1/213
Looks like no tags are added yet.
Surface Water Treatment plant order
Surface water supply (stream, river, or lake), Screen, Rapid mix, Flocculation basin, Sedimentation basin, Sludge leaves, Rapid sand filter, Disinfection, Storage, Pump, Distribution system
Water Softening Plant for Groundwater Treatment
Groundwater from wells, Rapid mixing, Reaction basin, Settling tank, Recarbonation, Rapid Sand filter, Disinfection, Pump, Storage, Distribution system
Where does water softening occur in groundwater treatment
reaction basin
grit chamber
removes sand size particles
primary settling tank
suspended solids removal
secondary settling tank
separation of biomass after biological treatment
four types of settling
class-1, class-2, zone settling, compression zone
y axis for settling
percent solids
x axis for settling
particles from discrete (individual) to flocculent (clumps)
Type 1, or class-1 settling
particles settle as separated units (no flocculation or interaction between particles)
Example of Type I settling
Wastewater treatment: settling of sand particles in grit chamber
Example of Type II settling
Wastewater treatment: Primary settling tank
Drinking water treatment: Settling of solids in water after coagulation/flocculation
Type II, or class-2 settling
settling of flocculant particles in a dilute solution (as flocs grow, the flocs settle faster)
Type III settling, or zone settling
particles are so close together that interparticle forces hinder the settling of neighboring particles, the particles remain in a fixed position relative to each other and all settle out at a constant velocity
Example of Type III settling
Wastewater treatment: intermediate depths of secondary settling tank
Type IV Settling, or compression settling
particles are at such a high concentration that the particles touch each other and settling can only occur by the compression of the compacting mass
Example of Type IV settling
wastewater treatment: lower depths of secondary settling tank
particle concentrations for type I and type II settling
0-200 mg/L
particle concentrations for type III settling
200 mg/L-3000 mg/L
Discrete particle settling is Type
I
particle behavior for type I settling
discrete particle settling
flocculant settling is type
II
particle behavior for type II settling
differential flow paths and flocculant particles
hindered or zone settling is type
III
particle behavior for type III settling
large number of particles from blanket that overtakes other particles
compression settling is type
IV
particle behavior for type IV
water displaced from pores as particles settle and compress, particles compact as settling proceeds
types of particles for discrete settling
low solids concentration and non-flocculant particles
three forces acting on a particle during settling
Fw weight of the particle, Fb buoyancy force, Fd drag force
Nre decribes
whether the flow is slow and orderly or very fast with a lot of turblence and eddies
region I
laminar flow
region II
transitional flow
region III
turbulent flow
in region I viscous forces are _____ intertia forces
more important than
in region II viscous forces are ____ intertia forces
equally as important as
in region III viscous forces are ___ inertia forces
less important than
Stoke’s law predicts
the settling velocity of a discrete but is only valid during laminar flow conditions
in type I settling region I the Nre is
less than one
in region III the Nre is
greater than 10^4
in region II Nre is
between 1 and 10^4
calculation method for type one settling particles in the laminar flow region
stokes law
calculation method for type one settling particles in the transitional flow region
trial and error
calculation method for type one settling particles in the turbulent flow region
vs=SQRT of 3.3*(ss-1)d
example of primary settling tank
valley forge wastewater treatment plant
Assumptions of Ideal Basin theory for rectangular tank
settling is type I, basin has four distinct zones, flow entering and leaving settling basin is evenly distributed, particles are uniformly distributed through the basin depth at the inlet end of the settling zone, there is uniform horizontal flow of water in settling zone, particles entering the sludge zone stay there, particles entering the outlet zone do not settle out
four distinct settling zones in rectangular basin
entrance zone, outlet zone, sludge zone, settling zone
column test for type I settling
use a 1 liter capacity graduated cylinder with a sampling port, fill graduated cylinder with sample and mix thoroughly, allow settling and take periodic samples for total suspended solids analysis, calculate and tabulate fraction remaining versus settling velocity
“ideal basin” theory allows us to
derive an equation correlating the critical settling velocity to size of the tank
typical drinking water treatment process sequence
flocculation/coagulation, settling tank, filtration (sand filter)
design considerations for rectangular tanks
requires less land area for multiple tanks (therefore typically used for large flows), can be stacked when space is very limited
design considerations for circular tanks
simpler sludge removal mechanisms, requires less maintenance, horizontal water velocity continuously decreases as water comes in from center and moves out toward the edge
