Well Log Final

0.0(0)
Studied by 0 people
call kaiCall Kai
learnLearn
examPractice Test
spaced repetitionSpaced Repetition
heart puzzleMatch
flashcardsFlashcards
GameKnowt Play
Card Sorting

1/214

encourage image

There's no tags or description

Looks like no tags are added yet.

215 Terms

1
New cards



2
New cards

What is 'logging' in the petroleum industry?

The continuous measurement of a specific property of the formations crossed by a well, recorded against depth.

3
New cards

Which log type is normally displayed on a logarithmic scale

A) Gamma ray

B) Density

C) Resistivity

D) Caliper

C) Resistivity

  • Most other logs use linear scales.


4
New cards

What are the two main ways of acquiring well log data?

  1. Wireline logging

  2. LWD/MWD


5
New cards

What is one 'run' in wireline logging, and when is it usually made?

A single recording of a log

  • Runs are usually made at the end of each drilling phase, before casing is set (open-hole logs).


6
New cards

Give two advantages of LWD over wireline logging.

  1. It measures the formation before mud filtrate has invaded deeply

  2. It can log highly deviated or horizontal wells where wireline tools are hard or impossible to run


7
New cards

Give two disadvantages of LWD compared with wireline.

  1. It can be risky and expensive to run

  2. It often has a smaller range of tools available


8
New cards



9
New cards

What is TVDSS referenced to, and how is it obtained from TVD?

TVD Subsea

  • TVDSS = TVD minus the KB (kelly bushing) or RT (rotary table) elevation.


<p>TVD Subsea</p><ul><li><p>TVDSS = TVD minus the KB (kelly bushing) or RT (rotary table) elevation.</p></li></ul><p></p>
10
New cards

Why should well deviation surveys be checked before log analysis?

Inclination and azimuth are needed to plot the well path and compute TVDSS

  • Wells are sometimes loaded with wrong coordinates


11
New cards

Why is core analysis considered the most reliable source of formation properties?

Properties such as porosity, permeability and lithology are measured directly on rock samples in the lab rather than inferred from tool responses, and are thus more reliable.

12
New cards

Routine vs. special core analysis: which category includes relative permeability, wettability, capillary pressure, and the Archie Equation parameters m and n?

Special core analysis (SCAL)

  • Routine analysis covers porosity, horizontal permeability and fluid saturations


13
New cards

Are the following log tools considered passive or active?

  • Spontaneous Potential (SP)

  • Mud Log

  • Gamma Ray


Passive

  • All measure naturally occurring signals


14
New cards

Which logging tools are 'active', and what does that mean?

  • Density/PEF

  • Neutron

  • Sonic

  • Resistivity

  • NMR

They all send energy into the formation (gamma rays, neutrons, sound, current, magnetic fields) and measure the response

15
New cards

Match the units with the log:

Units:

  • μs/ft

  • API

  • g/cm3

  • mV

  • ohm-m

  • inches

  • b/e (barns/electron)

Log:

  • PEF

  • Resistivity

  • Gamma Ray

  • Sonic

  • Caliper

  • SP

  • Density


  • Sonic (μs/ft)

  • Gamma ray (API)

  • Density (g/cm3)

  • SP (mV)

  • Resistivity (ohm-m)

  • Caliper (inches)

  • PEF (barns/electron)


16
New cards

What is mudcake, and where does it form?

A layer of mud solids left on the borehole wall when mud filtrate enters the formation. It forms only opposite permeable beds.

17
New cards

What is the flushed zone (Rxo)?

The zone right next to the borehole where mud filtrate has replaced almost all of the movable formation fluid.

18
New cards

In porous formations, which fluid does a shallow-reading tool like the density tool mostly 'see'?

Mud filtrate in the invaded/flushed zone. As a result the density tool cannot easily tell oil from filtrate.

19
New cards

Why can gas still affect shallow porosity tools even after invasion?

Mud filtrate never fully displaces gas, so residual gas stays in the invaded zone and affects density and neutron readings.

20
New cards

What is the main advantage of the mud log?

It is the first log available, recorded while drilling, so it is especially valuable in exploration wells.

21
New cards

Name the five main components of a mud log.

(1) Mechanical properties (ROP, depth control), (2) cuttings sample descriptions, (3) gas analysis, (4) interpretations, (5) oil description.

22
New cards

What is ROP, and what two groups of parameters control it?

