190103i Hydraulic System Components: Pumps, Valves and Cylinders

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/51

encourage image

There's no tags or description

Looks like no tags are added yet.

52 Terms

1
New cards

A hydraulic gear pump converts _______ energy into __________ energy.

Mechanical into hydraulic

2
New cards

What are the 2 categories of hydraulic pumps?

  • non-positive displacement

  • positive displacement


3
New cards

What is the most important characteristic of a non-positive displacement pump?

The inlet and outlets are connected hydraulically

4
New cards

Most non-positive displacement pumps use ____________ to create flow.

centrifugal force

5
New cards

When pressure builds up on the outlet side of a non-positive displacement pump, what happens to flow?

Liquid will begin to recirculate within the pump, and the amount of flow to the outlet port is reduced

6
New cards

What would a typical example of a non-positive displacement pump be?

A water pump in an engine

7
New cards

What is the greatest advantage a positive displacement pump has over a non-positive displacement pump?

They do not suffer significant flow loss under pressure because the path of flow between the inlet and outlet is mechanically sealed

8
New cards

A hydraulic gear pump creates _________.

Flow

9
New cards

How is pressure created in a hydraulic gear pump?

Pressure is the result of resistance to flow

10
New cards

Define pump displacement

The volume of liquid delivered by the pump when the pump input shaft rotates one revolution

11
New cards

What is the flow rate of a pump?

The amount of liquid a pump delivers in a given period of time

12
New cards

What 2 things is the amount of flow that a hydraulic pump delivers determined by?

  • pump displacement

  • input shaft speed


13
New cards

How do you calculate pump flow rate with imperial units?

Pump Flow Rate (GPM) =

((Pump Displacement in³/rev)(rpm)) / 231 in³/gal

14
New cards

How do you calculate pump flow rate with metric units?

Pump Flow Rate (LPM) =

((Pump Displacement cm³/rev)(rpm)) / 1000 cm³/L

15
New cards

Pump efficiency is determined by what 2 things?

  • mechanical efficiency

  • volumetric efficiency


16
New cards

Define mechanical efficiency

The amount of power required to overcome the pump’s internal friction

17
New cards

Define volumetric efficiency

the amount of flow lost within the pump due to internal leakage

18
New cards

How does internal leakage within a hydraulic gear pump occur?

  • the pump is moving oil from a low pressure area to a high pressure area

  • the oil wants to flow from the outlet back to the inlet

  • there are internal clearances within the pump that prevents contact between its moving components

  • the hydraulic oil leaks from the outlet back to the inlet using these internal clearance paths


19
New cards

Why is some internal leakage necessary for all hydraulic pumps?

Provides lubrication for the pump’s moving parts

20
New cards

What are the 2 basic types of gear pumps?

External gear and internal gear

21
New cards

Why are the gears forced toward the inlet side of a pump on an external gear pump?

High pressure oil acting on the surface area of the gears on the outlet side is opposed by a lower pressure on the inlet side

22
New cards

Gear teeth should be rotating ______ mesh on the outlet side and ________ mesh on the inlet side

Into, out of mesh

23
New cards

Which is larger, pump inlet or pump outlet? Why

Pump inlet - to ensure that adequate oil volume is available at all times

24
New cards

What is an identifiable external feature of a reversible gear pump?

The inlet and outlets are generally the same size

25
New cards

The pressure at the pump inlet port is affected by:


  • the amount of restriction to oil flow in the pump inlet line

  • speed the pump is driven


26
New cards

What can cause more restriction to oil flow in the inlet port?

  • oil viscosity too high

  • reservoir is mounted too far below the pump


27
New cards

What occurs when the supply of oil is insufficient to keep the pump inlet flooded with oil?

Cavitation

  • inlet pressure drops

  • pockets of vaporized hydraulic oil form

  • the bubbles implode when exposed to system pressures on the outlet side of the pump and erode internal surfaces of the pump


28
New cards

How can you prevent cavitation?

  • use correct length and size of inlet line

  • keep reservoir strainer and inlet line free of obstructions

  • flood the inlet side of the pump by locating the reservoir above the pump’s inlet

OR

  • charge the pump’s inlet by using a pressurized reservoir


29
New cards

How does aeration occur?

If the inlet line to the pump is leaking, air enters the pump.

30
New cards

Is a direct-acting pressure relief valve normally open or normally closed?

Normally closed

31
New cards

When a direct-acting pressure relief valve in in its normal position (closed), where does the flow of oil travel?

The flow of oil is blocked from its inlet port to its outlet port

32
New cards

What should you do first when adjusting a normally closed direct-acting pressure relief valve?

refer to the manufacturer’s recommended procedures

33
New cards

Define cracking pressure of a pressure relief valve

The pressure at the inlet port when the ball is initially moved off its seat by hydraulic system pressure

34
New cards

Define full flow pressure in a pressure relief valve

the pressure required to fully open the relief valve

35
New cards

Define pressure override in a pressure relief valve

The pressure difference between cracking pressure and full flow pressure

36
New cards

What are the 3 common types of directional control valves? Which is the most common?

  • poppet type

  • rotary type

  • spool type - most common


37
New cards

What is the function of the poppet directional control valve?

Allows oil to flow in one direction and block the flow in the opposite direction

38
New cards

What are the grooves for on a spool?

They trap oil that leaks through the clearances and ensures a good seal/lubrication of the spool and its bore

39
New cards

What are the metering notches for on a spool?

provides the operator with a greater degree of control over cylinder speed by only letting small amounts of oil flow into the cylinder at a time

40
New cards

What is a detent?

Located in a lever-operated valve that holds the valve in a given position that frees the operator’s hands

41
New cards

Where does oil flow in an open centre directional control valve in neutral?

Oil from the pump can flow through the valve and return to the reservoir

42
New cards

What are the 3 most common method of valve actuation?

  • mechanical (lever or pedal)

  • pilot

  • electrical


43
New cards

Where does oil flow in a closed centre directional control valve in neutral?

It blocks the flow of oil from the pump

44
New cards

A hydraulic cylinder converts _______ power into _______ power.

hydraulic power into mechanical power

45
New cards

A single acting cylinder is hydraulically operated in _______ direction.

Only one

46
New cards

What is required to retract a single-acting hydraulic cylinder rod?

An external force (gravity or spring force)

47
New cards

Double-acting hydraulic cylinders hydraulically ______ and ______.

extend and retract

48
New cards

Extend and retract

49
New cards

Double acting cylinders move more slowly but produce more force when __________.

Extending

50
New cards

As pump outlet pressure _______, pump’s internal leakage __________.

increases, increases

51
New cards

The two factors that determine the amount of internal leakage in a pump:

  • difference in pressure between inlet and outlet ports

  • amount of internal clearances within the pump


52
New cards

When a three-stage telescoping cylinder is operated, the greatest force is generated when…

The first stage is extended