
polish/verify shade
proximal contacts must be evaluated using
shimstock mylar
occlusion should be adjusted to be consistent with
the bite record during final impression/ mounting of the master cast
consistent with MIP or CR (when there is no stable occlusion readily available)
when posterior cuspal height is steeper than anterior guidance
working interferance during excursive movement
presence of a _______ contact is acceptable only in the the case of ______ occlusion
presence of a working side contact is acceptable only in the case of a group function occlusion

the presence of a non-working interferance is
not acceptable
can you have any degree of hyperocclusion
no
hypo-occluded is acceptable up to ______ mylar hold
4
shade match is under what category
surface
when must shade be evaluated and selected
prior to the cementation appointment `
patient must approve shade of the resto ______
prior to faculty evaluation and cementation
ideal properties of cement: tensile strength
high
ideal viscosity of cement
low
should flow easily
you want cement to be radio_____
opaque
water based cements
zinc oxide eugenol
zinc phosphate
polycaroxylate
glass ionomer
resin modified glass ionomer
resin based cement
adhesive resin
ZOE cement is made from what two components
eugenol (liquid acid ) + Zinc oxide powder (base)
zinc phosphate cement
phosphoric acid + zinc oxide
polycarboxylate cement
polyacrylic acid + Zinc oxide cement
glass ionomer cemetn
polyacrylic acid + silica
resin based adhesive bonding
polymerization
micromechanical bonding
acid-base reaction
non adhesive (macro-mechanical)
chemiclal bonding
zinc oxide eugenol disadvantages
high soluability in water
inhibits polymerization - dont use before bonding
low strength (tensile, compressive, abrasion resistance)
how does zinc oxide eugenol work/ what is it used for
macromechanical bonding/ temporary cement (luting cement)
zinc phosphate film thickness
25 microns (low viscosity)
zinc phosphate disadvantages
technique sensitive mixing, water soluable, low pH - irritates the pulp
zinc phosphate used as a
permanent cement (gold standard)
which is the gold standard luting cement
zinc phosphate
luting agent
any material used to attach or ceemnt indirect retorations to prepared teeth
polycarboxylate disadvantages
zinc oxide + polyacrylic acid
short working time
polycarboxylate advantages
low soluability (compared to ZoE)
low viscosity (compared to ZoE)
chemical bonding to tooth structure (similar to GIC)
higher pH compared to Zinc phosphate (low pH may irritate pulp)
polycarboxylate used as a
temporary/ permanent cement
polycarboxylate uses what kind of bonding
chemical
which dental cements work via chemical bonding
polycarboxylate
glass-ionomer
resin-modified glass-ionomer
glass ionomer cement powder components
calcium aluminum fluorosilicate glass
zinc oxide
silver
glass ionomer cement liquid components
polyacrylic-itaconic acid/ polycarboxylic acid solution
tartaric acid
water
GI advantages
bonds to tooth structure (chemical bond)
fluoride releasing
more esthetic
GI disadvantage
moisture sensitive
GI is used as what kind of cement
Permanent
GI mechanism
acid from polyacid component attacks glass —> glass releases Ca2+, Al3+, and F-, Cations cross-link polyacid molecules froming salt matrix
Resin modified GIC components
powder + liquid + reisn
resin components RMGIC
methacrylate polyacid
hydroxyethylmethacryclate
activator/initiators/stabilizers
advantages/ disadvantages of RMGIC
longer working time
stronger than GIC (higher tensile strength/ bond strength)
less sensitive to water
disadvantages : less fluoride release compared to GIC
polycarboxylate + CIG bond
chemical and mechromechanical bond to the TOOTH, macromechanical bond to the RESTORATION
etch and rinse indications
high esthetic demand
proper isolation possible
low strength restorations (feldspathic porcelains, veneers)
preparation in enamel
highly calcified structures
self etch indications
low esthetic demand
isolation difficult
medium strength restorations (lithium disilicate)
prep predominantly in dentin
self adhesive
low esthetic demand
isolation difficult
medium to high strength restorations (lithium disilicate, alumina, zirconia, PFM)
prep predominantly in dentin.
3 bottle step
enamel/ dentin conditioning
primer
adhesive2
2 bottle step
two in one condisioner /primer +adhesive
conditioner + two in one primer / adhesive
1 bottle step
univeral adhesive (scotchbond universal plus) (can be used with etch)
coupling agent between glass ceramic and resin composite
silane
adhesion promotors (glass ceramics)
acid etch: HF acid - creates rought surface of intaglio of resto
silane coupling agent (must be DRYED)
two bottle system
pre-hydrolyzed bottle
adhesion promotors (zirconia, alumina, base metals)
airborne particle abrasion / sand blast
10 MDP
organophosphate ester primer :10- MDP
(tribochemical treatment)
what cement would you use for a long term provisional
polycarboxylate
compromised retention form
adhesive resin
which dental cements need isolation/ moisture control
GIC, RMGIC, Adhesive resin
light cured resin indicated for
translucent restorations less than 2 mm thick
dual/self cured indication
opaque, zirconia, thick, deep cement layer
how do you prepare the substrate
air abrasion (except glass ceramics)
etch - HF
silane
dynamic seating
patient bites down on resto
do not use this method for PFM w porcelain margins
floss contacts while pt maintains apical pressure?
other ways to improve seating of crown
apply cement only to margins
vent
ultrasonic vibration