Rate of penetration. Formation parameters (lithology, porosity, pressure) and drilling parameters (weight on bit, rpm, bit type/age, drillstring configuration).

23
New cards

What is a 'drilling break'?

A sudden increase in ROP. It often means a softer, more porous lithology (e.g. a sand below a shale) or an overpressured zone.

24
New cards

How does mud weight relative to formation pressure affect ROP and gas readings?

Underbalanced (formation pressure greater than hydrostatic) drilling tends to raise ROP and gas readings. Overbalanced drilling suppresses both.

25
New cards

What is lag time in mud logging?

The time it takes cuttings and gas to travel from the bit up to the surface. Samples must be depth-corrected for it.

26
New cards

How can lag time be measured?

Pump a tracer down and time its round trip, then subtract the surface-to-bit time. Or time how long samples from a drilling break take to circulate up.

27
New cards

Name four tests used to detect hydrocarbon shows in cuttings.

Oil staining, hydrocarbon odour, oil fluorescence (%, intensity, colour), cut and cut fluorescence, cuttings gas analysis, and the acid test in carbonates.

28
New cards

Give three causes of poor cuttings samples.

Contamination (e.g. shale cavings), insufficient mud gel strength to lift the cuttings, lost circulation, and human error/carelessness.

29
New cards

Why are cuttings harder to depth-assign in soft sand/shale sequences?

Drilling is fast and the cuttings are small or disaggregated (often loose sand grains), so they are hard to classify and correlate with depth.

30
New cards

What does a second increase in fluorescence after a constant level suggest?

You may have passed from a gas zone into an oil zone. Fluorescence is highest in the main oil zone and lower in the gas zone.

31
New cards

What does a decrease in fluorescence indicate?

You have probably left the hydrocarbon zone.

32
New cards

What are C1 to C5 in mud gas chromatography?

C1 methane, C2 ethane, C3 propane, C4 butane, C5 pentane, reported in ppm.

33
New cards

Compared with background, what gas signature suggests a gas zone?

A dramatic increase in C1 and C2, dominated by methane.

34
New cards

Compared with background, what gas signature suggests an oil zone?

An increase in all components, with relatively more heavy compounds (C3+).

35
New cards

Seal rocks typically show what kind of gas composition?

High methane (C1), with some C2 and possibly C3.

36
New cards

What is the Pixler plot used for?

Plotting mud-gas hydrocarbon ratios (C1/C2, C1/C3, C1/C4, C1/C5) to classify a zone as productive gas, productive oil or nonproductive (Pixler, 1969).

37
New cards

On a Pixler plot, do low ratios indicate oil or gas?

Oil. Low C1/Cn ratios mean relatively more heavy components. Higher ratios plot in the gas field, and very high or very low ratios are nonproductive.

38
New cards

Does a large gas show on the mud log always mean a large quantity of producible gas?

No. A show is a deviation from background and does not necessarily mean a significant quantity of gas.

39
New cards

Midterm-style: very low GR, strong negative SP, DPHI 22%, NPHI 8%, mud gas C1 = 90%. What is the fluid?

Gas. The neutron-density separation (DPHI much greater than NPHI) is the gas crossover effect, and methane-dominated mud gas confirms it.

40
New cards

Midterm-style: Interval A has C1 = 90%. Interval B has C1 = 50% and C2-C5 = 50%, with NPHI close to DPHI. Which is oil?

Interval B. Wetter (heavier) gas and no neutron-density gas separation point to oil. Interval A is gas.

41
New cards

What does the caliper log measure, and in what units?

The diameter (size and shape) of the borehole, in inches.

42
New cards

What reference line is shown with the caliper curve?

Bit size. A caliper reading above bit size means hole enlargement. A reading below bit size means hole reduction.

43
New cards

What is an 'in-gauge' hole, and why does it matter?

A hole with the same diameter as the bit. It gives reliable log readings with few corrections.

44
New cards

What is a washout (caved hole)?

A section where the borehole diameter is much larger than bit size, caused by collapse, erosion by the mud, or the rotating pipe.

45
New cards

Why are washouts usually associated with shales?

Shales, especially shallow, unconsolidated, fractured or water-sensitive (swelling) ones, are mechanically weak and cave or slough easily.

46
New cards

Besides shale, which lithology commonly caves?

Coal and organic-rich shales, because they are fractured.

47
New cards

A smooth caliper reading slightly LESS than bit size usually indicates what?

Mudcake build-up, which means a permeable bed.

