1/28
Looks like no tags are added yet.
Tensile Strength of Steel (Strain-stress Curve)
PURPOSE: Determines what kind of steel you have with tensile strength
STEPS:
1. Measure center diameter of rod to nearest 0.001 in
2. Mark gage length
3. Grip outside of gage length with machine
4. Apply load at constant rate
5. Measure extensions at predetermined intervals
6. When increase in load stops, record it (yield point)
7. Determine yield strength using the offset
8. Plot stress-strain diagram
9. Calculate tensile strength
10. Calculate elongation over the gage length and percentage increase
Compressive Strength of Wood Parallel to the Grain
PURPOSE: To find the compressive strength of a given sample of wood
STEPS:
1. Make sure end of specimen is level
2. Position under crosshead of testing machine
3. Apply load at 0.024in/min
4. Measure change in length using compressometer
5. Continue loading past proportional limit
6. Read deformation to the 0.0001 in
Flexural Strength/ Modulus Rupture of Timber
PURPOSE: Measures tensile strength of wood sample
STEPS:
1. Measure cross section
2. Position on support with 18 in span length
3. Apply load at center of specimen at 0.1 in/min
4. Load until failure
5. Note max load and type of failure
Materials Finer than 0.075mm (No. 200) Sieve by Washing
PURPOSE: Done in order to determine the amount of fine material in a sample by the method of washing and passing through Sieve No. 200
STEPS:
1. Record dry mass of aggregate
2. Stack sieves with No. 200 on bottom
3. Place agg. in a bucket and cover with water, stir and agitate, empty water, repeat until water is clear
4. Pour agg. in a pan and dry in oven
5. Record dry mass
Specific Gravity and Absorption of Coarse Aggregates
PURPOSE: Determines the specific gravity and absorption of coarse aggregates
STEPS:
1. Make agg. SSD condition with towel
2. Weigh SSD aggregate
3. Place SSD aggregate in bucket underwater and attach to hook
4. Record under water mass
5. Empty into pan then oven dry overnight
6. Measure mass of agg sample and pan
7. Determine Bulk Specific Gravity with calculations
Percent Solids and Voids in Concrete Aggregates
PURPOSE: Used to find percent of voids or solids in aggregate
STEPS:
1. Calculate mass of empty bucket
2. Fill bucket 1/3 then tamp 25x
3. Fill bucket 2/3 then tamp 25x
4. Fill bucket 3/3 then tamp 25x
5. Level the bucket surface
6. Weigh bucket and find net weight of aggregate
Sieve Analysis of Fine Aggregates
PURPOSE: Determines gradation curve of the sample
STEPS:
1. Clean and stack sieves
2. Weigh dry aggregate
3. Pour aggregate into sieves
4. Place in shaker for 10 min
5. Remove stack and separate sieves and determine mass of sieve and aggregate
6. Clean and re-stack
Sand Equivalent
PURPOSE: Used for finding abundance of sand and clay in a sample of find material
STEPS:
1. Acquire sand and pour into cylinder using funnel
2. Stick metal tube into plastic cylinder and begin flow of Calcium Chloride then agitate by pushing tube to bottom and mixing
3. Add solution until 15 in mark
4. Let mixture stand 10 min
5. Put stopper on cylinder then invert several times
6. Place in mechanical shaker for 45 sec then rest 20 minutes
7. Record top level of dry clay
8. Place weighted foot assembly into the cylinder and read the top mark at the white circle. Subtract 10 in to determine height of sand
LA Abrasion Test
PURPOSE: Determines the hardness of aggregate
STEPS:
1. Weigh aggregate
2. Place in LA Machine with 11 - 1 lb steel balls
3. Close lid and rotate for 500 revolutions at 30 rpm
4. Remove aggregate with steel ball then remove steel balls
5. Sieve aggregate through #12 sieve and separate
6. Wash retained aggregate until water runs clear
7. Dry in oven overnight and record mass of retained aggregate
8. Subtract retained from total mass to determine what passed through the #12 sieve
9. Divide mass passed through by total mass to obtain LA abrasion number
Fine Aggregate Angularity
PURPOSE: Helps understand the void space between the variety of aggregate
STEPS:
1. Weigh out listed sizes of aggregates
2. Add first agg. to pan then add the second and record total mass
3. Mix with spoon until homogenous
4. Pour agg. into cone
5. Level cylinder with spatula then tap to settle
6. Pour agg. into 200mL flask and determine mass of both flask and mixture
7. Add distilled water to flask and rotate to remove air, allow to sit then rotate again
8. Adjust distilled water to calibrate volume mark and weigh with all contents
9. Calculate uncompacted void content
Specific Gravity and Absorption of Fine Aggregates
