1/95
Comprehensive vocabulary flashcards covering Mechanics (91171), Waves (91170), and Electricity & Electromagnetism (91173) for NCEA Level 2 Physics exam revision.
Displacement
The change in position from the starting point to the finishing point, including direction; it is a vector quantity.
Distance vs. Displacement
Distance is the total path travelled (a scalar), whereas displacement is the straight-line change from start to finish with a specified direction (a vector).
Gradient of a Displacement–Time Graph
Represents velocity. A steeper gradient corresponds to a greater speed, while a negative gradient represents motion in the opposite direction.
Gradient of a Velocity–Time Graph
Represents acceleration. A positive gradient indicates positive acceleration, whereas a negative gradient indicates negative acceleration.
Area Under a Velocity–Time Graph
Represents displacement. Any area situated below the time axis is counted as negative displacement.
Constant-Acceleration Equations
The kinematic formulas for uniform acceleration: v=u+at, s=ut+21at2, v2=u2+2as, s=21(u+v)t, and a=ΔtΔv.
Acceleration Due to Gravity (g)
The downward acceleration of approximately 9.8ms−2 experienced by a freely falling object near the Earth's surface when air resistance is negligible.
Free Fall in a Vacuum
The condition where gravity gives all objects an equal acceleration g regardless of their mass, causing them to fall and accelerate at identical rates in the absence of air resistance.
Air Resistance (Drag)
An upward resistive force that opposes downward motion and increases with speed, thereby decreasing the resultant downward force and downward acceleration of a falling object.
Terminal Velocity
The constant speed reached by a falling object when the upward air resistance balances its downward weight, causing the resultant force and acceleration to equal zero.
Projectile Motion
Curved motion resulting from constant horizontal velocity (with zero horizontal force, ignoring drag) combined with changing vertical velocity caused by downward acceleration due to gravity.
Method for Analysing Projectile Motion
Analysing motion by treating horizontal and vertical components independently: horizontal acceleration is zero, vertical acceleration is downward g, and time is common to both.
Resultant Force
The single force that has the identical overall effect as all forces acting concurrently; calculated as the vector sum of all individual forces.
Newton's First Law
An object remains at rest or continues to move at a constant velocity unless acted upon by a non-zero resultant force.
Newton's Second Law
The resultant force acting on an object equals its mass multiplied by its acceleration (F=ma), with acceleration directed along the resultant force.
Newton's Third Law
When two objects interact, each exerts an equal-sized force in the opposite direction on the other, with the forces acting on separate objects.
Action–Reaction Forces
Paired interaction forces that cannot cancel each other out because each force acts on a different object rather than on the same object.
Resolving a Force
Splitting a single vector force into perpendicular horizontal and vertical components using trigonometry, allowing forces along each direction to be added independently.
Equilibrium
The state of an object where both the resultant force and resultant torque are zero, resulting in zero linear acceleration and zero angular acceleration.
Torque (Moment)
The turning effect of a force, calculated as the force multiplied by the perpendicular distance from the pivot: τ=Fd.
Hooke's Law
The principle stating that for a spring within its elastic limit, the restoring force is directly proportional to the extension: F=kx, where k is the spring constant.
Proportional Limit
The boundary beyond which extension is no longer directly proportional to the applied force and the spring may suffer permanent deformation.
Centripetal Acceleration
Acceleration directed towards the centre of a circular path that continuously changes the direction of velocity: ac=rv2.
Circular Motion at Constant Speed
Motion in which speed remains constant but acceleration exists because velocity is a vector whose direction is continuously changing.
Centripetal Force
The inward resultant force required for circular motion; it is provided by existing forces such as tension, friction, gravity, or normal reaction rather than being a separate force.
Centripetal Force–Speed Dependency
The relationship described by Fc=rmv2, showing that centripetal force depends on the square of speed and quadruples when speed doubles at constant radius.
Momentum
A vector quantity defined as mass multiplied by velocity (p=mv), pointing in the same direction as velocity.
Conservation of Momentum
The principle stating that within an isolated system having zero resultant external force, the total momentum before an interaction equals the total momentum after.
Impulse
The change in momentum, defined as Δp=FΔt for a constant resultant force, which is also equal to the area under a force–time graph.
Impact Force and Collision Time
The relationship showing that for an identical change in momentum, increasing contact time decreases the average force experienced, according to F=ΔtΔp.
Work and Power
Work is energy transferred by a force acting through a displacement along its direction (W=Fd); power is the rate of energy transfer (P=tW).