batch settling test for type I settling
use a 2 liter capacity graduated cylinger, fill graduated cylinder with simulated creek sample and mix throroughly, allow settling and take periodic samples from a distance H below surface and analyze for total suspended solids analysis, calculate and tabulate fraction remaining versus settling velocity, determin the required surface overflow rate for 85% removal
does iron 3+ contribute to hardness
yes because it is a cation and the valence is larger than one
does sodium contribute to hardness
no because although sodium is a cation its valence is equal to one
what is hardness caused by
the presence of polyvalent cations, particulary calcium (Ca2+) and magnesium (Mg 2+)
what does water hardness cause
excessive use of soap and scaling on bathroom fixtures and heating elements of water heaters
calcium can be removed by
precipitating it as CaCO3
Magnesium can be removed by
precipitating it as Mg(OH)2
what happens when carbon dioxide is bubbled into water
it lower pH
rain has a small percentage of
carbon dioxide
neutralization of carbon dioxide precipitates in
limestone
easiest hardness to remove
carbonate
how is carbonate hardness removed
can be removed by just heating the water
carbonate is a function of
alkalinity (buffering capacity showing how it changes or stabilizes pH)
why is non carbonate hardness called permanent
because it cannot be removed by heating the water
non carbonate hardness is defined as
the total hardness in excess of the total alkalinity
non carbonate hardness accounts for
the portion of Ca2+ and Mg2+ (and other multivalent cation) associated with ions other than HCO3- and CO3-2
the more Ca2+ and Mg2+ that dissolve in your water, the
harder the water is
what ions contribute to hardness
cations with valence greater than one
small scale hardness removal
ion exchanges for Ca2+ and Mg 2+ removal
large scale hardness removal
single-stage lime process, excess lime process, single stage lime-soda process, and excess lime-soda process
single stage lime process
for removal of high calcium carbonate and low magnesium carbonate hardess, just lime because there is enough bicarbonate and carbonate
excess lime process
for removal of high calcium and magnesium carbonate hardness (non-carbonate hardness is not removed)
single stage lime soda process
adding lime and soda ash, for removal of high calcium carbonate and low magnesium carbonate hardness (some calcium non carbonate hardness is removed), there is not enough bicarbonate or carbonate
excess lime soda process
for removal of high calcium and magnesium carbonate hardness and some non-carbonate hardness
true or false: you always need to add excess lime beyond stichometry amount
true
to achieve reasonable removal of hardness in a practical time period, an excess of lime ____ the stoichiometric amount is usually provided
greater than
carbonate hardness means
enough alkalinity, more bicarbonate compared to calcium, all carbonate hardness
noncarbonate hardness means
still cations (Mg2+, Ca2+) but not any more alkalinity
is it possible to remove all of the hardness from water
no because of the slight solubility of CaCo3 and Mg(OH2) and because some of the precipitate is present as a nonsettling floc
what does the lime soda process soften water to
between 30-80 mg/L (as CaCO3) residual hardness
what is hard water
water that contains excess Ca2+ and Mg2+ (as well as any other multi-valent cations)
hard water causes
pipes and water heaters to foul
why is lime added to hard water
to both raise the pH and to remove any carbonate hardness ((Mg(HCO3)2) or (Ca(HCO3)2)) present
why are soda ash and lime added together to hard water
to remove any non-carbonate hardness present
examples of non-carbonate
(CaCl2, Ca(SO4), Ca(SiO3), MgCl2, Mg(SO4), Mg(SiO3))
3a and 3b are always
equal
filtration
passing water through a porous media for seperation of solids (usually very fine solids that cannot be removed by coagulation/flocculation or settling)
According to Surface Water Treatment Rule (SWTR) under the Safe Drinking Water Act (SDWA) all surface waters must
be treated using filtration
depth filtration
process by which water flows slowly through a bed of granular media, usually sand, anthracite coal, or garnet, particles in the water become trapped in the granular media as the water passes through the filter bed
surface filtration
suspened solids are removed from liquid by sieving through a straining surface (filter material), pore openings generally range from 5 micrometers to 30 micrometers
membrane filtration
similar to surface filtration but able to remove dissolved constituents as well
membrane filtration includes
microfiltration and ultrafiltration
what does microfiltration include
0.1 micrometer pores, particles, sediment, algae, protozoa, bacteria
what does ultrafiltration include
0.01 micrometer pores, small colloids, and viruses
reverse osmosis includes
nanofiltration and reverse osmosis
what does reverse osmosis include
nonporus, it can remove dissolved solids, monovalent species (Na+, Cl-)
what does nanofiltration include
0.001 micrometer pores, dissolved organic matter, divalent ions (Ca2+, Mg2+)
media types of depth filters
single media, dual media, multiple media
flow types of depth filters
gravity and pressure filters