48
New cards

Why is mudcake a useful indicator of permeability?

Mudcake only forms where filtrate can enter the formation, i.e. permeable beds. Its vertical limits mark the limits of the potential reservoir.

49
New cards

A serrated caliper reading smaller than bit size suggests what?

Swelling clays (e.g. smectite) taking up water from the mud and squeezing into the hole, forming tight spots.

50
New cards

How is mudcake thickness estimated from the caliper?

Take the decrease in hole size (bit size minus caliper) and divide by two, because mudcake lines both sides of the hole.

51
New cards

Why might the density tool's caliper read a thinner mudcake than a microlog caliper?

The density pad is pushed against the wall harder and can cut a groove in the mudcake.

52
New cards

1- and 2-arm calipers vs. 3-arm calipers: which hole dimension does each tend to measure?

1- and 2-arm calipers tend to measure the maximum diameter of a non-round hole. 3-arm calipers measure closer to the minimum.

53
New cards

What is an X-Y caliper?

A 4-arm caliper that records two independent diameters at right angles. It gives the hole shape (e.g. oval breakouts) and better hole-volume estimates.

54
New cards

What are multifinger calipers used for?

Cased-hole inspection of casing or tubing wear, corrosion and scale, using about 12 to 80+ fingers.

55
New cards

Why should caliper logs always be checked with density and PEF logs?

Pad tools have a shallow depth of investigation, so washouts and rugosity badly degrade their readings.

56
New cards

What does the SP log measure, and in what units?

The natural potential difference (in mV) between an electrode in the borehole and a reference electrode at the surface.

57
New cards

What three conditions are needed to generate an SP response?

(1) A conductive fluid in the borehole, (2) a porous, permeable bed bounded by an impermeable one (shale), (3) a salinity contrast between mud filtrate and formation water.

58
New cards

Can the SP log be run in oil-based mud? Why?

No. Oil-based mud is non-conductive, so no current can flow.

59
New cards

What are the two electrochemical EMFs behind the SP?

Diffusion (liquid-junction) potential and shale (membrane) potential.

60
New cards

Which EMF is larger, and roughly what share of the SP does each contribute?

Shale (membrane) potential is about 83%. Diffusion (liquid-junction) potential is about 17%.

61
New cards

Explain diffusion potential.

Where saline formation water meets fresher mud filtrate in a permeable sand, Cl- ions (smaller, more mobile) diffuse faster than Na+. This leaves excess negative charge in the dilute solution, so the sand reads negative.

62
New cards

Explain shale (membrane) potential.

Negatively charged clay surfaces let Na+ through but hold back Cl-. Excess Na+ builds up on the dilute (borehole) side, giving a positive response opposite shales.

63
New cards

What is the shale baseline?

The fairly constant SP reading opposite thick shales. It is used as the zero reference, and deflections are measured from it.

64
New cards

When Rmf > Rw (fresh mud, salty formation water), which way does the SP deflect in a clean sand?

Negative (to the left of the shale baseline).

65
New cards

What happens to the SP when Rmf < Rw?

The deflection reverses (positive). When Rmf = Rw there is no deflection.

66
New cards

Does the SP measure absolute values?

No. It records relative changes. Changes occur at bed boundaries, and deflections are measured from the shale baseline.

67
New cards

What is the Static SP (SSP)?

The ideal maximum SP deflection in a thick, clean, permeable, water-bearing bed when no current flows. It is read from the thickest clean sand.

68
New cards

What is the SSP used for?

Estimating Rw (through the Rmf/Rw ratio) and acting as the clean end-point for SP-derived Vshale.

69
New cards

Give five reasons why the SP may not reach its full (static) deflection.

Thin beds, deep invasion, shale in the formation, hydrocarbons, and lithological complications (high-resistivity beds).

70
New cards

What is PSP?

Pseudo-static SP: the SP read in a shaly, water-bearing sand. It is smaller than the SSP because of shale content.

71
New cards

Is SP-derived Vshale more or less reliable than GR-derived Vshale?

Less reliable. It is more qualitative and usually overestimates Vshale. GR is preferred.

72
New cards

Name three main uses of the SP log.

Finding permeable beds and their boundaries, estimating Rw, estimating Vshale. Also facies/grain-size trends and correlation (used with care).

73
New cards

Can a permeable bed show no SP deflection?

Yes, rarely, when there is no salinity contrast between mud filtrate and formation water (Rmf = Rw).