Energy Transformations in Free Fall
The conversion of gravitational potential energy into kinetic energy as an object descends, with total mechanical energy remaining conserved if resistive forces are negligible.
Wave Parameters (Amplitude, Wavelength, Frequency, Period)
Amplitude is maximum displacement; wavelength is distance between adjacent points in phase; frequency is cycles per second (Hz); period is time taken for one complete cycle.
Wave Equation
The formula v=fλ, stating that wave speed equals frequency multiplied by wavelength.
Frequency–Period Relationship
The inverse relation f=T1, where a higher frequency corresponds directly to a shorter wave period.
Wavelength Change with Increasing Frequency
Because wave speed remains constant within the same medium, an increase in frequency causes wavelength to decrease in accordance with v=fλ.
Wave Frequency Across Boundaries
The property that wave frequency remains unchanged when crossing media because it is determined by the source, whereas wave speed and wavelength may change.
Reflection at a Plane Boundary
The bouncing of a wave off a boundary such that the angle of incidence equals the angle of reflection, both measured from the normal.
Wave Pulse
A single travelling disturbance that transports energy through a medium without any overall transfer of matter.
Principle of Superposition
When two wave pulses overlap, the resultant displacement at any point is the algebraic sum of their individual displacements.
Constructive Interference
The superposition occurring when two waves meet in phase, causing their displacements to combine and produce a larger resultant amplitude.
Destructive Interference
The superposition occurring when two waves meet out of phase, causing their displacements to partially or entirely cancel out.
Diffraction
The spreading out of waves as they pass through a gap, which becomes greatest when the gap width is similar to the wavelength.
Slit Width Effect on Diffraction
When wavelength is unchanged, a narrower slit causes greater spreading of the wave, whereas a wider slit causes less spreading.
Wave Entering a Slower Medium
When a wave transitions into a medium where it travels slower, its frequency remains constant while its wavelength decreases according to v=fλ.
Mechanism of Refraction
The bending of a wavefront as it enters a new medium at an angle because one side of the wavefront changes speed before the other.
Refraction Towards the Normal
The change in wave direction towards the normal that occurs when a wave enters a medium where it travels more slowly, decreasing wavelength at constant frequency.
Refraction Away from the Normal
The change in wave direction away from the normal that occurs when a wave enters a medium where it travels faster, increasing wavelength at constant frequency.
Refractive Index (n)
A measure of how much light slows in a material: n=vc, where c is light speed in a vacuum and v is speed in the material.
Snell's Law
The mathematical relationship for refraction at a boundary: n1sin(θ1)=n2sin(θ2), where angles are measured relative to the normal.
Total Internal Reflection (TIR)
The complete reflection of light inside a higher-index medium when incident upon a lower-index boundary at an angle greater than the critical angle.
Conditions for Total Internal Reflection
Light must travel from a medium of higher refractive index towards one of lower refractive index, and the angle of incidence must exceed the critical angle.
Critical Angle (C)
The angle of incidence in a higher-index medium that produces an angle of refraction of 90∘ to the normal along the boundary.
Critical Angle Formula
For a material-to-air boundary, sin(C)=n1, demonstrating that a higher refractive index yields a smaller critical angle.
Converging (Convex) Lens Refraction
The bending of rays travelling parallel to the principal axis inwards towards the axis so that they converge at the focal point.
Principal Focus (Converging Lens)
The specific point where incident rays parallel to the principal axis converge and intersect after passing through the lens.
Image for Object Beyond 2F (Converging Lens)
Forms an image that is real, inverted, smaller than the object, and located between F and 2F on the opposite side of the lens.
Image for Object Between F and 2F (Converging Lens)
Forms an image that is real, inverted, larger than the object, and located beyond 2F on the opposite side of the lens.
Image for Object Inside F (Converging Lens)
Forms an image that is virtual, upright, enlarged, and situated on the same side of the lens as the object.
Magnification (m)
The ratio given by m=object heightimage height=object distanceimage distance.
Negative Magnification
Indicates that the formed image is inverted relative to the object, with the numerical magnitude specifying its relative size.
Thin Lens Equation
The relationship f1=do1+di1, where f is focal length, do is object distance, and di is image distance.
Concave Mirror Image Formation
The reflection of incident rays parallel to the principal axis so they converge at the focal point, forming images whose position and size vary with object distance.