PURPOSE: Calculates both specific gravity and absorption of fine aggregates
STEPS:
1. Empty damp sand onto pan
2. Use hair dryer to obtain SSD
3. Place cone on tray with sand
4. Scoop sand until 1/3 filled and tamp 25x
5. Fill to 2/3 and tamp 25x
6. Fill to 3/3 and tamp 25x
7. Clear and sand around cone
8. Remove cone and observe slump of material to determine if at SSD
9. Distribute sand the continue drying with hair dryer
10. Fill pycnometer with water to calibration line and determine mass
11. Partially remove water and add 500g of aggregate
12. Rinse sides of flask to push aggregate to the bottom
13. Rotate to remove entrapped bubbles
14. Fill flask completely to the line and record mass
15. Empty all contents onto pan and rise to ensure you got all of it
16. Oven dry overnight then record mass
Normal Consistency of Hydraulic Cement
PURPOSE: Determines the water/cement ratio
STEPS:
1. Measure 650g cement, measure percentage of water, let sit for 30 sec, mix bowl at slow speed for 30 sec, scrape sides for 15 sec, mix at medium speed for 1 minute
2. Remove form and space into rough sphere, toss in air 6 times, press ball into conical ring, trim top with spatula, place mold on glass surface under plunger
3. Move bottom of plunger to right above cement surface, adjust indicator to read 0mm, release plunger and examine depth at 30 sec, if outside of 9mm-12mm throw away specimen
Time of Setting of Hydraulic Cement with the Vicat Apparatus
PURPOSE: Tests materials to determine normal or standard consistency
STEPS:
1. Make new cement mix, place sample mold under Vicat apparatus, replace plunger with needle end facing glass
2. Let test mold sit for 30 min, lower needle to the surface and adjust the indicator to 0 mm, drop needle and record after 30 sec, repeat every 15 min until 25 mm (initial set time), continue test until needle does not penetrate sample (final set time)
Blain Fineness Test
PURPOSE: Used to determine the fineness of the cement particles
STEPS:
1. Measure 3g of cement
2. Place filter paper on top of metal disk then place cement inside
3. Place another filter paper over the cement and compact sample
4. Put cap on the capture after applying a small amount of grease to ensure air tightness
5. Remove the air using the pump, when it touches the mark on the manometer, close the valve
6. Remove the cap, when the fluid cross the second mark on the tube start the timer until the lower meniscus reaches the third mark
Mix Design-Batching, Making, Curing Concrete Specimens
PURPOSE: To make a concrete sample for testing
STEPS:
1. Weight Materials
2. Add coarse agg, sand, then some of the water and begin mixing
3. Add cement and the rest of the water while mixing
4. Mix until uniform
Slump Test
PURPOSE: Measures the consistency of a concrete batch to see how easily the concrete will flow
STEPS:
1. Start test within 5 minutes of collecting a fresh concrete sample
2. Place wet mold on non-absorbent surface
3. Place feet firmly to prevent uplift, fill to 1/3 and tamp 25x
4. Fill to 2/3 and tamp 25x
5. Fill to 3/3 and tamp 25x
6. Scrape off excess concrete to level the surface
7. Step off mold maintaining downward pressure
8. Remove mold in non-twisting motion in 3-7 sec
9. Flip cone over and measure slump by placing rod on the cone then measure concrete surface to rod
Air Content by the Pressure Method
PURPOSE: Gets the air content of a sample of concrete using a pressure meter
STEPS:
1. Pour concrete into 3 layers and tamp each
2. Tap perimeter of the mold 15 times with mallet
3. Make surface level smooth using a flat bar
4. Clean lip of bowl
5. Secure lid with open petcocks
6. Squeeze water into one side with water dropper until all the air escapes
7. Bleed off air until it reads initial pressure
8. Close petcocks and press on lever to release air into bowl
9. Tap gauge to stabilize reading and record air content to nearest 0.1%
10. Open petcocks to release the pressure and clean apparatus
Measuring Temperature off Freshly Mixed Concrete
PURPOSE: To periodically measure the temperature in freshly prepared concrete mix
STEPS:
1. Sample the concrete
2. Place thermometer in concrete
3. Press concrete toward thermometer
4. Leave for 2 minutes or until temp stabilization and record
5. Must be completed within 5 minutes after obtaining sample
7-Day Flexural Strength by Simple Beam 3rd Point Loading
PURPOSE: Measures 7-Day flexural test by 3rd point loading and allows us to record tensile strength when it fails
STEPS:
1. Measure length, width, and height of beam
2. Put beam into compressive strength device
3. Ensure third point loading on beam