74
New cards

Name two cases where the SP deflects even though the bed is not permeable.

Mineralization such as pyrite, and coals (which may show a large negative deflection or none).

75
New cards

In the carbon-storage SP exercise, what salinity cutoff defines a USDW aquifer?

10,000 ppm. Injection zones must have formation water saltier than this.

76
New cards

What does the natural gamma ray log measure, and in what units?

The natural radioactivity of the formation, in API units (typically 0-200 API).

77
New cards

Which three elements produce most natural gamma radiation in rocks?

Potassium (K-40), Uranium (U-238 series) and Thorium (Th-232 series).

78
New cards

Why are shales high on the gamma ray log?

Clays and associated minerals contain K and adsorb U and Th, so shales are more radioactive than clean sandstones and limestones.

79
New cards

What are the characteristic gamma energy peaks of K, U and Th?

K: 1.46 MeV (single energy). U: 1.76 MeV (Bi-214). Th: 2.62 MeV (Tl-208).

80
New cards

Is the GR tool passive or active?

Passive. It only records natural radiation.

81
New cards

What is the difference between a total (NGR) and a spectral (SGR) gamma ray tool?

NGR records total counts. SGR splits the spectrum into energy windows (5 windows) to give separate K (%), U (ppm) and Th (ppm) concentrations.

82
New cards

Which detectors are used for gamma ray logging?

Scintillation detectors (and historically Geiger-Müller tubes). They record counts per unit time.

83
New cards

What happens to gamma rays below about 0.5 MeV in the formation?

They are absorbed by photoelectric absorption.

84
New cards

What interaction dominates for medium-energy gamma rays (0.5-3 MeV)?

Compton scattering. The gamma ray loses energy step by step in collisions with electrons.

85
New cards

What happens to gamma rays above about 3 MeV?

Pair production: the photon is converted to an electron-positron pair near the nucleus. This is a minor effect.

86
New cards

Why does KCl mud affect GR and spectral GR logs?

It adds potassium radioactivity to the background, so total GR and K read too high. Because of the 5-window fit it also distorts U and Th (U can even read negative).

87
New cards

Why is KCl added to drilling mud?

To prevent clay swelling.

88
New cards

How does barite mud affect spectral GR?

Barite strongly absorbs low-energy gamma rays. This suppresses the U estimate and increases the Th and K estimates.

89
New cards

How does a larger borehole diameter affect GR counts?

It lowers counts, because more mud lies between the tool and the radioactive formation.

90
New cards

Name three borehole/operational factors that affect GR reliability.

Hole size and condition, mud type (KCl, barite, bentonite), logging speed, casing and cement.

91
New cards

Typical GR ranges: limestone, sandstone, shale?

Limestone about 5-10 API, sandstone about 10-30 API, shale about 80-140 API.

92
New cards

What GR response would a hot (organic-rich) shale give, and why?

Very high (more than 200 API). Organic matter concentrates uranium, so high GR reflects high TOC. Such shales are potential source rocks.

93
New cards

Can coals be confused with clean sands on GR? How do you tell them apart?

Yes, pure coals have low GR. Use the density log (coal has very low density) and the caliper (coal often caves).

94
New cards

What is the GR index (IGR)?

IGR = (GRlog - GRmin)/(GRmax - GRmin), where GRmin is the sand (clean) line and GRmax is the shale line.

95
New cards

Why is it wrong to assume Vshale = IGR in all rocks?

The IGR-Vshale relationship is often non-linear. Non-linear corrections (Larionov tertiary/older rocks, Clavier, Stieber) usually give lower Vshale, especially in young rocks.

96
New cards

Which gives lower Vshale for the same IGR, the linear or the Larionov tertiary equation?

Larionov tertiary (young rocks) gives the lowest. The older-rock equation is between it and linear.

97
New cards

Name two methods for picking GR sand and shale baselines.

The 'gut feel' method (drawn by eye) and the histogram method (statistical end-points from the formation's GR distribution).

98
New cards

What happens to Vshale if the shale line (GRmax) is set too high?

Vshale is underestimated, which overestimates net reservoir / gross pay.

99
New cards

Vclay vs. Vshale: are they the same?

No. Shale contains clay plus silt and other minerals, so Vclay < Vshale. Treating Vclay as Vshale underestimates shale.

100
New cards

What does a cylinder (blocky) GR shape usually indicate?

Uniform deposition, e.g. aeolian dunes, tidal sands, fluvial channels.