Real vs. Virtual Image
A real image forms where light rays physically intersect and can be focused on a screen; a virtual image appears to come from a point where rays do not actually meet.
Electric Current (I)
The rate of flow of electric charge: I=tQ, measured in amperes (A).
Voltage (Potential Difference, V)
The energy transferred per unit charge between two points in a circuit: V=QE, measured in volts (V).
Electrical Resistance (R)
The opposition a component offers to the flow of current: R=IV, measured in ohms (Ω).
Ohm's Law
For a conductor at constant temperature, voltage is directly proportional to current: V=IR.
Resistance–Current Relationship at Constant Voltage
Current decreases as resistance increases according to I=RV, because constant voltage pushes fewer charges through a larger resistance.
Resistors in Series
A configuration where identical current passes through each resistor, total resistance is RT=R1+R2+…, and supply voltage is shared.
Resistors in Parallel
A circuit arrangement where each branch experiences the same voltage, total current splits between branches, and total resistance satisfies RT1=R11+R21+….
Adding a Parallel Branch
Provides an extra pathway for electric charge, raising total circuit current for the same supply voltage and thereby reducing the total equivalent resistance.
Voltage in a Parallel Circuit
The potential difference across every parallel branch is identical to the potential difference across the entire parallel network.
Current at a Junction
The total electric current entering a junction equals the total electric current leaving it, illustrating the conservation of electric charge.
Electrical Power (P)
The rate of electrical energy transfer, calculated as P=IV and measured in watts (W).
Electrical Energy Transfer (E)
The quantity of energy transferred by an electrical component over time: E=Pt=VIt.
Resistor Heating Mechanism
The increase in internal energy and temperature caused when charge carriers collide with lattice atoms in a resistor, transferring energy to the lattice.
Electric Field
A region of space where an electric charge experiences an electrostatic force.
Electric Field Direction
The direction of the electrostatic force exerted on a positive test charge: pointing away from positive charges and towards negative charges.
Uniform Electric Field
A field represented by straight, parallel, equally spaced field lines, indicating uniform field strength and constant direction.
Electric Field Strength (E)
The electrostatic force per unit positive charge: E=qF, which evaluates to E=dV in a uniform electric field.
Electrostatic Force on a Charge
The force given by F=qE, which acts along the field lines on a positive charge and in the opposite direction on a negative charge.
Electric Potential Energy Change (ΔEp)
The change in potential energy when a charge q moves through a potential difference V, having magnitude ΔEp=qV.
Work Done in an Electric Field
The work performed when moving a charge q through a potential difference V, calculated as W=qV.
The Motor Effect
The force experienced by a current-carrying conductor in an external magnetic field due to the interaction between the field of the conductor and the external field.
Force on a Straight Wire in a Magnetic Field
The force given by F=BIL when the wire is perpendicular to the magnetic field, where B is magnetic field strength, I is current, and L is wire length.
Factors Affecting Force on a Wire
Increasing magnetic field strength, current, or length of wire inside the field; the maximum force occurs when the wire is perpendicular to the field.
Hand Rule for Force Direction on a Wire
A three-finger or left-hand rule keeping current, magnetic field, and force mutually perpendicular to determine the direction of the magnetic force.
Magnetic Force on a Moving Charge
The deflecting force F=Bqv acting when a charge q moves at speed v perpendicular to magnetic field B, perpendicular to both velocity and field.
Circular Motion of a Charge in a Magnetic Field
Curved circular motion occurring because the magnetic force is perpetually perpendicular to velocity, changing the direction of motion without altering speed and functioning as a centripetal force.
Conditions for Zero Magnetic Force
Occurs when an electric charge is stationary or when it travels parallel or antiparallel to the magnetic field lines.
Induced Voltage in a Moving Conductor
The potential difference V=BvL created when a conductor moves across magnetic field lines, separating internal charges when mutually perpendicular.
Factors Increasing Induced Voltage
Increasing the magnetic field strength (B), conductor speed (v), or length of the conductor inside the field (L) according to V=BvL.
Conductor Motion Parallel to Magnetic Field
Produces zero induced voltage because the conductor does not cut across field lines, creating no charge-separating magnetic force along its length.
Kinetic Energy and Speed Relationship
Defined by Ek=21mv2, demonstrating that kinetic energy scales with speed squared and quadruples if particle speed doubles.
Charge vs. Current
Charge (Q) is the amount of electricity transferred measured in coulombs (C), whereas current (I) is the rate of flow of charge measured in coulombs per second or amperes (A).