4. Input diameter of beam in computer
5. Compress beam until failure
6. Record tensile strength of beam at failure
Mixing of Hydraulic Cement Mortars
PURPOSE: Material used to characterize cement in tests
STEPS:
1. Place water and cement in bowl and mix slowly for 30 sec
2. add sand over 30 sec period while mixing
3. Change mixer to medium speed for 30 sec
4. Stop mixer and let stand 1.5 min, scrape sides within 15 sec then cover with lid
5. Finish mixing for 1 min at med speed
6. Place 1 in of mixture into mold then tamp 20x
7. Top off mold and tamp 20x and even out
8. Drop 1/2 in 25x in 15 sec
9. Use calipers to determine flow
10. After flow test, return mortar to bowl and mix for 15 sec at med speed
Compressive Strength of Hydraulic Cement Mortars
PURPOSE: Determines the compressive strength of mortar cubes of different cement types/ages
STEPS:
1. Remove cement from molds and choose the best 3
2. Put one into the machine and load until failure
3. Record failure and divide by 4 square inches to determine compressive strength
Viscosity of Binders with the Rotational Viscometer
PURPOSE: Provides important results by determining the viscosity of bitumen and various temperatures set by the user
STEPS:
1. Set temperature on thermosel
2. Pour 8-10 mL of bitumen into holder
3. Stir bitumen and pour in 8-10mL
4. Place holder in the thermosel container
5. Align container so it's centered above the spindle hook
6. Attach spindle to hook and lower it into the container
7. Wait for temp of bitumen to stabilize
8. Start spindle rotation at 20 rpm
9. Record 3 readings at temps 60 sec apart
Shear Modulus and Phase Angle of Binders (DSR)
PURPOSE: Finds the stress used in determining the viscoelastic behaviors of binder at moderate to high temps
STEPS:
1. Put specimen in DSR
2. Squeeze asphalt between plates making sure the gap is 0.05mm, trim the specimen
3. Decrease the bap by 0.05 mm after trimming so the sample is the desired thickness
4. Bring specimen to test temp and begin test once temp is maintained for 10 min
5. Apply shear strain for 10 cycles at 10 rad/s
6. Data acquisition system will calculate the complex shear modulus and the phase angle
Low-temperature Stiffness with the Bending Beam Rheometer (BBR)
PURPOSE: Determines lower grade of bitumen
STEPS:
1. Turn on cooling unit and calibrate machine
2. Make the beam mold 6.25mmx12.5mmx127mm
3. Pour asphalt into mold and cool for 45 minutes
4. Trim and remove mold then place in cold bath for 60 +- 5 min
5. Place newly made beam on supports in BBR
6. Run automatic testing system, remove test load, and end test
7. Print results
28-Day Compressive Strength of Concrete + ANOVA analysis
PURPOSE: Tests the compressive strength of 28-Day material
STEPS:
1. Take the Sample out of the mold
2. Put caps on the ends
3. Put diameter into computer
4. Put cylinder on the compressive strength machine
5. Apply load in compression
6. Record peak load and calculate compressive strength
28-Day Splitting Tensile Strength
PURPOSE: Measures the compressive strength along its long axis
STEPS:
1. Place cylinder along its length on center of loading platform
2. Place strip across cross-section so that tension is along its diameter
3. Start loading the cylinder
4. Record maximum force at failure
Superpave Gyratory Compaction
PURPOSE: Allows us to compact the sample to a specific height or fixed number of gyrations
STEPS:
1. Heat mix and mold to specific temp needed for bitumen
2. Puyt filter paper at the bottom of heated mold
3. Place mix in funnel while it's still hot
4. Put another piece of filter paper on top
5. Place mold into compactor and start machine
6. Set compaction to 115 gyrations
7. After machine stops, take out mold using extractor
8. Let cool before handling
Theoretical Maximum Specific Gravity or Density of HMA
PURPOSE: Determines specific gravity of already mixed asphalt at room temp
STEPS:
1. Break pre-prepared sample into chunks and place into bowl then measure
2. Weigh hma + metal bowl
3. Cover all mix with water and put lid on then clamp shut
4. Start vacuum pump and shaker table for about 15 min
5. Stop pump and slowly release pressure from valve
6. Measure total weight of bowl + hma under water
7. Remove all mix from bowl and measure weight of empty bowl under water
Bulk Specific Gravity of Compacted HMA
PURPOSE: To calculate the Specific Gravity of an asphalt sample
STEPS:
1. Measure dry mass of sample
2. Tare the scale with the bucket
3. Put sample in the water for 10 min
4. Measure weight of sample inside water
5. Wipe surface with towel and measure SSD weight